• 한국전산구조공학회논문집
• /
• 제25권1호
• /
• pp.81-89
• /
• 2012

본 연구에서는 무선 가속도 센서노드를 이용한 강 거더 볼트연결 부재의 진동기반 손상 모니터링 체계를 제안하였다. 이 같은 연구목표를 위해, 다음과 같은 연구를 수행하였다. 먼저, 무선 가속도 센서노드의 하드웨어 구성 및 내장된 작동 소프트웨어를 제시하였다. 다음으로, 강 거더 볼트연결 부재의 진동기반 손상 모니터링 체계를 제시하였다. 손상 모니터링 체계는 가속도 응답특성 분석을 통해 전역적 손상발생 경보 및 손상위치 추정을 수행한다. 전역적 손상발생 경보는 파워스펙트럼밀도의 상관계수를 적용하였다. 손상위치 추정은 고유 진동수기반 손상검색 기법과 모드형상기반 손상검색 기법을 적용하였다. 마지막으로, 모형 강 거더의 볼트연결 부재 손상을 식별하기 위한 진동기반 손상 모니터링 체계의 적용성을 검증하였다.

• 한국소음진동공학회논문집
• /
• 제26권5호
• /
• pp.609-615
• /
• 2016

Measuring similarity between two signals is a key element of the location template matching (LTM) method which is one of impact source localization technique. As a measure of similarity, the correlation coefficient is most widely used, and the group delay based method is recently proposed to improve the accuracy of finding the impact source. In practice, the LTM method assumes that the similarity between two signals decreases as the distance between two corresponding impact points increases, where the distance between two neighboring impact points defines the grid spacing. In this paper, it is shown that this assumption is not always true but the correlation coefficients fluctuate forming a main robe and many side robes as the distance between two neighboring impact points increases. On the other hand, the standard deviation of group delay sharply increases with a small increase of the grid spacing. These are demonstrated by using a simple cantilever beam. Based on these findings, an optimal way of implementing the LTM method may be suggested by combining the correlation coefficient and the group delay based approaches.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.172-176
• /
• 2000

A series of preliminary experiments were carried out to quantify the annoyance are noisiness caused by floor impact noise. From the results of the experiments. the heavy impact source was found to be felt louder and noisier than the light impact source. Measurements of noise were also conducted by a diagnostic system based on the model(the model consists of the autocorrelators and the cross-correlation for signals arriving at two ear entrants) of the human auditory-brain system. Physical factors in the model were calculated by use of the ACF(autocorrelation function) and IACF(interaural cross correlation function) of binaural signals. From the ACF/IACF analysis, it was found that perceived loudness of floor impact noise could be represented by the factors of the ACF/IACF model.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.960-963
• /
• 2003

Sound intensity method is well known as a visualization technique of sound field and sound propagation in noise control. Sound intensity is a vector quantity that describes the magnitude and the direction of net flow of acoustic energy at a given position. The current measuring method is expensive and difficult to identify the noise source exactly. In this paper, we have studied the noise source identification and the characteristics of noise source of rotary compressor for air conditioner using complex sound intensity method. The new method for instantaneous sound intensity is also proposed and it is useful for transient state and steady state. The criteria of these state, select auto correlation coefficient. The advantage, simplicity and economic attribution of this method are verified by analyzing the characteristics of noise source with instantaneous sound intensity compared to mean sound intensity.

• Wind and Structures
• /
• 제13권3호
• /
• pp.257-273
• /
• 2010

The aerodynamic and aero-elastic model tests of the China''s highest cooling tower has been carried out in the TJ-3 Boundary Layer Wind Tunnel of Tongji University. By adopting a scanivalve system, the external wind pressure is firstly measured on $12{\times}36$ taps for a single tower, two and four grouped towers under the condition of both smooth flow and the boundary layer due to surrounding geographic and building topography. The measurements of internal wind pressure distribution of $6{\times}36$ taps are taken for a single tower under the various ventilation ratios ranging from 0% to 100% of stuffing layers located at the bottom of the tower. In the last stage, the wind tunnel tests with an aero-elastic model are carefully conducted to determine wind-induced displacements at six levels (each with eight points) with laser displacement sensors. According to the measurement results of wind pressure or vibration response, the extreme aerodynamic loading values of the single or grouped towers are accordingly analyzed based on probability correlation technique.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.647-653
• /
• 2009

