• Journal of Pharmaceutical Investigation
• /
• v.35 no.6
• /
• pp.417-422
• /
• 2005

This study was aimed to design and formulate the moisture-activated patches containing ofloxacin and lidocaine for antibacterial and local anesthetic action. The solubility of lidocaine at $32^{\circ}C$ in various vehicles decreased in the rank order of PG $759.5{\pm}44.5\;mg/mL$ > PGL > IPM > PEG 300 > PEG 400 > Ethanol > PGMC > DGME > PGML > OA > $Captex^{\circledR}\;300$ > $Captex^{\circledR}\;200$ > water $(4.0{\pm}0.1\;mg/mL)$. Ofloxacin revealed very low solubility, which the highest solubility was obtained from PEG 400 $(18.7{\pm}6.3\;mg/mL)$ among the vehicles used. The addition of lactic acid increased the solubility of ofloxacin dramatically; the solubility at 5% lactic acid was $133.7{\pm}9.7\;mg/mL$. As $2-hydroxypropyl-{\beta}-cyclodextrin$ was added at the concentrations of 40, 80, 120, 160 and 200 mM, the solubilities of lidocaine and ofloxacin were enhanced up to three and two times, respectively, with concentration-dependent pattern. Gel intermediates for filmtype patches were prepared with mucoadhesive polymer, viscosity builders, lidocaine or ofloxacin at pH values from 5 to 7. Gels were cast onto a release liner and dried at room temperature. Dried patch was attached onto an adhesive backing layer, thus forming a patch system. Patches containing a single drug component were characterized by in vitro measurement of drug release rates through a cellulose barrier membrane. The release study was carried out at $37^{\circ}C$ using a Franz-type cell. Receptor solutions were isotonic phosphate buffers (pH 7.4). Samples $(100\;{\mu}L)$ were taken over 24 hours and quantitated by a verified HPLC method. The releases from all tested were proportional to the square root of time. The release rates were 0.9, 157.3 and $281.7\;{\mu}g/cm^{2}/min^{1/2}$ for the lidocaine patches and 19.8,37.2 and $50.7\;{\mu}g/cm^{2}/min^{1/2}$ for the ofloxacin patches at the concentrations of 0.3, 0.5 and 1 %, respectively. The release rates were dose dependent in both drug patches $(R^{2}\;=\;0.9077\;for\;lidocaine;\;R^{2}\;=\;0.9949\;for\;ofloxacin)$ and those were also thickness-dependent $(R^{2}\;=\;0.9246\;for\;lidocaine;\;R^{2}\;=\;0.9512\;for\;ofloxacin)$.

• Journal of Conservation Science
• /
• v.35 no.5
• /
• pp.480-493
• /
• 2019

In this study, the method for processing glue and glue-alum sizing from the dancheong ground treatment was evaluated with respect to weather resistance, and its effect on the conservation of dancheong was analyzed. Viscosity and pH of the glue and glue-alum specimen were measured and classified into three categories(none layer, glue layer, and glue-alum layer), which were further classified according to low concentration(four times for 2%) and high concentration(once for 10%). The base layer formation was subsequently classified into three categories based on pigment adoption, namely, Noerok(celadonite), Seokganju(terra rossa), and Jangdan(red lead). The completed specimen was subjected to a changing-environment experiment for evaluating weather resistance and observing the surface. Color variations were analyzed before and after the experiment. The results indicate that glue-alum sizing comprising 5% alum or 7% alum has strong acidity that can affect the life of dancheong, and the high level of 7% alum makes it difficult to create a solid coating layer. After ultraviolet irradiation, the specimen with 7% alum changes its color to yellow. Furthermore, after moisture absorption and drying, cracks can be observed on the entire specimen surface that corroborate the physical change. Additionally, gas-based corrosion causes marginal surface changes. Hence, the formation of a stable coating layer can be achieved by incorporating a low concentration glue solution that is almost neutral, and the application of glue-alum sizing having 2% concentration can aid in the conservation of dancheong.

