• Journal of Sensor Science and Technology
• /
• v.29 no.2
• /
• pp.75-81
• /
• 2020

We introduce a new visible light communication (VLC) method in which three-level return-to-zero (RZ) modulation is used for flicker-free transmission. In the VLC transmitter, the three-level RZ modulation ensures that the average optical power is constant; thus, a flicker-free light-emitting diode (LED) light is achieved. In the VLC receiver, a resistor-capacitor high-pass filter is used for generating spike signals, which are used for data recovery while eliminating the 120 Hz optical noise from adjacent lighting lamps. In transmission experiments, we applied this method for wireless transmission of an air quality sensor message using the visible light of an LED array. This configuration is useful for the construction of indoor wireless sensor networks for air pollution monitoring using LED lights.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.8
• /
• pp.905-910
• /
• 2010

In this paper, visible light communication(VLC) system modulated by a switching driver circuit of lighting light emitting diode(LED), not only for illumination but also for optical wireless communication, is implemented. Presented system could overcome the drawbacks of prior linear modulation technique such as low efficiency, heat generation, and limits to realization of high power lighting LED. Experimental results from the realized digital audio system are presented to confirm the superiority of the proposed circuit. Our prototype achieves a transmission data rate of 10 Mbps with a radius of 1.5 meters using 20 W output power, and the signals were detected successfully.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.241-241
• /
• 2010

Recently high and persistent spontaneous buildup of a surface potential (SP) upon vacuum deposition of tris (8-hydroxyquinolinato) aluminum (III) ($Alq_3$), which is widely used for organic light emitting devices. The removal of the giant surface potential by visible light irradiation has also been reported. In this study, we coated $Alq_3$ on the FTO substrate and raise the capacity for absorbing sun light. The $Alq_3$ which is green light emitting diode emits light at wavelengths between 500 and 550nm. If we apply one's FTO/$Alq_3$ substrate in one's DSSC, we could get higher energy conversion efficiency because the N719 dye that we used for fabricating the DSSC emits light just at near 540nm. The energy conversion efficiency of approximately 4.8 % at the condition of irradiation of AM 1.5 (100 mW/$cm^2$) simulated sunlight, and the $J_{sc}$ is 12.0 mA/$cm^2$, $V_{oc}$ is 0.71 V, FF is 0.56, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.4A
• /
• pp.219-226
• /
• 2012

We investigated the performance of a visible light communication (VLC) transceiver applicable to both of illumination and wireless communication. we considered the visibility of VLC, the easy connection for wireless communication and high-speed transmission and implemented VLC transceiver based on edge-emitting laser diode and silicon photodiode. The proposed VLC transceiver is designated to operate in a full duplex mode at high speed of 120 Mbit/s. The shielding method that is employed as a means to reduce the light cross coupling effect inside the VLC transceiver is proposed and its performance is experimentally measured. We also applied optical antenna to have the larger angle of field of view (FOV) to novel structure of VLC transceiver and examined and analyzed their bit error rate performance, photometric result with respect to the transmission distance, the coverage range and the tilt degree as transmission link characteristic between two transceivers without optical antenna and with optical antenna.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.226-229
• /
• 2010

LED(Light Emitting Diode) is an emitting device which energy is same to the bandgap of p-type and n-type semiconductor junction. Recently high brightness LED is used in fish-luring light and traffic signal light alternative of normal light bulb, and widely used in the area of display pannel. Moreover nowadays LED has been used as a back light of LCD display. Recently, visible light communication(VLC) using LED, that allow two-way serial data communication between LEDs over a distance of sveral centimeters or meters, has been widely studied in the area of digital information transmission along with illumination and display. In this paper, we present LED communication system and their applications.

