• Journal of the Korea Concrete Institute
• /
• v.17 no.5 s.89
• /
• pp.695-702
• /
• 2005

It is known that latex-modified concretes were increased their durability and permeability by added latex. The purpose of this study was to analysis the air void systems in latex-modified concretes using a reasonable and objective image analysis method with main experimental variables such as water-cement ratios, latex contents(0%, 15%) and cement types(ordinary portland cement, high-early strength cement and very-early strength cement). The results are analyzed spacing factor, air volume after hardened, air distribution and structure. Also, air void systems and permeability of latex-modified concretes were compared with correlation. The results are as follows; The same w/c ratio LMC showed better air entraining effect than OPC with AE water reducer. The VES-LMC showed that the number of entrained air below $100{\mu}m$ increased more than four times. In the HES-LMC, micro entraining air having range from 50 to $500{\mu}m$ increased above 7 times without antifoamer. Though spacing factor was measured low, latex-modified concretes were showed that permeability was good. It is considered that air void system does not have an effect on the property of latex-modified concretes but latex film is more influenced in the their durability.

• Radiation Oncology Journal
• /
• v.6 no.1
• /
• pp.93-99
• /
• 1988

Some modern accerelators provide a dual energy for photon beam treatment. The main advantages of dual energy in the treatment of rectosigmoid or rectal cancer are as fellows. 1. Dose in the critical organ such as small intestine, bladder and genital organ are reduced. 2. Presacral and perineal area is fully covered. Dose distribution analysis such as calculation of dose in a target volume, isocenter, $D_{nax}$ and dose spectrum in any region of interest are possible. Examples of plan are given and results are discussed.

• Journal of Chest Surgery
• /
• v.31 no.2
• /
• pp.142-148
• /
• 1998

Video-assisted thoracic surgery(VATS) is emerging as a viable alternative to thoracotomy when surgical treatment of spontaneous pneumothorax is required. 20 patients with spontaneous pneumothorax underwent bullectomy between July 1995 and May 1996. The patients were divided into two groups : Control group ; the patients who received with mid-axillary approach(n=10), Experimental group ; the patients who received with VATS (n=10). The results were as follows ; 1. The total sex distribution was male predominance (male:female=17:3). Mean age of control group was 29.6$\pm$9.8 years and experimental group was 27.2$\pm$11.9 years. 2. The mean period of postoperative chest tube indwelling duration and hospital stay were 3.3$\pm$0.8 days and 7.9$\pm$1.2 days in control group and 2.1$\pm$0.9 days and 5.2$\pm$3.1 days in experimental group(p=0.005 and p=0.02). 3. The mean time of operation, vital signs and arterial blood gas analysis did not showed any statistical differences between the groups. 4. Percent recovery of tidal volume and forced vital capacity were significantly improved in experimental group comparing with control group (p<0.05). 5. The patients undergoing VATS experienced significantly less postoperative pain and limitation of motion. In conclusion, VATS is safe and offers the potential benefits of shorter postoperative hospital stays and less pain with cosmetic benefits.

• Geophysics and Geophysical Exploration
• /
• v.18 no.4
• /
• pp.223-231
• /
• 2015

Self-potential (SP) is sensitive to groundwater flow and there are many causes to generate SP. Among many mechanisms of SP, pore-fluid flow in porous media can generate potential without any external current source, which is referred to as electrokinetic potential or streaming potential. When calculating SP responses on the surface due to geothermal fluid within an engineered geothermal system (EGS) reservoir, SP anomaly is usually considered to be generated by fluid injection or production within the reservoir. However, SP anomaly can also result from geothermal water fluid within EGS reservoirs experiencing temperature changes between injection and production wells. For more precise simulation of SP responses, we developed an algorithm being able to take account of SP anomalies produced by not only water injection and production but also the fluid of geothermal water, based on three-dimensional finite-element-method employing tetrahedron elements; the developed algorithm can simulate electrical potential responses by both point source and volume source. After verifying the developed algorithm, we assumed a simple geothermal reservoir model and analyzed SP responses caused by geothermal water injection and production. We are going to further analyze SP responses for geothermal water in the presence of water production and injection, considering temperature distribution and geothermal water flow in the following research.

• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2010

To enhance the transport properties of gas separation membrane, we prepared 6FDA-6FpDA based polyimide membrane with PMMA-graft-silica nanoparticles. The silica was grafted PMMA which is miscible with 6FDA-based polyimide after surface treatment by 3-methacryloxypropyltrimethoxysilane ($\gamma$-MPS). The untreated silica/6FDA-6FpDA membrane showed greater permeability and less selectivity than PMMA-g-silica/6FDA-6FpDA due to its low dispersion. The transport properties of PMMA-g-silica/6FDA-GFpDA membrane were measured as a function of filler concentration. These membranes were evaluated using pure gases (He, $O_2$, $N_2$, $CO_2$). The increase in permeation was attributed to changes in the free volume distribution until 1 wt%. After 1 wt%, the permeability was decreased by excess silica which decreased effective area in polymer matrix. The selectivity was decreased with increasing permeability on the whole. However, the selectivity of $CO_2$ showed more enhance value.

