• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.105-106
• /
• 2008

Structural, optical and electrical properties of CdS films deposited by chemical bath deposition (CBD), which are a very attractive method for low-cost and large-area solar cells, are presented. Cadmium sulfide (CdS) is II-VI semiconductor with a wide band gap of approximately 2.42 eV. CdS films have a great application potential such as solar cell, optical detector and optoelectronics device. In this paper, effects of Rapid Thermal Process (RTP) on the properties of CdS films were investigated. The CdS films were prepared on a glass by chemical bath deposition (CBD) and subsequently annealed at standard temperature $(400^{\circ}C)$ and treatment time (10 min) in various atmospheres (air, vacuum and $N_2$). The CdS films treated RTP in $N_2$ for to min were showed larger grain size and higher carrier density than the other samples.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.905-909
• /
• 2001

The significance of casting/forging process for reducing the production cost of large components is being noted in these days. This casting/forging process is a method of forging a workpiece preformed by casting into the final shape. In this study, the casting/forging process has been applied in manufacturing a large aluminum flange in order to determine the optimum forging condition of the aluminum flange. The optimum range of forging temperature of Al 5083 was from $420^{\circ}C$ to $450^{\circ}C$. The suitable strain rate was 1.5 $sec^{-1}$. The deformation amount of a preform in a forging process is key role in the mechanical properties of casting/forging products. In order to find the change of mechanical properties according to effective stain of cast aluminum billets, a hot upsetting test were performed with rectangular blocks and then a uniaxial tensile test was performed with specimens cut from the upsetted billets. The tensile strength and the elongation of cast/upsetted aluminum billets were increased largely until the effective strain was 0.7. FE analysis was performed to determine the configurations of cast preform and die for an aluminum flange. In the FE analysis, the forging load-limit was fixed 1500ton for the low equipment cost. The cast preform was designed so that the effective stain around the neck of a flange exceeds 0.7. In the forging experiment for an aluminum flange, it was confirmed that the optimal configuration of the cast preform predicted by FE analysis was very useful. The cast/forged products using designed preform were made perfectly without any defects.

• 대한기계학회논문집B
• /
• 제25권6호
• /
• pp.799-803
• /
• 2001

Miniature heat pipe(MHP) with woven-wired wick was used to cool the CPU of a notebook PC. The pipe with circular cross-section was pressed and bent for packaging the MHP into a notebook PC with very limited compact packaging space. A cross-sectional area of the pipe is reduced about 30% as the MHP with 4mm diameter is pressed to 2mm thickness. In the present study a performance test has been performed in order to review varying of operating performance according to pressed thickness variation and heat dissipation capacity of MHP cooling module that is packaged on a notebook PC. New wick type was considered for overcoming low heat transfer limit when MHP is pressed to thin-plate. The limiting thickness or pressing is shown to be within the range of 2mm∼2.5mm through the performance test with varying the pressing thickness. When the wall thickness of 0.4mm is reduced to 0.25mm for minimizing conductive thermal resistance through the wall of heat pipe, heat transfer limit and thermal resistance of MHP were improved about 10%. In the meantime, it is shown that the thermal resistance and heat transfer limit for the MHP with central wick type are higher than those of MHP with existing wick types. The results of performance test for MHP cooling modules with woven-wired wick to cool a notebook PC shows the stability as cooling system since T(sub)j(Temperature of Processor Junction) satisfy a demand condition of 0∼100$\^{C}$ under 11.5W of CPU heat.

• 한국축산식품학회지
• /
• 제28권3호
• /
• pp.295-300
• /
• 2008

This study was carried out to elucidate the relationship between different fat levels (0%, 5%, 10%, 15%, 20%, and 25%) and the quality of ground pork patties cooked to reach an internal temperature of $75^{\circ}C$ in a microwave oven. The relationship between fat level and cooking rate of pork patties cooked by microwave energy was highly significant ($R^2=0.72$), and had a low determination coefficient ($R^2=0.55$). The relationship between fat level and total cooking loss of pork patties cooked by microwave energy was also very significant, with a high correlation coefficient of $R^2=0.89$. The correlation coefficient between fat level and cooking drip loss of patties cooked by microwave energy was 0.92, which was highly significant. Although the correlation coefficient between fat level and evaporation loss had a negative value ($R^2=-0.63$), there was a highly significant relationship between fat level and shear force of pork patties cooked by microwave energy.