• International journal of advanced smart convergence
• /
• v.1 no.1
• /
• pp.52-56
• /
• 2012

As inexhaustible clean energy, solar energy will be the most ideal green energy in the 21st century. The effective method to convert solar energy into electrical energy is by solar photovoltaic power generation technologies. LED Emitting Diode is a kind of component which can transform electricity into visible light. As the smart current control system for photovoltaic street lights, the proposed system has improved the battery charging and discharging mechanism to extend the lifespan and effectively controls the LED discharge current according to battery charge state and lighting.

• ETRI Journal
• /
• v.18 no.3
• /
• pp.181-193
• /
• 1996

A blue light emitting device has been successfully fabricated using a polymer with regulated conjugation length containing trimethylsilyl substituted phenylenevinylene units. Electroluminescence from the device has an emission maximum at 470 nm. The device shows typical diode characteristics with operating voltage of 20 V and the light becomes visible at a current density of less than $0.5;mA/cm^2$. The electroluminescence spectrum is virtually identical with the photoluminescence spectrum, indicating that the radiation mechanisms are the same for both. A light emitting device using the blend of a large band gap polymer and a small band gap polymer was also fabricated. Light emission from the small band gap polymer shows much improved quantum efficiency, but there is no light emission from the large band gap polymer. Quantum efficiency of the blend increases up to about two orders of magnitude greater than that of the small band gap polymer with increasing proportion of the large band gap polymer. The improvement in quantum efficiency is interpreted in terms of exciton transfer and the hole blocking behaviour of the large band gap polymer. Finally, we have fabricated a patterned flexible light emitting device using the high quantum efficiency polymer blend system.

• Information and Communications Magazine
• /
• v.28 no.12
• /
• pp.50-60
• /
• 2011

Visible light communication(VLC) is one type of short-range, optical, and wireless communication system utilizing light emitting diode(LED) and laser diode(LD) as optical source. In a VLC system, visible light is used as a transmission medium and used to illuminate. Using VLC has a lot of advantages: it is harmless to human body; it transmits with high power, and it has excellent security, a high data rate, and a license free frequency band. With such a unique blend of communication and illumination in one system, the most common application would be an indoor environment. We aim at reviewing key issues in VLC network such as : FOV(field of view), priority MAC, cooperative MAC, link switching, LED-ID technique, cell site diversity, and link recovery.

• Journal of Sensor Science and Technology
• /
• v.30 no.4
• /
• pp.196-203
• /
• 2021

In this study, an optical identification system was developed, wherein visible light is used to transmit the interrogating signal, and infrared is used to send the response signal. In the reader, visible light from a light emitting diode (LED) array was modulated via modified pulse width modulation for flicker-free illumination and dimming control. Moreover, the duty factor of the dimming control time was employed to control the illumination from the LED. In the transponder, the spike signal in the output of the high-pass filter was utilized to recover the interrogating signal while preventing interference from the 120-Hz noise from adjacent lighting lamps. The illumination was controlled in 26-86% range of the constant wave LED illumination by changing the duty factor from 20% to 90%. This configuration is advantageous for the construction of optical identification systems for automatic security check and car fare calculation at toll gates or parking facilities.

• Journal of Sensor Science and Technology
• /
• v.29 no.3
• /
• pp.149-155
• /
• 2020

In this study, we employed Manchester code for illumination control and flicker prevention of the light-emitting diode (LED) used in a visible light communication (VLC) system. In the VLC transmitter, the duty factor of the Manchester code was utilized for illumination control; in the VLC receiver, the spike signal from an RC-high pass filter was utilized to recover the transmitted signal whilst suppressing the 120-Hz noise arising from adjacent lighting lamps. Instead of the clock being transmitted in a separate channel, a syncmark signal was transmitted in front of each data byte and used as the reference time for transforming the Manchester code to non-return-to-zero (NRZ) data in the receiver. In experiments, the LED illumination was controlled in the range of approximately 12-84% of the constant wave (CW) light via changing of the duty factor from 10% to 90%. This scheme is useful for constructing indoor wireless sensor networks using LED light that is flicker-free and presents capability for illumination control.