• International Journal of Fluid Machinery and Systems
• /
• 제7권2호
• /
• pp.68-79
• /
• 2014

The type of turbine developed is based on the very low head of water potential source for the electric power production. The area of research is focused for the axial water turbine that can be applied at the simple site open channel with has a very low cost and environmental impact compared to the conventional hydro installation. High efficiency of axial turbine which applied to the very low potential head will made this type of turbine can be used at wider potential site. Existing irrigation weir and river area will be the perfect site for this turbine. This paper will compare the effects of the variation of swirl velocity criterion during the design of the blade of guide vane and rotor of the turbine. Effects of the swirl velocity criterion is wider known as a vortex conditions (free vortex, force vortex and swirl velocity constant), and the free vortex is the very popular condition that applied by most of turbine designer, therefore will be interesting to do a comparison against other criterion. ANSYS Fluent will be used for simulation and to determine the predictive performance obtained by each of design criteria.

• 한국유체기계학회 논문집
• /
• 제10권4호
• /
• pp.21-28
• /
• 2007

The ratio of disk friction loss in a centrifugal pump is very large for the total pump loss in the range of very low specific speed. Therefore, impeller radius should be shortened to increase the pump efficiency because the disk friction loss is proportional to the fifth power of impeller radius. In order to compensate the decreased head by the shortened impeller radius, vane angle at impeller outlet should be increased. However, as the vane angle at impeller outlet becomes larger, performance instability occurs at low flow rate regions. In this study, J-Groove is adopted to suppress the performance instability and detailed examination is performed for the influence of the J-Groove on the pump performance. The results show that J-Groove gives good effect on the suppression of performance instability. Moreover, as J-Groove increases pump head considerably, the pump size can be smaller for head requirements.

• 한국유체기계학회 논문집
• /
• 제17권4호
• /
• pp.30-39
• /
• 2014

The cross flow turbine is economical because of its simple structure. For remote rural region, there are needs for a more simple structure and very low head cross flow turbines. However, in this kind of locations, the water from upstream always flows into the turbine with some other materials such as sand and pebble. These materials will be damage to the runner blade and shorten the turbine lifespan. Therefore, there is a need to develop a new type of cross flow turbine for the remote rural region where there is availability of abundant resources. The new design of the cross flow turbine has an inlet open duct, without guide vane and nozzle to simplify the structure. However, the turbine with inlet open duct and very low head shows relatively low efficiency. Therefore, the purpose of this study is to optimize the shape of the turbine inlet to improve the efficiency, and investigate the internal flow of a very low head cross flow turbine. There are two steps to optimize the turbine inlet shape. Firstly, by changing the turbine open angle along with changing the turbine inlet open duct bottom line (IODBL) location to investigate the internal flow. Secondly, keeping the turbine IODBL location at the maximum efficiency achieved at the first step, and changing the turbine IODBL angle to improve the performance. The result shows that there is a 7.4% of efficiency improvement by optimizing turbine IODBL location (open angle), and there is 0.3% of efficiency improvement by optimizing the turbine IODBL angle.

• 한국항공우주학회지
• /
• 제37권11호
• /
• pp.1096-1103
• /
• 2009

연소기 헤드부는 극저온 유체인 액체산소가 고압으로 작동하고, 동시에 연소기의 추력으로 인한 하중을 받기 때문에, 극저온에서의 헤드의 구조 안정성 해석을 위한 재료의 변형 거동 예측은 매우 중요하다. 헤드부의 변형 거동을 예측하기 위해 재료의 저온에서의 인장 변형 거동을 묘사할 수 있는 구성 방정식을 Kocks의 전위 에너지 장벽 모델을 바탕으로 열적 요소와 비열적 요소의 결합으로 구성하였으며, 극저온에서 장애물들의 증가로 인한 응력의 열적 요소의 증가를 묘사하기 위해서, 장애물로 인해 발생하는 응력 요소를 Ramberg-Osgood 형태의 식으로 구성하였다. 본 모델은 극저온과 상온의 넓은 온도 영역에서 재료의 변형 거동을 잘 예측하였다.

• 대한기계학회논문집B
• /
• 제29권7호
• /
• pp.784-794
• /
• 2005

In the very low specific speed range ($n_s=0.24$ < 0.25, non-dimensional), the efficiency of centrifugal pump designed by a conventional method is very low in common. Therefore, positive-displacement pumps have long been used widely. Recently, since the centrifugal pumps are becoming higher in rotational speed and smaller in size, there expects to develop a new centrifugal pump with a high performance to replace the positive-displacement pumps. The purpose of this study is to investigate the internal flow characteristics of a very low specific speed centrifugal pump and to examine the effect of internal flow pattern on pump performance. The results show that the theoretical head definition of semi-open impeller should be revised by the consideration of high slip factor in the semi-open impeller, and the leakage flow through the tip clearance results in a large effect on the impeller internal flow. Strong reverse flow at the outlet of semi-open impeller reduces the absolute tangential velocity considerably, and the decreased absolute tangential velocity increasese the slip factor with the reduction of theoretical head.