• Bulletin of the Korean Chemical Society
• /
• 제25권5호
• /
• pp.687-693
• /
• 2004

Composite membranes with a titania layer were prepared by soaking-rolling method with the titania sol of nanoparticles formed in the sol-gel process and investigated regarding the vapor permeation of various organic mixtures. The support modification was conducted by pressing $SiO_2$ xerogel of 500 nm in particle size under 10 MPa on the surface of a porous stainless steel (SUS) substrate and designed the multi-layered structure by coating the intermediate layer of ${\gamma}-Al_2O_3$. Microstructure of titania membrane was affected by heat-treatment and synthesis conditions of precursor sol, and titania formed at calcination temperature of 300$^{\circ}C$ with sol of [$H^+$]/[TIP]=0.3 possessed surface area of 210 $m^2$/g, average pore size of 1.25 nm. The titania composite membrane showed high $H_2/N_2$ selectivity and water/ethanol selectivity as 25-30 and 50-100, respectively. As a result of vapor permeation for water-alcohol and alcohol-alcohol mixture, titania composite membrane showed water-permselective and molecular-sieve permeation behavior. However, water/methanol selectivity of the membrane was very low because of chemical affinity of permeants for the membrane by similar physicochemical properties of water and methanol.

• 대한화학회지
• /
• 제59권6호
• /
• pp.488-492
• /
• 2015

본 연구에서는 칼슘채널 차단제로서 항고혈압 작용을 가진 (S)-(+)-pranidipine의 광학 분할에 의한 효과적인 제조방법을 제시하였다. (±)-Pranidipine을 가수분해시켜 얻은 monocarboxylic acid 5의 라세미 혼합물에 광학 활성이 있는 quinidine을 첨가하여 염을 형성한 다음 불용성 부분입체이성질체 염을 여과하고 염기와 산으로 처리하여 (R)-(-)-carboxylic acid 7을 분리하였고 이 carboxylic acid를 cinnamyl alcohol과의 에스터화 반응에 의해 (S)-(+)-pranidipine을 합성하였다. 이 화합물의 거울상 초과량(enantiomeric excess, ee)을 카이랄 HPLC로 분석한 결과 100% ee 값이 얻어졌고, 합성 과정에서 강염기 사용과 무수 조건 및 초저온 조건을 배제하였는바 이는 산업상 매우 유용한 개량방법이라 하겠다.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2003년도 하계학술연구발표회 및 한.일 공동심포지엄
• /
• pp.220-221
• /
• 2003

Equiatomic FePt and CoPt alloy thin films have received considerable attention as possible magnetic and magneto-optic recording because of their high magnetic anisotropy energy and high coercivity. The high coercivity in these thin films is due to the presence of finely dispersed ordered FePt phase mixed with disordered FePt phase. However, a high temperature treatment, either substrate heating during deposition or post annealing, is needed to obtain the ordered L1$\_$0/ phase with high value of magneto crystalline anisotropy. Recent microstructural studies on these films suggest that the average grain size ranges from 10-50 nm and the grains are magnetically coupled between each other. On the other hand, the ultrahigh-density magnetic recording media with low media noise imposes the need of a material, which consists of magnetically isolated grains with size below 10 nm. The magnetic grain isolation can be controlled by the amount of additional non-magnetic element in the system which determines the interparticle separation and therefore the interparticle interactions. Recently, much research work has been done on various non-magnetic matrices. Preliminary studies showed that the samples prepared in B$_2$O$_3$ and Carbon matrices have shown strong perpendicular anisotropy and fine grain size down to 4nm, which suggest these nanocomposite films are very promising and may lead to the realization of a magnetic medium capable of recording densities beyond 1 Tb/in$^2$. So, in this work, the effect of Carbon doping on the magnetic properties of FePt nanoparticles were investigated.

