• 한국재료학회지
• /
• 제20권6호
• /
• pp.331-337
• /
• 2010

A highly porous Biphasic Calcium Phosphate (BCP) scaffold was fabricated by the sponge replica method with a microwave sintering technique. The BCP scaffold had interconnected pores ranging from $80\;{\mu}m$ to $1000\;{\mu}m$, which were similar to natural cancellous bone. To enhance the mechanical properties of the porous scaffold, infiltration of polycaprolactone (PCL) was employed. The microstructure of the BCP scaffold was optimized using various volume percentages of polymethylmethacrylate (PMMA) for the infiltration process. PCL successfully infiltrated into the hollow space of the strut formed after the removal of the polymer sponge throughout the degassing and high pressure steps. The microstructure and material properties of the BCP scaffold (i.e., pore size, morphology of infiltrated and coated PCL, compressive strength, and porosity) were evaluated. When a 30 vol% of PMMA was used, the PCL-BCP scaffold showed the highest compressive strength. The compressive strength values of the BCP and PCL-BCP scaffolds were approximately 1.3 and 2MPa, respectively. After the PCL infiltration process, the porosity of the PCL-BCP scaffold decreased slightly to 86%, whereas that of the BCP scaffold was 86%. The number of pores in the $10\;{\mu}m$ to $20\;{\mu}m$ rage, which represent the pore channel inside of the strut, significantly decreased. The in-vitro study confirmed that the PCL-infiltrated BCP scaffold showed comparable cell viability without any cytotoxic behavior.

• 한국재료학회지
• /
• 제17권6호
• /
• pp.318-322
• /
• 2007

Porous ${\beta}-tricalcium$ phosphate $({\beta}-TCP)$ bioceramic was fabricated by pressureless sintering using commercial HAp and different volume percentages of PMMA powders (30-60 vol.%). The range of spherical pore size was about $200-250\;{\mu}m$ in diameter. By increasing the PMMA content, the number of pores and their morphology were dramatically changed as well as decreased the material properties. In case of using 60 vol.% PMMA content, network-type pores were found, due to the necking of the PMMA powders. The values of relative density, elastic modulus, bending strength and hardness of the 60 vol.% PMMA content sample, sintered at $1500^{\circ}C$, were about 46%, 22.2 GPa, 5MPa and 182 Hv respectively. Human osteoblast-like MG-63 cells and osteoclast-like Raw 264.7 cells were well grown and fully covered all of the porous ${\beta}-TCP$ bodies sintered at $1500^{\circ}C$.

• 한국식품조리과학회지
• /
• 제23권1호통권97호
• /
• pp.41-49
• /
• 2007

The substitution effects of whey protein isolate(WPI) for egg in the preparation of sponge cake were determined by objective and subjective tests. Milk whey is drained from milk curd as a by-product of cheese manufacture. Whey protein is known as a good nutritional source and a functional material for many processed foods, especially baked goods. WPI contains above 90% whey protein. The specific gravity and viscosity of sponge cakes tend to be affected by WPI substitution. The cooking loss of sponge cakes with WPI substituted for egg(abbreviated as WPI cake) during oven baking was smaller than that made with egg(abbreviated as egg cake) and the specific loaf volume of WPI cake was larger than that of egg cake. The number of pores was highly increased and the size of pores was more uniformly and finely distributed in the cross section of WPI cake than those of egg cake, as observed by scanning electron microscopy(SEM). The hardness, gumminess and chewiness of WPI cake made with 10-20% WPI substitution were the lowest among all the tested cakes, including egg cake, thereby confirming the considerable improvement in their cake qualities. By the results of sensory evaluation, appearance, pore uniformity, softness, chewiness, moistness, flavor, mouth feeling, and overall acceptability of 10-20% WPI substitute cakes were evaluated as being significantly superior to those of all other cakes(p<0.05). These results support the better physicochemical characteristics and sensory evaluations of sponge cake prepared with 10-20% of WPI substitution for egg.

