• 설비공학논문집
• /
• 제18권2호
• /
• pp.151-157
• /
• 2006

The present paper reports the method for evaluation of heat-transfer performance of finned tube heat exchangers in a low Reynolds number regime (Re = $160\~800$) and also reports the data of heat transfer and pressure loss taken from a finned tube heat exchanger with/without vortex generators (VGs) installed as a heat-transfer enhancement device. The evaluation is based on the modified single blow method conducted in a specially designed low Reynolds number duct. Three different test core geometries, i.e., fin only, fin-tube without VGs and that with VGs, are studied here. The data of heat transfer and pressure loss taken from the fin only geometry agree well with the empirical correlations, thus validating the present method as used for low Reynolds number regime. The data taken from the finned tube geometries with and without VGs are presented and compared to examine the effect of VGs in the low Reynolds number regime.

• International Journal of Fluid Machinery and Systems
• /
• 제10권3호
• /
• pp.197-208
• /
• 2017

When Francis turbines operate at partial load, residual swirl in the draft tube causes low-frequency pulsation of pressure and power output. Scale effects and system response may bias the prediction of prototype behavior based on laboratory tests, but could be overcome by means of a 1D analytical model. This paper deals with the two most important features of such a model, the compliance and the source of excitation. In a distributed-parameter version, compliance should be represented as an exponential function of local pressure. Lack of similarity due to different Froude number can thus be compensated. The normally unknown gas content in the vortex cavity has significant influence on the pulsation, and should therefore be measured and considered as a test parameter.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제23회 추계학술대회 논문집
• /
• pp.27-35
• /
• 2004

본 논문에서는 로켓 엔진의 고주파 연소불안정 현상이 연소현상과 맞물린 음향학적 현상이라는 점과 일반적으로 로켓엔진의 연소실 및 배기노즐이 원통형이라는 점을 고려하여 단면적이 변하는 원통형 관에서 음향, 엔트로피 및 와류 파동방정식의 해를 구하는 방법을 제시하였고 이를 통하여 엔트로피 및 와류파동이 음향파동에 미치는 영향을 정량적으로 해석 및 계산 할 수 있는 방법을 제시하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 추계학술대회 논문집
• /
• pp.101-106
• /
• 2011

In the present paper, the phenomena of abnormal noise and vibration due to acoustic resonance of CFBC(Circulating Fluidized Bed Combustion) boiler was presented. The acoustic resonance which occurred in the gas path of CFBC boiler system was caused by coincidence of vortex shedding frequency of tube bank and acoustic natural frequency of duct and hopper. And, the phenomena of beating arose from the interference of two closed resonant waves at 66.4Hz and 70.8Hz. There are two control methods for acoustic resonance in this system. The first method is to change the vortex shedding frequency from the structural alterations on the tube bank. And the second method is to change the acoustic natural frequency of the gas path with the installation of anti-noise baffles. The second one which is relatively easy to apply, was adapted in this study. As a result, the noise and vibration level have been decreased by 41dB and 94% at 66.4Hz, respectively. And the improvement of noise and vibration at 70.8Hz was identified by sensory evaluation.

• 한국산학기술학회논문지
• /
• 제16권5호
• /
• pp.2985-2992
• /
• 2015

본 연구에서는 엇갈린형 관군에 대해 ANSYS FLUENT v.14의 SST 난류모델을 적용하여 가로피치, 튜브표면, 와류발생기위치 등의 변화에 따른 열전달 및 압력강하 특성을 이론적으로 해석하였다. CFD 해석시 튜브표면의 온도는 363 K, 입구측 공기온도는 313 K이고 입구측 속도는 5 m/s에서 10 m/s까지 가정하였다. 그 해석결과로서 열전달계수는 가로피치에 대한 영향은 큰 차이가 없었고, 튜브표면의 돌기형상은 열전달 및 압력강하 특성에서 원형이 톱니형보다 적절하게 나타내었으며, 와류발생기의 설치 경우에는 열전달특성이 튜브의 전방부 위치가 후방부 위치보다 약 4.6% 정도로 우수함을 보였다.