• Nuclear Engineering and Technology
• /
• 제23권3호
• /
• pp.352-362
• /
• 1991

가압 경수로의 노심 설계에 있어서 제한된 우라늄 자원의 효율적인 이용을 위한 다양한 방안으로 장주기 운전, 고연소도 및 저누출 장전 모형 통을 강구하고 있는 추세이다. 이러한 노심들은 원자로 운전 주기 전반에 걸친 공간적 출력 분포 제어와 잉여 반응도 제어를 위해 가연성 독물질을 사용하고 있다. 이와 관련하여 가연성 독물질 관리의 최적화 연구가 다각도로 진행되고 있다. 본 연구에서는 1990년도부터 국내 가압 경수로에 국산 핵연료가 장전되기 시작하면서 가도리니아 독봉을 사용하고 있으며 장차 주된 가연성 독물질로 쓰일 예정이므로 이에 대해서 분석을 수행하였다. 분석 결과 가도리니아 독봉은 열중성자 흡수 단면적이 매우 큰데서 기인한 특이한 연소 특성을 보이고 있다. 특히 집합체 내에서의 가도리니아 독봉의 위치에 따라 매우 다양한 출력 분포를 보이고 있다. 이러한 다양한 출력 분포 중에서 노심의 반경 방향 첨두 출력을 가능한 낮게하는 집합체 내에서의 가도리니아봉 위치 최적 선정을 위한 방법론을 제시하였다.

• 공업화학
• /
• 제5권3호
• /
• pp.509-516
• /
• 1994

에탄올의 제조시 불순물로서 미량 생성되는 크로톤 알데히드를 수소와 반응시켜 n-부틸알콜로 전환하여 불포화 탄화수소를 제거하는 공정에 액상수소 첨가반응을 이용하고자 하며, 기존의 기상 수소첨가반응보다 월등한 에너지 절약 효과가 있다. 반응촉매는 내구성 및 가격 등 경제적인 측면을 고려하여 니켈촉매를 선택하였으며, 반응전화율의 측정은 PMT(permanganate time) test 방법을 적용하였다. PMT는 에탄올에 미량으로 함유되어 있는 크로톤알데히드의 초기농도 증가에 따라 급격히 감소하였으며, 크로톤 알데히드로부터 n-부틸알콜로의 수첨반응은 탄소-탄소 이중결합의 환원 후, 알데히드의 환원 과정이 연속적으로 일어나고, 각 반응단계는 0차 반응속도 상수를 가진다. 실험조건 범위 내에서는 반응 온도가 높을수록, LHSV가 느릴수록 PMT는 길어지고, 반응압력은 PMT와 거의 무관함을 보였다.

• 한국도로학회논문집
• /
• 제14권5호
• /
• pp.93-99
• /
• 2012

PURPOSES: The purpose of this study is to compare the alkali-silica reactivity for mortar bar and concrete prism specimens using crushed aggregates of 5 types in Korea. And the alkali-silica reactivity for those aggregates are measured by chemical test method. METHODS: The alkali-silica reactivity for those aggregates was measured by chemical test method of KS F 2545, mortar-bar test of KS F 2546, accelerated mortar-bar test method of ASTM C 1260 and concrete prism test method of ASTM C 1293, relatively. RESULTS: The alkali-silica reactivity for those aggregates was verified by chemical test of KS F 2546 and accelerated mortar-bar test of ASTM C 1260. However, it was not by mortar-bar test of KS F 2546 and concrete prism test of ASTM C 1293. CONCLUSIONS: The above results showed that relationship among the four test methods were very low. The results from 3 types of test methods using cement-aggregate combinations appeared to be different. Because the environmental conditions of test methods for measuring the alkali-silica reactivity such as equivalent alkali content(external source), humidity, temperature, and times were different though the aggregates were same. Moreover, alkali-silica reactivity showed the biggest impact when alkalis were supplied form outside and exposed to environmental conditions. The accelerated mortar-bar test method seems to be most appropriate test method for concrete structures exposed to alkali environment.