• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.598-601
• /
• 2000

We investigated the fabrication of Si nanoparticle and $C_{60}$ thin films by pulsed laser ablation. As a result, we observed visible green photoluminescence spectra in the Si/C$_{60}$ multilayer films after laser annealing. It is considered that this green photoluminescence is occurred from SiC particles, which is produced reaction of Si nanoparticles with $C_{60}$ via laser annealing.ing.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.25 no.2
• /
• pp.368-382
• /
• 1998

The purpose of this study is to evaluate and compare the results of argon laser for 5 seconds, argon laser for 10 seconds, and visible light for 40 seconds photo-polymerization in compressive strength, microhardness, curing depth, temperature rising during polymerization, and polymerization shrinkage. Hybrid type composite resin(Z-100) and compomer(Dyract) were used to be compared. The compressive strength was measured by an Instron(1mm/min cross head speed) in 60 specimens and the microhardness of the surface was expressed by Vickers Hardness Number(VHN) in 30 specimens. The curing depth was evaluated comparing the different values of upper and lower VHN according to irradiation time and thickness for the light source polymerization in 60 specimens. The temperature rising during photopolymerization was observed by the temperature change with thermocouple sensitizer beneath 40 specimens at the argon laser for 10 seconds and visible light 40 seconds irradiation. The polymerization shinkage was evaluated by calculating the decrease of % volume by using a dilatometer in 30 specimens. The results were as follows ; 1. In the case of compressive strength, the argon laser polymerization groups were higher than visible light group in Z-100 (p<0.05). In Dyract, the argon laser 5 seconds group did not show a significant difference with the visible light 40 seconds group. The argon laser 10 seconds group showed the markedly low value when compared with other groups (p<0.05) 2. In microhardness, Z-100 was better than Dyract when comparing by VHNs (p<0.05); however, there was not a significant difference between two materials in the visible light 40 seconds group and the argon laser 10 seconds group. 3. In the study of curing depth, Z-100 showed the consistent polymerization in argon laser irradiation because there was no difference in the VHN decrease according to the thickness change. Over the thickness control, the results did not show a significant difference between visible light and argon laser group in Z-100; however, in the case of Dyract, the visible light 40 seconds group was better than the argon laser groups(p<0.05). 4. There was a significant difference between the two materials in temperature rising during polymerization (p<0.05), but not a significant difference between irradiation times, 5. There was not a significant difference between the two materials in polymerization shrink age. The argon laser 5 seconds group was smaller than the other groups (p<0.05). It could be concluded that Z-100 polymerization was recommended to use the argon laser for reduction of the irradiation time while Dyract was recommended to use the visible light polymerization.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.6
• /
• pp.917-922
• /
• 2013

In this paper, we propose a smoke detection system in order to detect a fire in a wide space, such as tunnel, airports using infra-red and visible laser. The proposed smoke detection system is composed of infra-red laser transmitter and receiver, visible laser and Zigbee wireless communication network. A visible laser is used to match transmitter and receiver and Zigbee network is utilized to propagate warnings of fire. If smoke is appeared between transmitter and receiver, received signals are decreased and it can be considered as occurring smoke. As IR laser transmitter and receiver are separated by long distance, it is difficult to match due to large variations caused by small change of direction. In this paper, it is proposed to match effectively using visible laser. When smoke is detected, warning informations are propagated by Zigbee network in the developed smoke detection system.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.2
• /
• pp.327-346
• /
• 1996

The purpose of this study was to evaluate the shear bond strengths, microhardness, compressive strength and contraction gap at the resin-tooth interface of two types of composite resins polymerized with visible light and argon laser sourse. The results from the present study can be summarized as follows ; 1. Resin samples polymerized either by argon laser or visible light did not show significant difference in their physical properties tested(p>.05). 2. The contraction gap at the resin tooth interface was found to be present in all samples but any significant difference between groups could not be established due to their variability. Although the superiority of argon laser over visible light in enhancing the physical properties of resin could not be elucidated in the present study, continous efforts are deemed to be worthwhile to investigate this area using different conditions and materials of experiment.

• Laser Solutions
• /
• v.12 no.1
• /
• pp.7-13
• /
• 2009

Engineering ceramics as sapphire are widely used in industry owing to their superior mechanical and corrosion properties. However, micromachining of sapphire is a considerable challenge due to its transparency. Recently, direct ablation of sapphire has been demonstrated with a visible laser pulse at sufficiently high laser intensity. In this work, the theoretical model for pulsed laser ablation of sapphire is suggested and numerical analysis is carried out using the model. Sapphire ablation begins with plasma generation by the laser interaction with surface defects, impurities and contaminations in the initial stage of machining. Subsequent absorption of the visible laser beam can be explained by three mechanisms: metalization of sapphire surface due to the EUV radiation from the hot plasma, increments of surface roughness and temperature-dependent absorption coefficient. Comparison of the computation results with experimental observation indicates that the proposed model of sapphire is reasonable.