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.2
• /
• pp.5-12
• /
• 2009

Soil samples from the King Sejong Station in Antarctic and Vladivostok were tested in the laboratory and specific gravity, compaction curve, grain size distribution were determined. The effect of temperature change on the thermal conductivity, unfrozen water content, compressive strength were investigated. In addition, the change of tensile strength with temperature of the soil from Vladivostok was measured. Samples for the compressive strength test and tensional strength test were prepared in a mould with a fixed volume to prevent swelling. Also the effects of temperature and water content change on those strength were compared. Results from the thermal conductivity test showed that thermal conductivity values for both soils was larger at temperatures below freezing than those above freezing. The unfrozen water content dropped rapidly within a temperature range of $0{\sim}-5^{\circ}C$ and then gradually decreased further $-20^{\circ}C$. Compressive strength test results showed various stress/deformation curves with a change in water content. Sandy soil of the King Sejong Station had a much larger strength than ice at an identical temperature, while clayey soil of Vladivostok had a smaller strength than ice in the initial stage, but showed a larger strength at temperatures belows $-15^{\circ}C$. Tensile strength tests revealed an increase in the strength with a decreasing temperature.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.287-297
• /
• 2019

Responding to the rapid delivery demands and variety of small-volume products through human resource-dependent logistics operations in online markets is difficult. Logistics robots in fulfillment centers are expected to increase due to difficulties in hiring workers and rising labor costs. Amazon operates more than 100,000 robots in its Fulfillment centers. Alibaba, DHL, and UPS are also introducing robot technology to improve the logistics efficiency. Logistics robots are being used actively in the fierce online market competition of the global distribution industry. On the other hand, Korea is relatively sluggish. To revitalize the introduction of logistics robots in Korea, it is necessary to examine the factors that influence acceptance. The description of acceptability was based on an expanded technology acceptance model that has been verified through various studies. Studies have shown that both the ease and usefulness of purchasing have significant effects, and that ease has the greatest effect. The more experience involved, the more innovative, the more positive. The usefulness was shown to be positive as the perceived risks are low, price efficiency is good, and social impact is greater. This study provides theoretical and practical implications for logistics robot development and marketing.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.329-336
• /
• 2000

Welding is a important technological method in mechanical engineering. $CO_2$MAG(metal active gas) welding means that metal part in double capstan drum for the inshore and costal vessels are joined by melting(with or without a filler material) or that new material is added to a metal part by melting. The thermal stresses appear due to a non-uniform temperature field, inhomogeneous material properties, external restraint and volume changes during phase transformations. In this study analysis the elasto-plastic thermal stresses distribution of welding part in double capstan drum for the inshore and costal vessels using finite element method (FBM). Therefore it calculates the numerical value that can be applied to the optimum design of welding parts and the shapes. The significant results obtained in this study are summarized as fellows. At early stage of the cooling after welding process, the abrupt thermal stresses gradient has been shown in the vicinity of welding part. In the thermal stresses analysis due to temperature gradient and heat shocking maximum stress was occurred of welding part and stresses were distributed from 54MPa~48MPa.

• Progress in Medical Physics
• /
• v.14 no.1
• /
• pp.8-14
• /
• 2003

The spinal cord dose is the one of the limiting factor for the radiation treatment of the head ＆ neck or the thorax region. It is not an easy task to maintain the spinal cord dose below tolerance and to keep the clinically acceptable dose to the PTV in this region. To overcome this problem, the spinal cord partial block technique (PBT) with the dynamic Multi-Leaf Collimator (dMLC) has been developed. This technique is an extension of the conventional treatment planning. In the beginning the beam directions are selected as same as the conventional treatment planning to encompass the PTV, then the partial block are designed to shield the spinal cord. The plan comparisons between the conventional therapy plan and the PTB plan were performed to evaluate the validity of this technique. The mean dose and the dose volume histogram (DVH) were used as the plan comparison indices. A series of quality assurance (QA) was performed to guarantee the reliable treatment. The QA consisted of the film dosimetry for the verification of the dose distribution and the point measurements. The PBT plan generated better results than the conventional treatment plan and it was proved to be useful for the H＆N region.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.38 no.1
• /
• pp.8-14
• /
• 1993

To investigate selection efficiency for protein content and hardness in a wheat breeding program, two crosses were made between soft wheat (SW) ‘Chokwang’ and hard wheat (HW) ‘Lancota’, and between HW ‘Suwon 210’ and SW ‘Atlas 66’. F2 progeny lines from the crosses were separated into 4 groups as HW + high protein (HP), HW + low protein (LP), SW + HP and SW + LP by measuring protein content and sedimentation value in F4 generation. The subsequent populations were tested for protein content, sedimentation value, mixogram pattern and bread quality. HP group selected from F4 again had a higher protein content in F5 generation than LP group, but there was no significant difference between two groups in F6 generation. In sedimentation value, the significant difference was recognizable only between the groups of HW + HP and. SW + LP. Plant based investigation in F6 revealed that the distribution pattern for protein content and sedimentation value shifted from the low to high by the four groups with the order of SW + LP, HW + LP, SW + HP, HW + HP. Such a trend was most noticeable in the progenies of the cross between ‘Suwon 210’ and ‘Atlas 66’. Mixogram pattern that shows flour characteristics differed greatly among the groups, indicating a high selection efficiency for the traits. Bread volume in F6 of HW + HP was found to be higher than that of SW + LP, only from the cross between ‘Suwon 210’ and ‘Atlas 66’.