• Journal of Plant Biology
• /
• v.16 no.3_4
• /
• pp.17-34
• /
• 1973

The physico-chemical factors, the distribution of chlorophyll and the primary production of the lakes Hwajinpo, Yongrangho, Chunchonho, Uiamho, Soyangho and Changjamot have been studied in order to make ecological comparison among these lakes during summer stagnation period of August to September of 1973. On the basis of the characteristics of these lakes, the lake types have been discussed. Thermocline is observed at 3-4m zone in the lake Changjamot and 4-5m zone in the lake Yongrangho. In the case of lake Hwajinpo and impoundments, the distinct thermal stratification is not observed at the summer stagnation period. As to vertical distribution of dissolved oxygen, a positive heterograde curve is obtained in the lakes Hwajinpo and Yongrangho. In the lake Changjamot the typical clinograde curve and the oxygen depletion in hypolimnion are observed. In the case of impoundments, however, the orthograde curve is observed in the lakes Chunchonho and Uiamho. While in the lake Soyangho, any stratification of the disssolved oxygen is not found. In the brackish lakes, such as lakes Hwajinpo and Yongragho, the salinity of hypolimnion is found to be much higher than that of epilimnion. In the lake Hwajinpo, the salinity of hypolimnion is exhibited 32.7$\textperthousand$, which is nearly the same as sea water. The distribution of nitrogenous compounds and phosphates is found to be high in the lake Changjmot. The silicate is also found in high concentration in the lake Chunchonho, and the distribution of nutrients in the brackish lakes is generally low. As to the vertical distribution of chlorophyll level, the lake Changjamot shows a stratum type and the brackish lakes L-type stratification. In the impoundments, lakes Chunchonho and Uiamho appear to be homogeneous type. Seasonal variation of chlorophyll level in the lake Changjamot is examined from January to September 1973. The vertical distribution of chlorophyll during the period of circulation from January to April is homogeneous type and is stratum type thereafter. The maximum chlorophyll level is 277.4mg/$m^2$ on June 23 and the pattern of seasonal variation of chlorophyll level is comparable to the type of eutrophy. The horizontal distribution of chlorophyll level is studied in the brackish lakes, Hwajinpo and Yongrangho. The pattern of distribution is found to be an irregular type. On the basis of measurements of primary production by means of the carbon-14 method and the distribution of chlorophyll level, it is concluded that the interior part of the lake Hwajinpo and Changjamot are eutrophic and the exterior part of the lake Hwajinpo, lake Yongrangho and the impoundments, lake Uiambo and Soyangho are mesotrophic.

• The Journal of Korean Academy of Prosthodontics
• /
• v.33 no.1
• /
• pp.130-143
• /
• 1995

The purpose of this study was to analyze the magnitude and distribution of stress using photoelastic model with the rigid connection using T-block attachment and non-rigid connection using key & keyway attachment. The vertical load of 16 Kg was applied on the central fossa of the tooth, the pontic and the implant, and the pattern and distribution under each condition was analyzed. The following results were obtained : 1. In case of vertical load on the central fossa of the implant, the stress was concentrated at the apex of the implant involving the mesial alveolar bone in both fixed partial denture with the rigid connection and that with the nonrigid connection and the stress concentration at the mesial cervical area of the implant was a little more in the nonrigid connection than in the rigid connection. 2. In case of vertical load on the central fossa of the pontic, the stress was concentrated at the apex of 2nd bicuspid in both 3 unit fixed partial denture with nonrigid connection and that with the rigid connection. The stress was more concentrated at the mesial alveolar bone of the implant, but the stress distribution at the natural teeth more favorable at the rigid connection than at the non-rigid connection in case of 4 unit fixed partial denture. 3. In case of vertical load of the central fossa of the 2nd bicuspid, much stress with 3 fringe order was observed at the apex of the 2nd bicuspid in the 3 unit fixed partial denture, but relatively even stress distribution was observed at the apex of the implant, the 1st and 2nd bicuspid, and the adjacent cuspid in the 4 unit fixed partial denture.

• Journal of Wetlands Research
• /
• v.10 no.2
• /
• pp.23-37
• /
• 2008

The vertical distribution of dioxins and hexachlorobenzene(HCB) in a sediment core was investigated to elucidate historical trends of dioxins and HCB deposited into Upo wetland. The total concentration of dioxin ranged from 8.7 to 66.27 pg/g-dw in Upo sediments deposited, and from 17.64 to 97.03 pg/g-dw in Mokpo. Dioxin fluxes increased from the first-1990s and then reached a maximum in the mid-1990s. The major source of dioxin by comparing the congeners pattern was pentachlorophenol(PCP) used of agrochemicals. The HCB concentration in most of samples was detected below the MDL(Method Detection Limit of 0.5ng/g), except a few samples.

