• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.8
• /
• pp.667-673
• /
• 2001

As an alternative cooling method to reduce environmental hazard, vortex tubes have been studied for energy separation into cold and hot streams. Hence, the experiments were carried out systematically to find the best ratio of vortex chamber diameter to tube diameter. Also, the work was don to investigate how inlet pressure and geometric ratios of vortex tube affected temperature differences at tow needs as ell as cooling capacity and cooling efficiency. The result showed that the maximum temperature differences at the both ends and the maximum cooling efficiency were obtained when the ratio of vortex chamber diameter was about 1.45, while the inlet pressure ws not higher than 0.7 MPa.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.3
• /
• pp.338-345
• /
• 2000

A model testing has been performed to investigate the flow characteristics of a vortex chamber, which plays a role of a flow switch and passively controls the discharge flow rate. This method of passive flow control is a matter of concern in the design of advanced nuclear reactor systems as an alternative to the active flow control to provide emergency water to the reactor core in case of postulated accidents like LOCA (Loss-Of-Coolant Accident). By changing the inflow direction in the vortex chamber and varying the flow resistance inside the chamber, the vortex chamber can control passively the injection flowrate. Fundamental characteristics such as discharge flow rate and pressure drop of the vortex chamber are measured, and its parametric effects on the performance of the vortex chamber are also systematically investigated.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.17-22
• /
• 1996

차세대원자로의 안전계통 성능향상을 위하여 축압기 설계에서 채택하고 있는 피등적 유량조절 장치인 vortex 밸브의 특성을 분석하였다. 단순화된 해석모델을 이용하여 vortex chamber의 유동 pattern을 분석하였으며 vortex 밸브의 성능에 중요한 영향을 미치는 기하학적 인자들의 영향 유동모드 전환시 주유량이 공급되는 수관의 수위거동 특성을 분석하였다. 또한 3차원 모의가 가능한 FLUENT 코드를 사용하여 vortex chamber의 유동장을 해석하여 vortex 밸브의 유동특성을 분석하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.9
• /
• pp.731-737
• /
• 2014

A vortex chamber is a simple device that separates compressed gas into a high-temperature stream and a low-temperature stream. It is increasing in popularity as a next-generation heat exchanger, but the flow physics associated with it is not yet well understood. In the present study, both experimental and numerical analyses were performed to investigate the temperature separation phenomenon inside the vortex chamber. Static pressures and temperatures were measured using high-sensitivity pressure transducers and thermocouples, respectively. Computational fluid dynamics was applied to simulate 3D unsteady compressible flows. The simulation results showed that the temperature separation is strongly dependent on the diameter of the vortex chamber and the supply pressure at the inlet ports, where the latter is closely related to the viscous work. The previous concept of a pressure gradient wave may not be a reasoning for temperature separation phenomenon inside the vortex chamber.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.10a
• /
• pp.487-494
• /
• 1995

원자력발전소의 안전성 향상을 목적으로 신형원자로 안전주입계통의 축압기 설계에 적용이 고려되고 있는 피동적 유량조절 장치인 vortex 밸브의 유동장을 해석하여 밸브의 특성에 영향을 미치는 주요 인자들을 도출하고 이 인자들의 영향을 분석하였다. 분석 결과 Vortex 밸브의 성능 특성은 수송유량, 제어유량, chamber의 반경, 입구면적, 마찰계수 등의 영향을 받는 것으로 나타났으며 이들 인자 중 chamber의 반경의 영향이 가장 크고 Reynolds수의 영향은 비교적 작은 것으로 파악되었다. 또한 주어진 유동조건에서 제어유량이 작은 경우 점성손실이 vortex 밸브의 유동특성에 미치는 영향이 증대되는 경향을 보였으며 유량이 증가할수록 Reynolds수의 영향은 감소하는 것으로 나타났다.

• Journal of Wetlands Research
• /
• v.25 no.3
• /
• pp.176-183
• /
• 2023

The aim of this paper is to understand the blade number effect on vortex turbine performance in the cylindrical vortex chamber below the free water surface. Using the same blade profile, the performance of gravitational vortex turbine is tested each with 2, 3, 4, 5 and 6 blades installed at the relative vortex height (y/h_v) ranging from 0.065 to 0.417. The obtained results indicate that the rotation, voltage, current and power increase in the relative vortex height of 0.065 and 0.111 when increasing the number of blades at flow velocity of less than 0.7 m/s. The average power of the 5-blade turbine is more than others. The performance of the 4-blade turbine with a 130 mm diameter installed near the orifice is higher than that of the same number of blades with a 220 mm diameter in the vortex chamber.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.10-17
• /
• 2000

This work presents an investigation of aerodynamic characteristics of fuel spray injected from a high pressure hollow cone swirl injector into a constant volume chamber. Laser tomography visualization was used to interrogate the fuel and air mixing characteristics and the effect of chamber pressure and temperature increase was analyzed, Preliminary results on spray development showed that mixing effect tends to increase with the increase of injection pressure and chamber gas pressure yielding a decrease of spray penetration and an attenuation of well-defined vortex structure. Topological analysis of the spray structure has been performed to initiate the understanding of mixing and vaporization process. For the present experimental conditions fuel injection pressure and chamber gas pressure appear as the dominant factors which govern the transient mixing characteristics. Moreover spray atmixation characteristics are improved by increasing chamber gas temperature.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.244-248
• /
• 2012

A series of hybrid rocket combustion experiments were carried out with PMMA/GOx changing diameter and length of the disk installed at pre-chamber. The disk can generate vortex shedding flow and change flow conditions prior to entering the fuel grain which could also alter the combustion characteristics and pressure oscillations. The interaction of vortex shedding in the pre-chamber and small-scale vortices adjacent to burning surfaces by using combustion test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.7
• /
• pp.2945-2950
• /
• 2011

As the step to improve fuel efficiency, there is the system to build up the eddy of combustion chamber at the suction line in order to increase the combustion efficiency. The models installed with no vortex generation system or with various shapes of the system are examined by fluid analysis. Vortex generation system is installed prior to the suction of combustion chamber. The wing of this system winds itself around the suction air and generates the vortex. This study investigates the flow of suction air and the pressure distribution of suction stroke by using the eddy generation system.

• Nuclear Engineering and Technology
• /
• v.51 no.5
• /
• pp.1279-1288
• /
• 2019

The vortex-type fluidic diode (FD) is a key safety component for inherent safety in various advanced reactors such as the sodium fast reactor (SFR) and the molten salt reactor (MSR). In this study, topology optimization is conducted to optimize the design of the vortex-type fluidic diode. The optimization domain is simplified to 2-dimensional geometry for a tangential port and chamber. As a result, a design with a circular chamber and a restrictor at the tangential port is obtained. To verify the new design, experimental study and computational fluid dynamics (CFD) analysis were conducted for inlet Reynolds numbers between 2000 and 6000. However, the results show that the performance of the new design is no better than the original reference design. To analyze the cause of this result, detailed analysis is performed on the velocity and pressure field using flow visualization experiments and 3-D CFD analysis. The results show that the discrepancy between the optimization results in 2-D and the experimental results in 3-D originated from exclusion of an important pressure loss contributor in the optimization process. This study also concludes that the junction design of the axial port and chamber offers potential for improvement of fluidic diode performance.