Taguchi parameter design is an approach to reducing performance variation of quality characteristic value in products and processes. Taguchi has used SN (Signal to Noise) ratio to achieve the appropriate set of operating conditions where variability around target is low in the Taguchi parameter design. This paper describes the prediction technique of vehicle performance using parameter analysis to reduce man hour and test development period as well as to achieve stable NVH performance. Design engineer could efficiently decide the design variable using parameter analysis database in early design stage. These improvements can reduce the time needed to develop better vehicles.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.903-912
• /
• 2007

One of the crucial factors which determine the quality and the accuracy of SEA model is how subsystems are defined. Experimental SEA technique had been a unique way to divide entire systems accurately for mid-frequency range, until FEA based virtual FRF response technique, virtual SEA method presented. Virtaul SEA has been developed for predictive SEA tool in early design process. In this study, Modal analysis results from modified crash FE model is used for Statistical transfer matrix. Observation nodes on the cockpit are grouped by attractive substructuring method based on point to point transfer and correlation matrix. Complex cockpit structure is divided into subsystems by automatic substructuring. Comparison with experimental SEA results validates the application of Virtual SEA to cockpit.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.594-601
• /
• 1997

Propeller fans are commonly equipped in outdoor units of air-conditioners to provide effective cooling in a dried heat exchanger. A new design technique was developed to satisfy requirements of aerodynamic and aeroacoustic performance, which employs the intersection method of two cylinders for mean camber line. Three proto-types of propeller fan including Palm-Shaped, Highly-Swept(PSHS) fan (proto 3)were not only to provide low lift forces for dipole sound, but also to reduce the organized tip vortices interacting with the fan guide causing narrow-banded rotating instabilities. Cross-correlation technique was applied to study flow noise source characteristics for three proto-type fans designed. The cross-correlations between a microphone at far field and a hot-wire sensor at near field show that flows near hub region of proto 3 fan are less organized and the flow structures especially at high flow rate coefficients for proto 3 fan are less correlated with noise generated than other proto-types fans.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권1호
• /
• pp.128-141
• /
• 2015

Independent Component Analysis (ICA), one of the blind source separation methods, can be applied for extracting unknown source signals only from received signals. This is accomplished by finding statistical independence of signal mixtures and has been successfully applied to myriad fields such as medical science, image processing, and numerous others. Nevertheless, there are inherent problems that have been reported when using this technique: instability and invalid ordering of separated signals, particularly when using a conventional ICA technique in vibratory source signal identification of complex structures. In this study, a simple iterative algorithm of the conventional ICA has been proposed to mitigate these problems. The proposed method to extract more stable source signals having valid order includes an iterative and reordering process of extracted mixing matrix to reconstruct finally converged source signals, referring to the magnitudes of correlation coefficients between the intermediately separated signals and the signals measured on or nearby sources. In order to review the problems of the conventional ICA technique and to validate the proposed method, numerical analyses have been carried out for a virtual response model and a 30 m class submarine model. Moreover, in order to investigate applicability of the proposed method to real problem of complex structure, an experiment has been carried out for a scaled submarine mockup. The results show that the proposed method could resolve the inherent problems of a conventional ICA technique.

• Earthquakes and Structures
• /
• 제3권1호
• /
• pp.17-35
• /
• 2012

Simplified equations for fundamental period of vibration of skeletal structures provided by most seismic design provisions suffer from the absence of any associated confidence levels and of any reference to their empirical basis. Therefore, such equations may typically give a sector of designers the false impression of yielding a fairly accurate value of the period of vibration. This paper, although not addressing simplified codes equations, introduces a set of mathematical equations utilizing the theory of error propagation and First-Order Second-Moment (FOSM) techniques to determine bounds on the relative error in theoretically calculated fundamental period of vibration of skeletal structures. In a complementary step, and for verification purposes, Monte Carlo simulation technique has been also applied. The latter, despite involving larger computational effort, is expected to provide more precise estimates than FOSM methods. Studies of parametric uncertainties applied to reinforced concrete frame bents - potentially idealized as SDOF systems - are conducted demonstrating the effect of randomness and uncertainty of various relevant properties, shaping both mass and stiffness, on the variance (i.e. relative error) in the estimated period of vibration. Correlation between mass and stiffness parameters - regarded as random variables - is also thoroughly discussed. According to achieved results, a relative error in the period of vibration in the order of 19% for new designs/constructions and of about 25% for existing structures for assessment purposes - and even climbing up to about 36% in some special applications and/or circumstances - is acknowledged when adopting estimates gathered from the literature for relative errors in the relevant random input variables.