• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.7
• /
• pp.1057-1066
• /
• 2001

This paper describes a design for linear polarization antenna using the EMCD (electromagnetically coupled dipole). The analysis and the design of model antennas are conducted by FDTD method. Vertical and horizontal linear polarizations are easily obtained by variation of dipole position. In 1-element antenna design, mutual coupling between microstrip feed line and radiator is considered. Design parameters of each 1-element antenna with vertical and horizontal polarization are used for array design. Radiation power and main beam tilting angle can be controlled by the offset and the distance between radiating elements in an array, respectively. 5-element array antennas are fabricated and measured to prove the design validity. The results of FDTD simulation and measurement show the reasonable agreement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.2
• /
• pp.144-150
• /
• 2012

In this paper, circularly polarization patch array antenna of RSE(Road-side Equipment) base station for DSRC(Dedicated Short Range Communication) of ITS(Intelligent Transport System) is proposed. The antenna of RSE base station for DSRC is designed to operate circularly polarization to receive reflected signal from multiplex path effectively. The proposed antenna consisted of microstrip patch and feed line, the slit is inserted in the proximity of the slot of feed structure to generate circularly polarization. The $2{\times}2$ array structure is designed to satisfying gain that DSRC RSE base station antenna required. Measured impedance bandwidth and axial-ratio bandwidth are satisfied by all DSRC band of 5.795~5.855 GHz. Vertical and horizontal HPBW of the proposed antenna are both about 43 degrees, it showed gain characteristic of about 11.21 dBi.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.3
• /
• pp.261-268
• /
• 2016

In this paper, dual-polarized monopulse cassegrain antenna for W-band millimeter-wave seeker was proposed and the performances were verified by the measured results of the fabricated antenna. Dual-polarized monopulse Cassegrain antenna consists of main/subreflector, dual-polarized feed horn and monopulse comparator. The proposed feed horn has $2{\times}2$ array square waveguide feeding structure to make monopulse signals and it was designed using 90 degree rotational symmetric structure to receive dual-polarized signals. At the sum and difference channel, the measured vertical and horizontal polarization radiation pattern were similar. Measurement gains are 35.1 dBi for v-pol. and 35.6 dBi for h-pol. at the center frequency with 0.5dBi difference between each polarization and the side lobe level is below -21.6 dB.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.1
• /
• pp.34-48
• /
• 2017

This study proposes a new approach to control a trajectory control of vertical type articulated robot arm with six revolution joints by computed torque method for manufacturing process automation. The proposed control scheme takes advantage of the properties of the fuzzy controllers. The proposed method is suitable to control of the trajectory and path control in cartesian space for vertical type articulated robot manipulator for forging manufacturing process automation. The results is illustrated that the proposed fuzzy computed torque controller is more stable and robust than the conventional computed torque controller. This study is included with an analytical methodology of inverse kinematic computation for 6 DOF manipulators. And an intelligent PID based on feed forward fuzzy control structure is applied to control the working path control with disturbances caused by uncertainty parameters of the manipulator dynamic model. Lastly, the validity of proposed is verified by simulations and experiments.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.5
• /
• pp.415-423
• /
• 2020

GNSS (Global Navigation Satellite System) is mostly used for high-precise surveys due to its accuracy and efficiency. But this technique does not always fulfill the demanding accuracy in harsh operational environments such as urban canyon and forest. One of the remedies for overcoming this barrier is to compose a heterogeneous surveying network by adopting terrestrial measurements (i.e., distances and angles). Hence, this study dealt with the adjustment of heterogeneous surveying networks consisted of GNSS baseline vectors, distances, horizontal and vertical angles with a view to enhancing their accuracy and so as to derive an appropriate scheme of the measurement combination. Reviewing some technical issues of the network adjustments, the simulation, and experimental studies have been carried out, showing that the inclusion of the terrestrial measurements in the GNSS standalone overall increased the accuracy of the adjusted coordinates. Especially, if the distances, the horizontal angles, or both of them were simultaneously adjusted with GNSS baselines, the accuracy of the GNSS horizontal component was improved. Comparing the inclusion of the horizontal angles with those of the distances, the former has been more influential on accuracy than the latter even though the same number of measurements were employed in the network. On the other hand, results of the GNSS network adjustment together with the vertical angles demonstrated the enhancement of the vertical accuracy. As conclusion, this paper proposes a simultaneous adjustment of GNSS baselines and the terrestrial measurements for an effective scheme that overcomes the limitation of GNSS control surveys.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.361-366
• /
• 2005

