• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.188-193
• /
• 2006

Synthesis of Boehmite particles were performed through the precipitation of aluminium nitrate ($Al_{3}(NO_{3})_3{\cdot}9H_{2}O$) with ammonia water ($NH_{4}OH$) by changing solution pH, mixing procedure, temperature, and feeding flux. The influence of the synthesis condition, which affected on the pH range of the Boehmite formation, particle morphology and pore property, was investigated. The Boehmite particles were formed in the reaction solution of pH 7.5~9. The particles prepared by P2jet type which maintained the pH uniformly during the precipitation resulted in homogeneous particles and pores because of the constant concentration of the reacted ion in the solution. It was resulted in the improvement of the specific surface area and pore volume of the particle at the same time. With the increasing of temperature and the decreasing of the feeding flux, it was occurred the large specific surface area and pore volume. Also it was presented the fibrillar shaped particles upper $60^{\circ}C$ of the reaction temperature. In this study, the optimal condition of the porous Boehmite was in P2jet type with $90^{\circ}C$ of reaction temperature and 2.5 mL/min of the feeding flux. At this time, the specific surface area, pore volume, and average pore size was $385.46m^2/g$, 1.0252 mL/g, 10 nm, respectively.

• Clean Technology
• /
• v.26 no.2
• /
• pp.131-136
• /
• 2020

Biomass bamboo charcoal is utilized as anode for lithium-ion battery in an effort to find an alternative to conventional resources such as cokes and petroleum pitches. The amorphous phase of the bamboo charcoal is partially converted to graphite through a low temperature graphitization process with iron oxide nanoparticle catalyst impregnated into the bamboo charcoal. An optimum catalysis amount for the graphitization is determined based on the characterization results of TEM, Raman spectroscopy, and XRD. It is found that the graphitization occurs surrounding the surface of the catalysis, and large pores are formed after the removal of the catalysis. The formation of the large pores increases the pore volume and, as a result, reduces the surface area of the graphitized bamboo charcoal. The partial graphitization of the pristine bamboo charcoal improves the discharge capacity and coulombic efficiency compared to the pristine counterpart. However, the discharge capacity of the graphitized charcoal at elevated current density is decreased due to the reduced surface area. These results indicate that the size of the catalysis formed in in-situ graphitization is a critical parameter to determine the battery performance and thus should be tuned as small as one of the pristine charcoal to retain the surface area and eventually improve the discharge capacity at high current density.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.1
• /
• pp.33-40
• /
• 2024

The volume of shells, a prominent form of marine waste, is steadily increasing each year. However, a significant portion of these shells is either discarded or left near coastlines, posing environmental and social concerns. Utilizing shells as a substitute for traditional aggregates presents a potential solution, especially considering the diminishing availability of natural aggregates. This approach could effectively reduce transportation logistics costs, thereby promoting resource recycling. In this study, we explore the feasibility of employing wasted shell aggregates in 3D concrete printing technology for marine structures. Despite the advantages, it is observed that 3D printing concrete with wasted shells as aggregates results in lower strength compared to ordinary concrete, attributed to pores at the interface of shells and cement paste. Microstructure characterization becomes essential for evaluating mechanical properties. We conduct an analysis of the mechanical properties and microstructure of 3D printing concrete specimens incorporating wasted shells. Additionally, a mix design is proposed, taking into account flowability, extrudability, and buildability. To assess mechanical properties, compression and bonding strength specimens are fabricated using a 3D printer, and subsequent strength tests are conducted. Microstructure characteristics are analyzed through scanning electron microscope tests, providing high-resolution images. A histogram-based segmentation method is applied to segment pores, and porosity is compared based on the type of wasted shell. Pore characteristics are quantified using a probability function, establishing a correlation between the mechanical properties and microstructure characteristics of the specimens according to the type of wasted shell.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.5
• /
• pp.35-40
• /
• 2012

In this study, adsorption characteristics of expanded graphite (EG) were investigated by a series of batch adsorption tests using p-Xylene as a model volatile organic compounds (VOCs). After acid treatment, graphite were expanded at various temperature from $600^{\circ}C$ to $1000^{\circ}C$ for one minute. The optimal temperature was $800^{\circ}C$, where the expansion ratio reached 195 times of original volume. The BET specific surface area of EG was $92.4m^2/g$, which was only 1/10 of granular activated carbon (GAC), however the adsorption of p-Xylene by EG was almost completed within 5 minutes while that of GAC continued for 7 days because the majority of pores of EG was consisted with meso- and macro-pores. According to the Langmuir isotherm analysis, the maximum specific adsorption of p-Xylene onto EG was 24.0 mg/L with the adsorption constant of 7.94. In conclusion, the adsorption capacity of EG was much less than that of GAC due to the significantly lower specific surface area, but the first order kinetic constant was more than 500 times larger than GAC. Overall, EG might be effective where the fast adsorption is required.