• The Korean Journal of Pharmacology
• /
• v.24 no.1
• /
• pp.43-52
• /
• 1988

To elucidate the mechanism of action of local anesthetics, the effects of local anethetics on the microenvironment of the lipid bilayers of synaptosomal plasma membrane vesicles (SPMV) isolated from bovine brain and dimyristoylphosphatidylcholine (DMPC) multilamellar liposomes were investigated employing the intermolecular excimer fluorescence technique and differential scanning calorimetry (DSC). The relative intensities of excimer and monomer fluorescence of pyrene are a simple linear function of the viscosity of a homologous series of solvents. The microviscosity(${\eta}$)of the hydrocarbon region of SPMV was measured by this method and the value was $57.3{\pm}5.3\;cP$ at $37^{\circ}C$. In the presence of lidocaine-HCl and procaine-HCl, the values decreased to $46.5{\pm}5.1\;cP$ and $54.7{\pm}4.8\;cP$, respectvely. The differential scanning thermograms of DMPC multilamellar liposomes showed that local anesthetics significantly lowered the phase transition temperature, broadened the thermogram peaks, and reduced the size of the cooperative unit. These results indicate that local anesthetics have significant fluidizing effects on biomembranes and perturbation of membrane lipids may produce some, but not all, of their pharmacological actions.

• Korean Chemical Engineering Research
• /
• v.47 no.4
• /
• pp.481-487
• /
• 2009

In this of study, effects of input air velocity(0.05~0.22 m/sec) and molten carbonate salt temperature ($870{\sim}970^{\circ}C$) on flow regime transition have been studied by adopting a drift-flux model of air holdup and a stochastic analysis of differential pressure fluctuations in an air-molten sodium carbonate salt two-phase system(molten salt oxidation process). Air holdup where the flow regime transition begins was determined by air holdup-drift flux plot. The air holdup value which the flow regime transition begins was increased with increasing molten carbonate salt temperature due to the decrease of viscosity and surface tension of molten carbonate salt. To characterize the flow regime transition more quantitatively, differential pressure fluctuation signals have been analyzed by adopting the stochastic method such as phase space portraits and Kolmogorov entropy, The Kolmogorov entropy decreased with an increasing of molten carbonate salt temperature but increased gradually with an increase in an air velocity, however, it exhibited different tendency with the flow regime and the air velocity value which flow regime transition begins was same to the results of drift-flux analysis.

• Applied Chemistry for Engineering
• /
• v.31 no.3
• /
• pp.267-276
• /
• 2020

Poly(epichlorohydrin) copolyol series (PECH copolyols) were synthesized via cationic ring-opening copolymerization (ROCP) of oxirane-based monomers and effects of reaction temperature, solvent type, and initiator were studied. As a comonomer, two types of alkylene oxides were used, and polymerization conditions were conducted both with diethylene glycol (DEG) as an initiator in methylene chloride (MC) solvent and tripropylene glycol (TPG) in toluene solvent. In order to induce the active monomer (AM) mechanism in the ring-opening copolymerization reaction, the monomer was injected by an incremental monomer addition (IMA) method using a syringe pump, and the polymerization was performed at -5 ℃. PECH copolyol, a synthesized ephichorohydrin (ECH)-based copolyol, was converted to glycidyl azide-based energy-containing copolyol (GAP copolyol) by azadizing the ECH unit through a substitution reaction. It was confirmed that the synthesized azide copolyol had little effects on changes of the solvent and the initiator. Also, the molecular weight increased 500 after the azide reaction, thereby the GAP copolyol was polymerized as designed. As the content of the comonomer increased, both the T_g and viscosity tended to decrease due to the influence of the alkyl chain length. It is possible to fundamentally prevent CH₃N₃ amount produced in the azide reaction process, and it is expected that a large-scale process could be achievable.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.199-209
• /
• 1994

$PbTiO_3$ thin films were prepared on soda-lime-silica slide glasses, Si-wafer and sapphire substrate by the dip-coating of precursor solution. As starting materials, titanium tetra iso-propoxide and lead acetate trihydrate were used. Then acetylacetone was added to prepare stable sol. The effect of the parameters such as viscosity and composition of sol were investigated. The optical transmittance at visible range, refractive index, IR spectra were measured in varying compositions, thickness and heat treatment temperature. The crystallization of $PbTiO_3$ films were measured by using XRD and SEM. Diffusion of compositions from slide glass to thin film were investigated by using EDX, too. These sols not precipitated for 20 days. Transmittance of $PbTiO_3$ films at visible range were decreased with the increase of thickness and heat treatment temperatures, and were exhibited flat spectra. Pyrochlore type appeared in the films on slide glass and perovskite type appeared in the films on Si-wafer or sapphire at $600^{\circ}C$. Perovskite crystals transformed to $PbTi_3O_7$ phase at $800^{\circ}C$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.1
• /
• pp.47-53
• /
• 2011