• 한국산학기술학회논문지
• /
• 제21권4호
• /
• pp.446-451
• /
• 2020

전열관군으로 이루어진 열교환기에서 유동에 따른 진동은 전열 관군 배관의 파손을 유발할 수 있어서 열교환기에서 유동 유발 진동 특성을 규명할 필요가 있다. 본 연구는 전열 관군의 원관에서 입구의 유속이 일정한 경우와 주기적인 변동이 있는 경우에 대하여 시간에 따라 전열 관군 원관 1, 10 그리고 마지막 19번 원관에서 와류의 시간 변동 특성을 살펴보고 양력의 시간 변화 특성과 PSD 특성을 분석하여 전열 관군 원관에서 전방류의 주기적인 속도 변동에 따른 유동 특성을 규명하였다. 일정 입구 유속의 경우는 칼만 와류가 후류에 있는 원관의 유동에 영향을 미치고 있고 후류의 전열관군과 전방의 전열관군에서의 와류는 다소 시간적인 차이를 보여주지만 같은 주기의 칼만 와류를 발생하고 있음을 관찰할 수 있었다. 주기적인 입구 유속의 경우는 전열 관군에서 와류가 강한 유동이 흐르다가 유속이 줄어들 때는 와류가 약한 유동이 흐르는 것이 반복됨을 알 수 있다. 일정 입구 유속의 경우는 양력의 PSD로 살펴본 결과 주파수는 37.25Hz이며 19번 원관의 경우는 18.63Hz와 50Hz 근방에서 주파수가 관찰 되었다. 주기적인 입구 유속의 경우는 37.25Hz와 속도 주기인 18.63Hz에서 주된 주파수 특성을 보여주었다. 마지막 원관인 19번 원관은 20Hz에서 50Hz 사이에서 많은 피크 주파수를 관찰할 수 있었다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.1-4
• /
• 2014

The present work focuses on the analysis of the pulverized coal combustion aerodynamics of the dual swirl burner by the control of the swirl-modes such as the outer swirl intensity (OSI). The detailed structure of pulverized coal swirling flames with swirl-mode was studied experimentally by particle image velocimetry and local flame colors based on $OH^*$, $CH^*$, and ${C_2}^*$ radicals. For all co-swirling conditions, the internal recirculation zone (IRZ) was observed near the inner shear layer with respect to the processing vortex core structure. Furthermore, a co-rotating vortex in the outer shear layer and the exhaust tube vortex (ETV) along the central axis were observed. The intensity of $CH^*$ signal was higher with small coal particle size, conversely, the size of the distribution of the $CH^*$ signal becomes larger. Therefore, the control of the aerodynamics with changing swirl intensities may play an important role in improving both environmental and combustion performances.

• 한국전산유체공학회지
• /
• 제9권2호
• /
• pp.11-17
• /
• 2004

CFD analysis was performed to figure out flow behavior in the inlet plenum of new research reactor where coolant is injected to the flow tubes with the fuel assembly. The computation results showed that large-scale vortices are generated in the inlet plenum by flow stream injected from inlet pipe. These vortices are divided into small vortices and reversed their revolution. They may lead to flow-induced vibration of fuel assembly, moreover, which has been regarded as a cause of fretting wear of fuel assembly. Also there is an another important thing that average velocity of each flow-tube is uneven showing difference in maximum 18%. So it has been suggested that perforated baffle will be installed to prevent the formation of vortex in the inlet plenum. Two perforated baffles, one is flow skirt and the other is muffler type flow straightener, were proposed and their effect was evaluated using commercial CFD code, Fluent. According to CFD analysis for two perforated baffles, it was confirmed that both of them can prevent or reduce vortex formation in the inlet plenum and make average velocity of each flow tube more even.

• Nuclear Engineering and Technology
• /
• 제38권1호
• /
• pp.69-80
• /
• 2006

Fluid-elastic instability in an air-water two-phase cross-flow has been experimentally investigated using two different arrays of straight tube bundles: normal square (NS) array and rotated square (RS) array tube bundles with the same pitch-to-diameter ratio of 1.633. Experiments have been performed over wide ranges of mass flux and void fraction. The quantitative tube vibration displacement was measured using a pair of strain gages and the detailed orbit of the tube motion was analyzed from high-speed video recordings. The present study provides the flow pattern, detailed tube vibration response, damping ratio, hydrodynamic mass, and the fluid-elastic instability for each tube bundle. Tube vibration characteristics of the RS array tube bundle in the two-phase flow condition were quite different from those of the NS array tube bundle with respect to the vortex shedding induced vibration and the shape of the oval orbit of the tube motion at the fluid-elastic instability as well as the fluid-elastic instability constant.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.150-154
• /
• 2012

A flow induced mechanical vibration and acoustic resonance should be considered at design stage because they are mainly occurred in the tube bank of boiler. Acoustic resonance is occurred when the vortex shedding frequency of tube bank coincides with the acoustic natural frequency of the cavity. Effective solution to avoid acoustic resonance is installing acoustic baffles in the tube banks parallelly inside of the flow cavity. Thus, location and number of acoustic baffles should be exactly calculated to eliminate the acoustic resonance. This paper presents case study of acoustic resonance due to inappropriate number and location of acoustic baffles. Measured frequency and mode in the study is verified by FEM acoustic modal analysis. The number and location of acoustic baffles to avoid acoustic resonance are calculated by using FEM acoustic modal analysis.