• Resources Recycling
• /
• v.19 no.1
• /
• pp.33-39
• /
• 2010

The spheric sintered body with $6{\pm}2mm$ diameter was manufactured in a rotary kiln at $1125^{\circ}C$/15 min using green body formed by pelletizing the batch powder composing of coal bottom ash produced from power plant and dredged soil by 70:30, wt%. And the physical properties of sintered body (BD) were analyzed to confirm the possibility for applying to an absorbent to restore a contaminated soil. The sintered body had a giant pore above 100 ${\mu}m$ and a fine pore below 10 ${\mu}m$, and bulk density was 1.4. Also its specific surface area, porosity and void proportion were $12.0m^2/g$, 30.1% and 38.2% respectively. The crushed body (BD-C), produced by crushing a BD specimen into an irregular shape with a aspect ratio of about 2, was similar to BD specimen at bulk density and pore size distribution. But it had superior values of specific surface area, porosity and void proportion compared with BD specimen owing to a decreased apparent volume due to conversion of closed pore existed at interior of BD to open pore during a crushing process. The IEP of sintered body occurred at about pH=5, so the optimum pH condition of reacting aqueous solution could be known before bonding a microbe to the sintered body. Hence, the optimum void proportion and porosity of an absorbent can be obtained by appropriate mixing a BD with BD-C from the base data calculated in this study.

• Journal of the Korean Ceramic Society
• /
• v.34 no.3
• /
• pp.225-232
• /
• 1997

The performance characteristics of high rate discharge LiSOCl2 cells are highly affected by carbon cathode. During the cell discharge, SOCl2 reduction takes place at the porous carbon cathode, resulting in the precipitation of reaction products, mainly LiCl, within the pores of the substrate. This leads to eventual passivation of the cathode surface and resulting cell failure. To improve the cathode performance, we ex-amined discharge reactions of cathodes (half-cell, 50 mA/$\textrm{cm}^2$ constant current) with various surface density and thickness. The carbon cathode with the optimum capacity for our application is surface density 0.04 g/$\textrm{cm}^2$ and thickness 1.4mm carbon. The carbon cathode with surface density 0.04g/$\textrm{cm}^2$ and thickness 1.4 mm exhibits decreased polarization, increased discharge duration time and capacity (Ah/$\textrm{cm}^2$) as compared with that with surface density 0.04g/$\textrm{cm}^2$ and thickness 0.8mm. The porosities analyses on the two carbon cathodes show that total pore volume of the carbon cathode with thickness 1.4 mm is larger than that with thickness 0.8mm. The increased volume of mesopores (0.05$\mu$m~0.5$\mu$m) and macropores(>0.5$\mu$m) is ob-served with the carbon cathode with thickness 1.4mm as compared with that with thickness 0.8mm, which can be related with the observed capacity increase. We observed LiCl crystals, cubic crystallites and fused, plate-like aggregates, and some elemental S as discharge products by EDS and XRD.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.6 no.6
• /
• pp.49-55
• /
• 2003

Total phosphorous removal rate was examined of a subsurface-flow treatment wetland system which was constructed on floodplain in the down reach of the Kwangju Stream in Korea from May to June 2001. Its dimensions were 29 meter in length, 9 meter in width and 0.65 meter in depth. A bottom layer of 45 cm in depth was filled with crushed granite with about 15~30 mm in diameter and a middle layer of 10 cm in depth had pea pebbles with about 10 mm in diameter. An upper layer of 5 cm in depth contained course sand. Reeds(Phragmites australis) were transplanted on the surface of the system. They were dug out of natural wetlands and stems were cut at about 40 cm height from their bottom ends. Water of the Kwangju Stream flowed from a submerged dam into it via a pipe by gravity flow and treated effluent was funneled back into the Stream. The number of reed stems increased from 80 stems/$m^2$ in July 2001 to 136 stems/$m^2$ in September 2001. The hight of stems was 44.2 cm in July 2001 and 75.3 cm in September 2001. The establishment of reeds at early operating stage of the system was good. Volume and water quality of inflow and outflow were investigated from July 2001 through December 2001. The average inflow was 40 $m^3$/day and hydraulic detention time was about 1.5 days. The concentration of total phosphorous n influent and effluent was 0.83 and 0.33 mg/L, respectively. The removal rate of total phosphorous averaged about 60%. The removal efficiency was slightly higher, compared with that of subsurface-flow wetlands operating in North America, whose retention rate of total phosphorous was reported to be about 56%. The good abatement rate could be attributed to sedimentation of particle phosphorous in pores of the media and adsorption of phosphorous to the biofilm developed on the surface of them. Increase of standing density of reeds within a few years will develop root zones which may lead to increment in the phosphorous retention rate.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.39 no.4
• /
• pp.98-105
• /
• 1997

