• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.90-96
• /
• 2008

Engineered mixtures composed of rigid sand particles and soft rubber particles are tested to investigate their behavior with strain level. Mixtures are prepared with different volumetric sand fractions (sf) to identify response using small strain resonant column, intermediate strain oedometer, and large strain direct shear tests. The small strain shear modulus and damping ratio are determined with volumetric sand fractions. The asymmetric frequency response curve increases with decreasing sand fraction. Linear responses of shear strain and damping ratio with shear strain are observed at the mixture of sf=0.2. Vertical strain increases with decreasing sand fraction. Mixtures with $04.{\leq}sf{\leq}0.6$ show the transitional stress-deformation behavior from rubber-like to sand-like behavior. The friction angle increases with the sand fraction and no apparent peak strength is observed in mixture without sf=1.0.

• 대한기계학회논문집B
• /
• 제20권12호
• /
• pp.4053-4061
• /
• 1996

Internal flow characteristics within Y-jet atomizers and the local drop size distribution and cross-sectional averaged drop size at the outside were investigated with the liquid and air injection pressures, mixing port length of atomizers, and the liquid properties taken as parameters. To examine the effect of the liquid viscosity, glycerin-water mixtures were used in this study. The liquid viscosity plays only a minor role in determining the internal flow pattern and the spatial distribution shape of drops, but the drop sizes themselves generally increase with increasing of the liquid viscosity. An empirical correlation for the liquid discharge coefficient at the liquid port was deduced from the experimental results; the liquid discharge coefficient strongly depends on the liquid flow area at the mixing point which is proportional to the local volumetric quality(.betha.$_{Y}$), and the volumetric quality was included in the correlation. Regardless of the value of the liquid viscosity, the compressible flow through the gas port was well represented by the polytropic expansion process(k=1.2), and the mixing point pressure could be simply correlated to the aspect ratio( $l_{m}$/ $d_{m}$) of the mixing port and the air/liquid mass flow rate ratio( $W_{g}$/ $W_{f}$) as reported in the previous study.udy.udy.y.

• 한국물환경학회지
• /
• 제22권2호
• /
• pp.288-293
• /
• 2006

Basic investigations have been carried out for the solvent extraction of silver contained in the waste photographic fixing solution using D2EHPA as an extractant. Extraction experiments were conducted using artificial waste solution which was made by dissolving $AgNO_3$ in distilled water along with actual waste fixing solution. For artificial waste solution, the extraction of silver was found to occur very rapidly at the initial stage of extraction. In addition, more silver was extracted as the volumetric ratio between aqueous phase and organic phase was decreased. The volumetric ratio of organic extractant to diluent was also taken as an influential variable and the extracted amount of silver was observed to decrease with temperature. The characteristics of silver extraction for actual fixing solution was generally similar to that for artificial waste solution. Regarding the kinetic analysis, the extraction of silver contained in the actual solution was observed to follow a first order reaction.

• Korean Chemical Engineering Research
• /
• 제55권1호
• /
• pp.99-106
• /
• 2017

본 연구에서는 인도네시아 저등급 석탄인 Kideco탄을 이용하여 질소 분위기 하에 등온상태에서 촤(char)를 생성한 후 반응가스(스팀,이산화탄소)를 주입하여 합성가스를 생성하는 가스화를 진행하였다. 온도가 반응속도에 미치는 영향을 알아보기 위해 $850^{\circ}C$ 이하의 운전온도(700, 750, 800, $850^{\circ}C$)에서 반응을 진행하였다. 촉매가 미치는 영향을 알아보기 위해 알카리계 촉매인 탄산칼륨과 금속촉매인 니켈을 이용하였으며 두가지 촉매의 혼합비율(1:9, 3:7, 5:5, 7:3, 9:1)을 다르게 하여 연구를 수행하였다. 탄산칼륨은 물리적 혼합을 통해 니켈은 이온교환법을 통해 준비하였다. 기-고체 반응 특성을 알아보기 위해 열중량분석기와 가스크로마토그래피를 통해 얻은 실험결과를 shrinking core model (SCM), volumetric reaction model (VRM), random pore model (RPM) and modified volumetric reaction model (MVRM)에 적용하여 비교하였다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2005년도 학술발표회 논문집
• /
• pp.345-352
• /
• 2005

The purpose of this study is to analyze the stress-strain behavior of confined concrete columns with rectangular section. Uniaxial concentric loading tests of nineteen concrete columns with rectangular section ($150{\times}100$, $250{\times}100$, $350{\times}100\;mm$) were conducted. The main variables are transverse reinforcement volumetric ratio and spacing, cross tie arrangement, cross-section aspect ratio, and concrete strength. From the present experiments, it was found that the increase of transverse reinforcement ratio increases the maximum stress and ductility ratio and the reduction of the spacing of transverse reinforcement also increases the ductility and effective confinement. The increase of the aspect ratio of the cross-section does not influence much the stress-strain behavior of rectangular columns within the aspect ratio range of 3.5. The effect of concrete strength on ductility is also discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.790-795
• /
• 2001