• Korean Journal of Optics and Photonics
• /
• v.5 no.2
• /
• pp.278-285
• /
• 1994

We investigated the spectral characteristics for temperature and driving current change in visible laser diode. As a result of spectrum analysis, the ratio of frequency change for temperature and driving current change were about $33 GHz/^{\circ}C$, 6.6 GHz/mA in the region which was not mode hopping range. Compared to the sharp mode hopping in the near IR single mode AlGaAs lasers, the visible laser diode showed relatively broad multimode operation in the mode hopping region. We performed the experiment of injection-locking characteristics analysis for visible laser diode. Locking half bandwidth(LHBW) was measured 0~5.0 GHz for $0~25\muW$ input power and it was dependent on the input power. Also, LHBW for polarization angle was dependent on the difference of polarization angle between master laser and slave laser. The phase change of injection-locked output beam of the slave laser diode as a function of the drive current was measured in the interferometer which was composed of master laser and slave laser. The ratio of phase change with the slope of 5.0~1.3 rad/mA was obtained within injection-locking range for the change of $2~25\muW$ input power. power.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.2
• /
• pp.315-319
• /
• 2002

Visible surface-assisted desorption/ionization mass spectrometry (SALDI-MS) has been investigated for several small macromolecules deposited on the graphite plate using laser radiation at 532 nm where most of the macromolecules are transparent. The graphite surface functioned well as a photon absorbing material and an energy transfer mediator for visible light. The results show that visible SALDI is a much softer ionization technique than UV-MALDI and FAB-MS in our results with synthetic macromolecules, PPG, PPGMBE and cavitand molecules. For the SALDI of biomolecules, glycerol as a proton source was essential with the graphite plate. As in visible SALDI, the role division of the photon absorbing material and the cationization agent can provide a generality in mass spectrometric analysis of macromolecules compared with MALDI using the dual functional matrix.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.4
• /
• pp.840-858
• /
• 1996

The main purpose of this study was to evaluate the anticariogenic effect of argon laser. Histological observations on lesion initiation and progression were performed under the polarized microscope. The results from the present study can be summarized as follows; 1. The specimens of laser cured group were shown to have more irregular and discontinuous lesion body in general than visible light cured group with rather continuous positive birefringence. 2. With lesion initiation and progression, almost all the specimens showed deeper body of lesion with shallower intact surface zone in the visible light cured group than the laser cured group(p<0.05). When the comparision was made between the two argon laser cured groups, the single-cure group showed deeper lesion body and the shallower surface layer than double-cure group. 3. Based upon the above mentioned results of this study, it can be assumed that the use of argon laser in the procedure of resin polymerization may provide the child and adolescent patient population with anticariogenic effect as well as efficient polymerization. Further studies using various materials and experimental conditions are being encouraged.

• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.100-105
• /
• 1994

We have reduced the oscillating linewidth of the commercial single mode InGaAsP visible laser diodes which emits in the 657 nm region of the spectrum down to 10 MHz by making a extended cavity employing the Littrow-type grating. The wavelength tuning characteristics of the commercial visible laser diode (CQL820D, Philips Co.) for the grating angle, laser temperature, and injection currents were measured by using the wavemeter. The proportional coefficients of the laser were found to be 1 THzlmrad, 32.4 GHz/K, and 6.14 GHz/mA, respectively.tively.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.25 no.1
• /
• pp.62-75
• /
• 1998

The main purpose of this study was to compare the anticariogenecity of glass ionomer restorative material polymerized by argon laser versus visible light, The results from the present study can be summarized as follows; 1. Under the polarized light microscope, the specimens of laser-cured group showed the shallower lesion body than that of visible-light cured group, both in the stage of lesion initiation and progression. 2. Glass ionomer material cured by visible light showed shallower body of lesion than that of composite resin cured by argon laser at the stage of lesion progression(p<0.05). It was suggested fluoride released from the glass ionomer might have the additive anticariogenic effect. 3. Statistical difference between groups on depth of lesion body was evident after lesion progression (p<0.05). It was suggested that anticariogenic effect by argon laser was more effective at the stage of lesion progression than the lesion initiation. 4. The increment of lesion body during progression was highest in group IV (p<0.05). 5. Based upon the above-mentioned results of this study, it can be concluded that the advantage of anticariogenic effect and short curing time of argon laser in glass ionomer polymerization should be considered in children and adolescents whose caries activity is relatively higher.