• 대한기계학회논문집B
• /
• 제29권7호
• /
• pp.773-783
• /
• 2005

Internal flow measurement of very low specific-speed semi-open impellers has been carried out by PIV in order to understand better the internal flow patterns that are responsible fur the unique performance of these centrifugal pumps operating in the range of very low specific speed. Two types of impellers, one equipped with six radial blades (Impeller A) and the other with four conventional backward-swept blades (Impeller B), are tested in a centrifugal pump operating at a non-dimensional specific-speed of $n_s=0.24$. Complex flow patterns captured by PIV are discussed in conjunction with the overall pump performance measured separately. It is revealed that Impeller A achieves higher effective head than Impeller B even though the flow patterns in Impeller A are more complex, exhibiting secondary flows and reverse flows in the impeller passage. It is shown that both the localized strong outward flow at the pressure side of each blade outlet and the strong outward through-flow along the suction side of each blade are responsible for the better head performance of Impeller A.

• 방사성폐기물학회지
• /
• 제10권1호
• /
• pp.1-11
• /
• 2012

Rorabaugh(1953)에 의해 재정리된 단계양수시험 해석해 $s_w=BQ+CQ^p$는 단열암반대수층에서 비선형으로 증가하는 수위강하에 매우 적합하며, 현장에서 관측된 수위강하 값과 추정된 수위강하 사이의 제곱근 평균제곱오차(RMSE) 값이 매우 낮음을 보여주었다. 우물수두손실($CQ^p$)의 $C$ 값은 $3.689{\times}10^{-19}{\sim}5.825{\times}10^{-7}$, $P$ 값은 3.459~8.290의 범위로 산정되었으며, 지표로부터 하부심도로 내려 갈수록 양수율 증가에 따른 수위강하는 매우 크게 나타났다. 단열암반대수층에서의 우물수두손실은 다공질매질에서와 달리 단열특성(단열의 틈, 간격, 상호 연결성)에 의한 영향으로 나타나므로, 우물수두손실의 $C$ 와 $P$ 값은 단열암 반대수층의 난류구간과 고 저 투수성 단열암반의 특성을 해석하는데 매우 중요하다. 그 결과, 우물수두손실 항의 $C$ 와 $P$ 값에 대한 회귀분석 결과로부터 암반대수층의 난류구간과 수리특성의 관계가 파악되었으며, $C$ 와 $P$ 값의 관계가 단열암반대수층의 수리특성 해석에 있어 매우 유용함을 확인할 수 있었다.

• 한국유체기계학회 논문집
• /
• 제9권1호
• /
• pp.32-39
• /
• 2006

Recently, according to the trend of small size in scale and high speed in rotation of turbomachinery, very low specific speed centrifugal pump is taking a growing interest because the pump is characterized by high head and low flow rate with convenience of manufacturing and maintenance compared with conventional positive displacement pump. However, the efficiency of the very low specific speed centrifugal pump drops rapidly with the decrease of specific speed. The purpose of this study is nor only to examine the influence of casing type on the performance of centrifugal pump in the range of very low specific speed but also to determine the proper casing type for the improvement of pump performance. The results show that circular casing is suitable for the centrifugal pump in the range of very low specific speed and the influence of impeller configuration on the pump performance is very small. Radial thrust in the circular and volute casings is considerably small in the range of very low specific speed.

• 한국유체기계학회 논문집
• /
• 제17권5호
• /
• pp.19-26
• /
• 2014

The cross flow turbine attracts more and more attention for its relatively wide operating range and simple structure. In this study, a novel type of micro cross flow turbine is developed for application to a step in an irrigational channel. The head of the turbine is only H=4.3m and the turbine inlet channel is open ducted type, which has barely been studied. The efficiency of the turbine with inlet open duct channel is relatively low. Therefore, a guide nozzle on the turbine inlet is attached to improve the performance of the turbine. The guide nozzle shapes are investigated to find the best shape for the turbine. The guide nozzle plays an important role on directing flow at the runner entry, and it also decreases the negative torque loss by reducing the pressure difference in Region 1. There is 12.5% of efficiency improvement by attaching a well shaped guide nozzle on the turbine inlet.

• 대한두경부종양학회지
• /
• 제38권1호
• /
• pp.25-29
• /
• 2022

Parathyroid carcinoma is very rare malignant neoplasm, accounting for less than 0.005% of all cancers. Most parathyroid carcinoma is a functioning tumor that causes hyperparathyroidism, leading to hypercalcemia. We report a parathyroid carcinoma case that was suspicious for spontaneous infarction of cancer, leading to resolution of hypercalcemia. A 29-year-old male visited our hospital presenting with right neck swelling and pain. He has been experiencing frequent urolithiasis for four years but laboratory tests showed normal serum calcium level. Right vocal cord paresis was identified with laryngoscopy. Ultrasonography revealed a 3.7 × 3.5 cm mass in the right thyroid containing a focal cystic portion. Computed tomography confirmed the presence of a low-density right thyroid mass. Right thyroid lobectomy was performed and pathological evaluation revealed parathyroid carcinoma with central necrosis. We report this very rare case with a literature review.