In this paper, a modified multimode hem antenna is designed to have 142 mm horn aperture radius and 921 mm length in order to be safe under 100 MW peak pulse power at 3 cm wave length through breakdown phenomenon study that threshold field strengths for the air breakdown phenomena is decided to be 3.78 MV/m. The proposed antenna is measured gain over 27 dBi and the -25 dB beam width of 29$^{\circ}$ in vertical plane.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.128-131
• /
• 2000

This paper describes design for dual-linear polarization antenna using EMC(electromagnetic-coupled) dipole. EMC dipole has a simple element structure and it is fed by microstrip line. Vortical and horizontal polarization are determined by structure of dipole fed by microstrip line. FDTD Method is used for an analysis of antenna element. Length, width, height and offset of dipole are designed for 1-element antenna. Resonant length of diploe differs from the calculated value by a formula because of coupling effect of dipole and feed line. Radiation Power is controlled by the offset of dipole. In prectical fabrication of antenna array, a constant height of dipoles is required. Therefore, the teflon plate with height of 0.8 mm is considered in antenna element design for the vertical polarization.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1855-1857
• /
• 2001

An Inverted-F antenna for the 2.4GHz application is designed and implemented. The antenna is implemented on the PCB board and installed in a vertical position. The 10dB characteristics are 2.4 to 2.48GHz in bandwidth which satisfies the bluetooth requirement and the whole impedance is matched. The feed-line on the PCB board is also calculated and implemented. And the measuring system is installed at the KITI in Kangwon Nat'l Univ. and applied to measured the antenna characteristics. The measured values show that this antenna is suitable for the commercial applications.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.455-459
• /
• 1997

A methodology which supports the feature used from design to manufacturing for sculptured pocket is newly devlored and present. The information contents in a feature can be easily conveyed from one application to another in the manufacturing domain. However, the feature generated in one application may not be directly suitable for another whitout being modified with more information. Theobjective of the paper is to parsent the methodology of decomposing a bulky feature of sculptured pocket to be removed into compact features to be efficiently machined. In particular, the paper focuses on the two task: 1) to segment horizontally a bulky feature into intermediate features by determining the adequate depth of cut and cutter size and to generate the temporal precedence graph of the intermediate features and 2)to further decompose each intermediate feature vertical into smaller manufacturing features and to apply the variable feed rate to each small feature. The proposed method will provid better efficiency in machining time and cost than the classical method which uses a long string of NC codes necessary to remove a bulky fecture.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.2
• /
• pp.47-52
• /
• 2015

In this paper, the performance of uncoated- and Titanium nitride aluminium TiAlN-PVD coated- carbide twist drills were investigated when drilling aluminium alloy, Al 6061. This research focuses on the optimization of drilling parameters using the Taguchi technique to obtain minimum surface roughness and thrust force. A number of drilling experiments were conducted using the L9 orthogonal array on a CNC vertical machining center. The experiments were performed on Al 6061 material l blocks using uncoated and coated HSS twist drills under dry cutting conditions. Analysis of variance(ANOVA) was employed to determine the most significant control factors. The main objective is to find the important factors and combination of factors influence the machining process to achieve low surface roughness and low cutting thrust force. From the analysis of the Taguchi method indicates that among the all-significant parameters, feed rate are more significant influence on surface roughness and cutting thrust than spindle speed.