Since the characteristics of combustion and pollutant in Diesel engines were mainly affected by the characteristics of in-cylinder gas flow and fuel spray, an understanding of those was essential to the design of the D.I. Diesel engines. The improvement of volumetric efficiency of air charging into combustion chamber is a primary requirement to obtain better mean effective pressure of an engine. Since the air resistances in intake and exhaust flow passages, valve lift and valve shape influence greatly to the volumetric efficiency, it is very important to investigate the flow characteristics of intake and exhaust port which develops air motion in the combustion chamber. This paper presents the results of an experimental investigation of steady flow through the various kinds of commercial cylinder head ports, and the development procedures of HHI's H21/32 prototype cylinder head ports.

• 한국인쇄학회지
• /
• 제14권1호
• /
• pp.17-29
• /
• 1996

N-substituted acrylamide hydrogel is reported to have the feature of bing transparent and sensitive enough to response to a temperature stimulus below the temperature of phase transition. Especially at the near of 35 C it becomes shrunk and opaque very quickly. It has also the characteristic of reversing swelling and shrinking. The experiment showed that it is possible to produce a functional gel of super water absorption with the process of free radical polymerizing PVA(polyvinylalcohol) and PAA(polyacrylamide), and crosslinking. The ratio of shrinking and swelling caused by copolymerization rises 10% to 80% at the each temperature of 20 C, 30 C, 40 C, respectively. Phase transition temperature of this gel by copolymerization is50 C while that of ordinary N-substituted acrylamides is between 32~35 C. This temperature reaches the rearing limit of animals and plants so that volumetric transition polymer gel can be ulilized in varying fields such as agriculture/gardening which are water-using field, on-off switch sensing temperature and volumetric variation, processing of liquid wastes and civil engineering works, architecture and electronics. We have no doubt that this material will be the high-functional resin in the hi-tech age of the near future.

• Journal of Advanced Marine Engineering and Technology
• /
• 제17권4호
• /
• pp.11-19
• /
• 1993

The experimental study was carried out to investigate the stability and the performance characteristics of the aero-valved pulsating combustion system with maximum operating capacity of 60KW. The effect of geometry of combustion system on the stable condition, the flammability limit, the total pressure oscillation amplitude, and the operating frequency can be identified, and the maximum turn-down-ratio is obtained up to 3.3. The total pressure oscillation amplitude can be controlled by tunning the length of the air inlet pipe. The empirical equation with which the operating frequency can be approximated is proposed and the discrepancy is within 5%. The volumetric efficiency is identified to be one of the important parameters determining the upper flammability limit and the maximum value of which is approximately 22%.

• 대한기계학회논문집B
• /
• 제37권9호
• /
• pp.847-854
• /
• 2013

본 연구는 환형 노즐 이젝터를 이용하여 수평방향 폭기공정의 혼합유동 및 산소전달 특성에 대한 실험적 연구를 목표로 한다. 실험변수는 이젝터 피치와 가압수 유량이며, 측정된 유량과 압력을 이용하여 유량비, 수두비 및 효율을 계산하였다. 이적터에서 분출된 혼합유동의 가시화를 통해 정성적 거동을 고찰하였으며, 용존산소량을 측정하여 총괄 산소전달계수를 도출하였다. 이젝터에서 분출된 혼합유동은 가압수의 운동량과 유입된 공기기포의 미립화에 따라 부력분류 또는 수평분류의 거동을 나타내었다. 기포의 크기에 기인하는 부력과 가압수의 운동량에 지배되는 혼합유동의 도달거리는 가압수와 공기기포의 접촉 면적 및 시간에 크게 영향을 미치기 때문에 산소전달률의 중요한 변수임을 유추할 수 있다.

• 환경위생공학
• /
• 제12권3호
• /
• pp.95-102
• /
• 1997

The process which can stabilize water quality of treatment and improve nitrogen removal rate under the condition of high organic loading was developed by charging fibrous HBC media to single sludge nitrification-denitrification process. This process was operated easier, minimized the treatment cost, and shortened the retention time. To improve T-N removal rate, a part of nitrifing liquid at aerobic zone was recycled to anoxic zone by approximate internal recycle ratio. The experimental results are as follows ; T-N removal efficiency in the organic volumetric loading 0.14-0.19 kg/COD/m$^{3}$·d was obtained asmaxium of 85% at internal recycle ratio 2.5 and in more ratio than this it was decreased. Organic removal efficiency was about 91% under the overall experimental conditions and not influenced by recycle ratio.