• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.784-787
• /
• 2004

Modified version of subspace iteration method using accelerated starting vectors is proposed to efficiently calculate free vibration modes of structures. Proposed method employs accelerated Lanczos starting vectors that can reduce the number of iterations in the subspace iteration method. Proposed method is more efficient than the conventional method when the number of required modes is relatively small. To verify the efficiency of proposed method, two numerical examples are presented.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.973-978
• /
• 2001

Noise reduction has become a major issue of the manufacturing industry. This paper describes the reduction of noise and vibration of rotary compressors. Empirical design for the present strap of the accumulator has been considered to be sufficient for the constraint of the accumulator resonance modes without thorough study. Recently, however, some researchers found out that the accumulator contributes considerably to the sound propagation. In this paper, the contribution of accumulator to the noise propagation is investigated through sound measuring experiments by checking the directivity of the noise. And, experimental modal analysis results show that frequencies of some resonance modes of the accumulator coincide with the highest peaks on sound spectrum. To demonstrate the reason for those resonance modes, a finite element analysis is conducted. Normal mode analysis of the finite element model of the rotary compressor shows the mechanism of the accumulator resonance modes.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.4
• /
• pp.372-376
• /
• 2012

The most common type of the piezoelectric energy harvester is the cantilevered beam since it is attached to the host structure and tuned to the frequency of the base excitation easily. However, the excessive strain at the fixed end of cantilevered beam causes some problems such as fatigue and durability. The use of higher vibration modes of the cantilevered beam may reduce the concentration of the strain at the fixed end since the strains of higher modes are distributed along the span. The results show that the use of high vibration mode is not efficient for power generation, but it reduces the excessive strain lever at typical region to prevent the failure by fatigue.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.178-185
• /
• 2001

This paper describes the correlation between the interior noise and the trunk wall vibration. Using the vibro-acoustic reciprocity, effect of the trunk wall vibration on the compartment noise is investigated on a medium size car. In the low frequency range, vehicle interior noise is dominated by several acoustic modes of the passenger compartment and the vibration modes of the surrounding shell parts. Especially, vibration of the trunk wall radiates sound and it is transferred through holes on the package tray into the passenger compartment. This paper experimentally reveals that sound can be well produced at some particular vibration modes of the trunk lid and it strongly influences the compartment noise through package tray holes. Contributions of the trunk walls to the interior noise are estimated by measuring the acoustic-structural transfer function, based on the vibro-acoustical reciprocity theorem.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.619-624
• /
• 2000

Longitudinal vibration of an axially moving material is investigated by using the assumed modes method. to circumvent a difficulty in choosing the comparison functions which satisfy the boundary conditions the assumed modes method is adopted by which equations of motion are discretized. Based on the discretized equations, the complex eigenvalue problem is solved and then the effects of the translating velocity on the natural frequencies and modes are analyzed.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.45-50
• /
• 2020

Magnetoelectric (ME) composites were designed using the PMN-PZT single crystal and Ni foils; the properties and magnetic-field sensitivities of ME composites with different piezoelectric vibration modes (i.e., 31, 32, and 36 modes that depend on the crystal orientation of the single crystal) were compared. In the off-resonance condition, the ME coupling properties of the ME composites with the 32 and 36 piezoelectric vibration modes were better than those of the ME composites with the 31 piezoelectric vibration mode. However, in the resonance condition, the ME coupling properties of the ME composites were almost similar, irrespective of the piezoelectric vibration mode. Additionally, in the off-resonance condition (at 1 kHz), the magnetic-field sensitivity of the ME composites with the 36 piezoelectric vibration mode was up to 2 nT and those of the ME composites with the 31 and 32 piezoelectric vibration modes were up to 5 nT. These magnetic-field sensitivities are similar to those offered by conventional high-sensitivity magnetic-field sensors; the potential of the proposed sensor to replace costly and bulky high-sensitivity magnetic field sensors is significant.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.484-487
• /
• 2006

In this paper, linear ultrasonic actuators are designed using two dimensional motions of a PMW-PT piezoelectric plate. By equalizing the natural frequencies of longitudinal and transverse vibration modes in the cantilever structure, the ultrasonic motion of the combined vibration modes are generated. We have designed two different PMN-PT actuators: one uses a tip attached on the edge of the actuator and it drives the object in the perpendicular direction of the tip. In other model, the actuator plate moves itself through stationary guides. Prototypes of the two models are manufactured and experiments results are compared to the theoretical and numerical results. The effects of structural characteristics and the friction force existing between the actuator tip and the moving object are considered. Experiments show the possibility of small size ultrasonic linear motors which can be applicable to small form factor information storage and phone camera actuators.

• Journal of KSNVE
• /
• v.9 no.3
• /
• pp.509-516
• /
• 1999

The ESPI (Electronic Speckle Pattern Interferometry) algorithm has been simulated to calculate vibrational modes of a thin right-angled STS304 plate. The phase transformation of the reference wave of the ESPI is carried out only one time during vibration in order to clarify ESPI speckle patterns. Two dimensional vibrational modes are calculated from one ESPI pattern before vibration onset and two ESPI patterns during vibrations but with and without the phase transformation. The ESPI harmonic results are compared with those derived from the finite element method (FEM), and they agree very well. Additionally a phase unwrapping algorithm has been newly developed to derive a displacement map from an ESPI phase map.

• Advances in Computational Design
• /
• v.1 no.2
• /
• pp.155-173
• /
• 2016

This paper presents a method of design for the energy harvesting of a piezoelectric cantilever beam. Vibration modes have strain nodes where the strain distribution changes in the direction of the beam length. Covering the strain nodes of the vibration modes with continuous electrodes effects a cancellation of the voltages outputs. The use of segmented electrodes avoids cancellations of the voltage for multi-mode vibration. The resistive load affects the voltage and generated power. The optimum resistive load is considered for segmented and continuous electrodes, and then the power output is verified. One of the effective parameters on energy harvesting performance is the existence of concentrated mass. This topic is studied in this paper. Resonance and off-resonance cases are considered for the harvester. In this paper, both theoretical and experimental methods are used for satisfactory results.

• Journal of Institute of Convergence Technology
• /
• v.1 no.1
• /
• pp.18-23
• /
• 2011

Shaping an input command through considering the resonant modes of multi degrees of freedom system, it is possible to realize the wanted motion, without exciting the uncontrollable modes of the flexible system. But, an increase of modes to be considered brings inevitably about the time delay due to an excessive rising time. On the purpose of reducing the rising time, only the interesting and dominant modes can be considered to determine the timing pulses of input shaper. In this paper, an effect of shaper by the partial modes is analysed for a specific system and the input shapers by the partial modes are analysed for three d.o.f damped system, using Matlab simulation.