• 한국해양학회지
• /
• v.22 no.3
• /
• pp.119-129
• /
• 1987

Sediments in the cores from the KONOD-1 area consist mainly of authigenic smectite and clinoptilolite, and terrigenous minerals of illite, chlorite, kaolinite, quartz, and plagioclase. The authigenic minerals become dominant over the terrigenous minerals with increasing depth. Clinoptilolite occurs at the deeper core depth because its formation is slower than that of smectite. The vertical distribution of minerals indicates that the eolian influence, probably in the late Oligocene, diluted the abundance if smectite in near-surface sediments. This vertical distribution pattern may also have been affected by progressive dissolution of authigenic minerals in the near surface sediments.

• The Journal of Korean Academy of Prosthodontics
• /
• v.34 no.1
• /
• pp.101-124
• /
• 1996

In this study, we designed the finite element models of mandible with varying their connecting types between the prosthesis on implant fixture and 2nd premolar, which were free-standing case(Mf), precision attachment case(Mp), semiprecision attachment case(Ms) and telescopic case(Mt). The basic model of the designed finite element models, which contained a canine and the 1st & 2nd premolar, was implanted in the edentulous site of the 1st & 2nd molar by two implant fixtures. We applied the load in all models by two ways. A vertical load of 200N was applied at each central fossa of 2nd premolar and 1st implant. A tilting load of 20N with inclination of $45^{\circ}$ to lingual side was applied to buccal cusp tips of each 2nd premolar and 1st implant. And then we analyzed three-dimensional finite element models, making a comparative study of principal stress and displacement in four cases respectively. Three-dimensional finite element analysis was performed for the stress distribution and the displacement using commercial software(IDEAS program) for SUN-SPARC workstation. The results were as follows : 1 Under vertical load or tilting load, maximum displacement appeared at the 2nd premolar. Semiprecision case showed the largest maximum displacement, and maximum displacement reduced in the order of precision attachment, free-standing and telescopic case. 2. Under vertical load. the pattern of displacement of the 1st implant appeared mesio-inclined because of the 2nd implant splinted together. But displacement pattern of the 2nd premolar varied according to their connection type with prosthesis. The 2nd premolar showed a little mesio-inclined vertical displacement in case of free-standing and disto-inclined vertical displacement due to attachment in case of precision and semiprecision attachment. In telescopic case, the largest mesio-inclined vertical displacement has been shown, so, the 1st premolar leaned mesial side. 3. Under tilting load, The pattern of displacement was similar in all four cases which appeared displaced to lingual side. But, the maximum displacement of 2nd premolar appeared larger than that of the first implant. Therefore, there was large discrepancy in displacement between natural tooth and implant during tilting load. 4. Under vertical load, the maximum compressive stress appeared at the 1st implant's neck. Semiprecision attachment case showed the largest maximum compressive stress, and the maximum compressive stress reduced in the order of precision attachment, telescopic and free-standing case. 5 Under vertical load, the maximum tensile stress appeared at the 2nd implant's distal neck. Semiprecision attachment case showed the largest maximum tensile stress, and the maximum tensile stress reduced in the order of precision attachment, telescopic and free-standing case. 6. Under vertical load or tilting load, principal stress appeared little between natural tooth & implant in free-standing case, but large principal stress was distributed at upper crown and distal contact site of the 2nd premolar in telescopic case. Principal stress appeared large at keyway & around keyway of distal contact site of the 2nd premolar in precision and semiprecision attachment case, appearing more broad and homogeneous in precision attachment case than in semiprecision attachment case.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.4
• /
• pp.505-514
• /
• 1998

Flow pattern of air-water two phase flow depends on the conditions of pressure void fraction and channel geometry. We classify the flow pattern by measuring the output signal of the conductivity probe. under the classified flow pattern we mount a visualization equipment on the test section and take pictures. We vary the concentration of pure solvent and polymer to measure local void fraction. We know that the maximum point position of local void fraction distribution move from the center of the pipe to the wall of the pipe as JSL increase when JSA is constant in two phase flow. But we find that the maximum point position of local void friction move from the wal of the pipe to the center of the pipe when polymer concentration increase.