Compacted clay materials are often used to form barriers for waste disposal by means of landfill. The performance of clay barrier depends on its permeability characteristics under the site environments. The study discusses permeability characteristics of 4 types of permeants through a compacted clayey soil. Permeabilities are measured using the modified rigid-wall permeater and with water, PEG, Ethanol, and TCE, ranging 80 to 3.4 of dielectric constants. Results of the study are as follows : 1) Absolute permeabilities of Ethanol and TCE that their dielectric constants are lower than that of water are $K=1.0{\times} 10^{-12} cm^2$, and $5.8{\times} 10^{-12} cm^2$, respectively, that is, 1.67, and 9.67 times of permeability of water, respectively. Absolute permeability and dielectric constant of water are $K=6{\times} 10^{-13} cm^2$, and 80, respectively. 2) Changes in absolute permeability of Ethanol and TCE converge to a constant after 3.5 pore volume of permeant flows through the clay sample. This can be explained that diffuse double layer of clay is no longer reacted with permeants and contracted their pores. However there is no change in absolute permeability when water is used as a per-meant. 3) It is found that absolute permeability in reversely proportional to the value of dielectric constant of the permeants. Change in absolute permeability of the permeants with 40 or over of dielectric constant is not significant. However change in absolute permeability of the permeant with 30 or lower dielectric constant is abruptly increased. 4) A lower absolute permeability of PEG is found because of its high viscosity.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.3
• /
• pp.29-36
• /
• 2001

This paper was made to evaluate the effect of the blending ration of GCC and No. 1 clay on the printability by investigating the structure of pore such as the pore rate, the number of pores, pore size and distribution of coated paper. The coated structure is mainly depended on the results of correlation between pigment and binder. It means that the structure of the pore occurred is chiefly affected by the blending ratio of GCC and No. 1 clay. This physical properties of the pore have a close relation with ink set-off associated with the drying rate and the penetration in ink into base paper and with printing gloss. Therefore it was needed to find out how the pore structure and the printability will be changed by modifying the blending ratio of GCC and No. 1 clay to vary the pore structure of coated paper. Below are the results of measurement: As the blending ratio of clay going up, water retention, sedimentation volume. smoothness, and paper gloss were increased, but relatively brightness and opacity were decreased. Pore rate was the highest at the blending ratio of No. 1 clay to GCC, 70:30. In this case, average pore radius was also increased. Ink receptivity and K&N ink receptivity were improved with the increase of the blending ratio of GCC, where was, ink setting was vice versa. No difference was observed in the weight of ink, but ink repellance decrease with the decrease of blending ratio of GCC.

• International Journal of Concrete Structures and Materials
• /
• v.7 no.2
• /
• pp.95-110
• /
• 2013

We report various synchrotron radiation laboratory based techniques used to characterize cement based materials in nanometer scale. High resolution X-ray transmission imaging combined with a rotational axis allows for rendering of samples in three dimensions revealing volumetric details. Scanning transmission X-ray microscope combines high spatial resolution imaging with high spectral resolution of the incident beam to reveal X-ray absorption near edge structure variations in the material nanostructure. Microdiffraction scans the surface of a sample to map its high order reflection or crystallographic variations with a micron-sized incident beam. High pressure X-ray diffraction measures compressibility of pure phase materials. Unique results of studies using the above tools are discussed-a study of pores, connectivity, and morphology of a 2,000 year old concrete using nanotomography; detection of localized and varying silicate chain depolymerization in Al-substituted tobermorite, and quantification of monosulfate distribution in tricalcium aluminate hydration using scanning transmission X-ray microscopy; detection and mapping of hydration products in high volume fly ash paste using microdiffraction; and determination of mechanical properties of various AFm phases using high pressure X-ray diffraction.