• 동아시아식생활학회지
• /
• 제24권2호
• /
• pp.190-200
• /
• 2014

In this study, the antioxidant activity and quality characteristics of the Korean traditional food jeung-pyun made with ju-bak powder were investigated. Jeung-pyun added with 10% ju-bak powder had a total polyphenol content of 54.27%, DPPH free radical scavenging activity of 91.98%, reducing power of 0.51% and SOD-like antioxidant activity of 18.21%. Jeung-pyun added with ju-bak powder had a moisture content of 52.65 to 46.94%, crude fat content of 1.61 to 1.29%, crude protein content of 3.50 to 4.66%, crude ash content of 0.68 to 0.82% and dietary fiber content of 0.12 to 1.46%. Ju-bak powder added with jeung-pyun had a pH level from 4.86 to 4.39. As ju-bak content increased, the pH decreased significantly. Color L value were 78.82 to 68.67. As ju-bak content increased, the Color L value content decreased significantly; a value ranged from -1.89 to 0.69 and b value from 2.99 to 14.25. As ju-bak content increased, the color content significantly increased. As ju-bak content increased, the volume significantly decreased (ranged from 42.50 to 30.00 mL), hardness, gumminess and chewiness significantly increased, and cohesiveness significantly decreased. From SEM, as ju-bak content increased, the pores merged and collapsed, whereas the number of pores decreased and pore size became larger. Sensory evaluation of color, flavor, taste, texture, appearance, cell uniformity and overall acceptability for various levels of ju-bak powder showed that 10% had the highest acceptability. Therefore, 10% ju-bak power added with jeung-pyun has both high antioxidant capacity and sensory acceptability.

• 한국재료학회지
• /
• 제22권2호
• /
• pp.66-70
• /
• 2012

Ti-Ni alloys are widely used in numerous biomedical applications (e.g., orthodontics, cardiovascular science, orthopaedics) due to their distinctive thermomechanical and mechanical properties, such as the shape memory effect, superelasticity and low elastic modulus. In order to increase the biocompatibility of Ti-Ni alloys, many surface modification techniques, such as the sol-gel technique, plasma immersion ion implantation (PIII), laser surface melting, plasma spraying, and chemical vapor deposition, have been employed. In this study, a Ti-49.5Ni (at%) alloy was electrochemically etched in 1M $H_2SO_4$+ X (1.5, 2.0, 2.5) wt% HF electrolytes to modify the surface morphology. The morphology, element distribution, crystal structure, roughness and energy of the surface were investigated by scanning electron microscopy (SEM), energy-dispersive Xray spectrometry (EDS), X-ray diffractometry (XRD), atomic force microscopy (AFM) and contact angle analysis. Micro-sized pores were formed on the Ti-49.5Ni (at%) alloy surface by electrochemical etching with 1M $H_2SO_4$+ X (1.5, 2.0, 2.5) wt% HF. The volume fractions of the pores were increased by increasing the concentration of the HF electrolytes. Depending on the HF concentration, different pore sizes, heights, surface roughness levels, and surface energy levels were obtained. To investigate the osteoblast adhesion of the electrochemically etched Ti-49.5Ni (at%) alloy, a MTT test was performed. The degree of osteoblast adhesion was increased at a high concentration of HF-treated surface structures.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.350-352
• /
• 2009

The effect of porosity on the high-cycle fatigue properties of Al-Si-Mg casting aluminum alloys was investigated in this study. Microstructure examination, tensile and high-cycle fatigue test were conducted on both Al-Si-Mg casted (F) and heat-treated (T6) conditions. Porosity characteristics on the fracture surfaces of fatigue-tested samples were examined using SEM and image analysis. The microstructure observation results showed that eutectic Si particles were homogeneously dispersed in the matrix of the Al-Si-Mg casting alloys, but there were porosities formed as cast defects. The high-cycle fatigue results indicated that the fatigue strength of the 356-T6 alloy was higher than that of the 356-F alloys because of the significant reduction in volume fraction of pores by heat treatment. The SEM fractography results showed that porosity affected detrimental effect on the fatigue life: 80% of all tested samples fractured as a result of porosity which acted as the main crack initiation site. It was found that fatigue life decreased as the size of the surface pore increased. A comparison was made between surface pore and inner pore fur its effect on the fatigue behavior. The results showed that the fatigue strength with the inner pores was higher than that of the surface pore.

• 소성∙가공
• /
• 제18권4호
• /
• pp.296-303
• /
• 2009

The effect of porosity on the high-cycle fatigue properties of Al-Si-Mg casting aluminum alloys was investigated in this study. Microstructure examination, tensile and high-cycle fatigue test were conducted on both Al-Si-Mg casted (F) and heat-treated (T6) conditions. Porosity characteristics on the fracture surfaces of fatigue-tested samples were examined using SEM and image analysis. The microstructure observation results showed that eutectic Si particles were homogeneously dispersed in the matrix of the Al-Si-Mg casting alloys, but there were porosities formed as cast defects. The high-cycle fatigue results indicated that the fatigue strength of the 356-T6 alloy was higher than that of the 356-F alloys because of the significant reduction in volume fraction of pores by heat treatment. The SEM fractography results showed that porosity affected detrimental effect on the fatigue life: 80% of all tested samples fractured as a result of porosity which acted as the main crack initiation site. It was found that fatigue life decreased as the size of the surface pore increased. A comparison was made between surface pore and inner pore for its effect on the fatigue behavior. The results showed that the fatigue strength with the inner pores was higher than that of the surface pore.