The artificial aggregates (AAs) were manufactured from the parent batch powders consisting of bottom ash containing excess unburned carbon and dredged soil, 7 : 3 weight ratio by direct sintering method and those physical properties were evaluated. Especially, the effects of waste glass or frit (NWG) which was made by addition of 5 wt% $Na_2O$ to the waste glass upon the bloating phenomenon of AAs were analyzed. The AAs manufactured from the parent batch powders showed a lower specific gravity than that of specimens containing waste glass or NWG due to excess u$Na_2O$nburned carbon which usually obstructs a sintering process. But, the waste glass added on parent batch powders promoted the sintering and densification thus increased the specific gravity of AAs. Also the specific gravity of AAs added with 5 wt% NWG, was lowered compared to that of AAs added with as-received waste glass. This is because of bloating of shell which captures gases owing to the lowered viscosity of liquid formed at the specimen surface caused by $Na_2O$ addition. In conclusion, the AAs sintered at above $1100^{\circ}C$ in this study showed characters of lightweight aggregate of specific gravity 1.15~1.34 and water absorption 11~19 %, and the bloating phenomenon of AAs was occurred at the shell rather black core part.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.132-139
• /
• 2005

Sintering behavior of $BaO-Nd_{2}O_3-TiO_2$ with a Pb-based glassceramics frit were investigated in order to understand an effect of glassceramics as a low temperature sintering agent on dielectric ceramics. A green sheet form was fabricated through tape casting method with the glassceramic fut added $BaO-Nd_{2}O_3-TiO_2$. The dispersion properties, rheological properties and final density of dielectric composit slurry as a function of amount and composition of organic additives was examined. The dispersants' addition was effective in controlling dispersion of the ceramics in solution. The addition of excessive dispersant showed adverse effect on dispersion. The prepared slurries, containing ceramic : powders, glass-ceramics and various kinds of organic viechles, exhibited typical shear thinning behavior. The best properties of tape casting appeared powder to solvent ratio 65 : 35 and amount of the binder 6 wt$\%$ and plasticizer 3 wt$\%$. The viscosity of the slurry was 677 cps and green/sintered density in the tape was $3.3 g/cm^3,\;5.56 g/cm^3$ respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.2
• /
• pp.320-328
• /
• 2014

Biodiesel has very similar physical properties (density, kinematic viscosity) and has even higher cetane number compare with conventional diesel. There are no necessity to change or modify the infra-structure & engine system. It is known that fatty acid methyl ester (FAME) is oxygen-contained components increasing the combustibility, biodegradability and reduced the exhaust harmful gas. These things made the biodiesel more popular as an alternative diesel fuel. But biodiesel's sources are controversial issues about $CO_2$ reduction effect at this time because those mainly come from edible plants such as soy, palm, rapeseed already spent lot of $CO_2$ to cultivate. Whereas micro-algae is focused because they are inedible and has rapid growth rates & high carbon-dioxide adsorption rate per area. In this study, we analyze the each FAME components using $GC{\times}GC$-TOFMS in stead of GC-FID and verify the previous total FAME contents method's applicability through the micro algal biodiesel derived from Dunaliella tertiolecta.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.513-518
• /
• 2019

Friction Stir Welding is a welding technique for metal materials that utilizes the heat generated by friction between the material to be welded and the welding tool that rotates at high speed. In this study, a numerical analysis method was used to analyze the change in the internal temperature of the welded material during friction stir welding. As the welding target material, AZ31 magnesium alloy was applied and the welding phenomenon was considered a flow characteristic, in which a melting-pool was formed. FLUENT was used as the numerical tool to perform the flow analysis. For flow analysis of the welding process, the welding material was assumed to be a high viscosity Newtonian fluid, and the boundary condition of the welding tool and the material was considered to be the condition that friction and slippage occur simultaneously. Analyses were carried out for various rotational speeds and the translational moving speed of the welding tool as variables. The analysis results showed that the higher the rotational speed of the welding tool and the slower the welding tool movement speed, the higher the maximum temperature in the material increases. Moreover, the difference in the rotational speed of the welding tool has a greater effect on the temperature change.