• 한국분말재료학회지
• /
• 제21권4호
• /
• pp.266-270
• /
• 2014

Metal foams have a cellular structure consisting of a solid metal containing a large volume fraction of pores. In particular, open, penetrating pores are necessary for industrial applications such as in high temperature filters and as a support for catalysts. In this study, Fe foam with above 90% porosity and 2 millimeter pore size was successfully fabricated by a slurry coating process and the pore properties were characterized. The Fe and $Fe_2O_3$ powder mixing ratios were controlled to produce Fe foams with different pore size and porosity. First, the slurry was prepared by uniform mixing with powders, distilled water and polyvinyl alcohol(PVA). After slurry coating on the polyurethane(PU) foam, the sample was dried at $80^{\circ}C$. The PVA and PU foams were then removed by heating at $700^{\circ}C$ for 3 hours. The debinded samples were subsequently sintered at $1250^{\circ}C$ with a holding time of 3 hours under hydrogen atmosphere. The three dimensional geometries of the obtained Fe foams with an open cell structure were investigated using X-ray micro CT(computed tomography) as well as the pore morphology, size and phase. The coated amount of slurry on the PU foam were increased with $Fe_2O_3$ mixing powder ratio but the shrinkage and porosity of Fe foams were decreased with $Fe_2O_3$ mixing powder ratio.

• 한국재료학회지
• /
• 제26권8호
• /
• pp.449-453
• /
• 2016

$HA(hydroxyapatite)/{\beta}-TCP$ (tricalcium phosphate) biomaterial (BCP; biphasic calcium phosphate) is widely used as bone cement or scaffolds material due to its superior biocompatibility. Furthermore, $NH_4HCO_3$ as a space holder (SH) has been used to evaluate feasibility assessment of porous structured BCP as bone scaffolds. In this study, using a spark plasma sintering (SPS) process at 393K and 1373K under 20MPa load, porous $HA/{\beta}-TCP$ biomaterials were successfully fabricated using $HA/{\beta}-TCP$ powders with 10~30 wt% SH, TiH2 as a foaming agent, and MgO powder as a binder. The effect of SH content on the pore size and distribution of the BCP biomaterial was observed by scanning electron microscopy (SEM) and a microfocus X-ray computer tomography system (SMX-225CT). The microstructure observations revealed that the volume fraction of the pores increased with increasing SH content and that rough pores were successfully fabricated by adding SH. Accordingly, the cell viabilities of BCP biomaterials were improved with increasing SH content. And, good biological properties were shown after assessment using Hanks balanced salt solution (HBSS).

• 대한토목학회논문집
• /
• 제4권2호
• /
• pp.25-33
• /
• 1984

활성탄(活性炭)의 입경변화(粒徑變化)가 trihalomethane의 흡착(吸着)에 미치는 영향(影響)에 관하여 실험적(實驗的)으로 연구(硏究)하였다. 실험(實驗)에 사용(使用)된 활성탄(活性炭)은 평균입경(平均粒徑)이 0.73mm에서 2.03mm까지의 4종류(種類)이었으며 이들에 대하여 물리적(物理的) 특성(特性)을 조사(調査)하고 trihalomethanedml 흡착능력(吸着能力)을 등온흡착실험(等溫吸着實驗)과 micro-column 실험(實驗)을 통해 밝혀냈다. 입경(粒徑)의 증가(增加)에 따라 비표면적(比表面積)이 감소(減少)하였고 활성탄(活性炭) 내부공극(內部空隙)의 반경(半徑)이 크게 증가(增加)하였다. 또한 큰 입자(粒子)의 경우에는 공극(空隙)의 크기가 넓게 분포(分布)하였다. Trihalomethane의 흡착(吸着)은 Freundlich 공식(公式)에 의해 잘 표현(表現)되었고 입경증가(粒徑增加)에 따라 흡착능력(吸着能力)의 감소(減少)가 뚜렷하게 나타났다. Micro-column 실험결과(實驗結果)와 모형(模型)의 Simulation으로부터 물질도달계수(物質導達係數)와 내부표면광산계수(內部表面壙散係數)를 산정(算定)하였다. 입경변화(粒徑變化)에 따른 계수(係數)의 변화(變化)는 무시(無視)할 수 있었으며 입경변화(粒徑變化)에 따른 효율(効率)의 차이(差異)는 주로 흡착능력(吸着能力)의 차이(差異)에서 오는 결과(結果)로 판단(判斷)된다.