• The Korean Journal of Zoology
• /
• v.15 no.2
• /
• pp.87-91
• /
• 1972

For the geographical distribution of Primno macropa it was distributed over all stations investigated, except surface tow in East China Sea, through all seasons. It is believed that this species is most cosmopolitan species in the western North Pacific. Veritical distributional range of P. macropa indicates at depths from surface to more than 1,500m and most deeper recored for the vertical occurrence was obtained from depth of 1,650-2,220m in Station 229 $(34^\\circ 44.3'N, 140^\\circ 04.4'E)$, off Nojima-Zaki, Central Japan. For the vertical distributional and migrational pattern it is a typical diurnal migrant in the western North Pacific; at depths from 100m to 500m at night and 400m to 700m at day in Oyashio population, and from surface to 200m at night and from 100m to 300m at day in Kuroshio population. In Kuroshio area, the population of P. macropa was distributed in somewhat shallower layers than in Oyashio area and it is suggested that the populations is different in region and season according to their stages consisting the population.

• The Journal of Korean Academy of Prosthodontics
• /
• v.31 no.1
• /
• pp.129-150
• /
• 1993

Since the restoration or masticatory function is the most important aim of implants, it should be substituted for the role of natural teeth and deliver the stress to the bone under the continous load during function. In natural teeth, stress distribution can be obtained through enamel, dentin and cementum and the elasticity of the periodontal ligament play a role of buffering action. In contrast, implant prosthesis has a very unique characteristics that it delvers the load directly to bone through the implant and superstructure. This fact arise the needs to evaluate the stress distribution of the implant in the mechnical aspects, which has a similar role of natural teeth but different pathway of stress. With 3 kinds of implant in prevalent use, 2 types of experimental PEA implant models were made, axisymmetric and 2-dimensional type. In axisymmetric model, the stiffness of the part including the prosthesis and implant which extrude out of bony surface could be calculated with displacement of the superstructure un er 100N vertical load and then damping effects could be determined through this stiffness. In axisymmetric FEA model, load to the bone could be deduced by evaluation the stress distribution of the designed surface under the 100N vertical force and in 2-dimensional model, 100N eccentric vertical load and 20N horizontal loda. The result are as follows. 1. In every implant, stress to the bone tends to be concenturated on the cortical bone. 2. Though the stress of the cancellous bone is larger at the apex of implants, it is less compared with cortical bone. 3. Under 20N horizontal load, stress of the left and right sides of implant shows a symmetrical pattern. But under 100N eccentric vertical load, loaded side shows much larger stress value. 4. In the 1mm interface, stress distribution among implants tend to have a similar pattern. But under 20N horizontal load apposite side of being loaded shows less stress in IMZ. 5. In the case of screw type implant, stress tends to vary along with screw shape. 6. According to the result determined with microstrain, cancellous bone id generally under the condition of overload, while cortical bone is usually within the limitation of physiologic load. 7. In the Branemark implant, maximum stress to the cortical bone is larger than any other implant except for the condition of 20N horizontal force and 0.05mm interface. 8. Damping effects of implants is maximum in IMZ.

• The Journal of the Petrological Society of Korea
• /
• v.18 no.2
• /
• pp.115-135
• /
• 2009

We have studied general orientational characteristics of microcracks distributed in Tertiary crystalline tuff from the northeastern part of the Gyeongsang Basin. 108 sets of microcracks on horizontal surfaces of 6 rock samples from Heunghae-eup and Cheongha-myeon, Pohang-si areas were distinguished by image processing. Those microcrack sets show a distinct linear array in 38 images. Whole domain of the directional angle(${\theta}$)-frequency(N) chart for crystalline tuff can be divided into 20 domains in terms of the phases of the distribution of microcracks. From the related chart, microcrack sets show preferred orientation which are coincident with the direction of vertical common joints. Consequently, the potential for macroscopic vertical joints in a rock body can be inferred from the directional angle showing high frequency in each domain of the related chart. This joint pattern is nearly the same in Mesozoic granites from Seokmo-do, Gwanghwa-gun. From the rose diagram for orientations of microcrack in crystalline tuff, orientations of dominant sets of microcracks in terms of frequency orders reflect representative orientations of maximum principal stress acted on crystalline tuff. Meanwhile, orientations of microcracks in crystalline tuff were compared with those of open microcracks in Bulgugsa granites from the southwestern part of the Gyeongsang Basin, and vertical rift/grain planes from Mesozoic granite quarries in Korea. In regional distribution chart, the agreement of distribution pattern between above two types of microcrack sets and vertical planes suggests that microcrack systems developed in crystalline tuff probably occur regionally in Mesozoic granites in Korea.

• Ocean and Polar Research
• /
• v.24 no.4
• /
• pp.457-464
• /
• 2002

Distribution and stock assessment of mega-benthos living in the shallow hard bottom around Dokdo were studied in July,2000. Depth and topographical conditions have affected to the densities and biomass of benthic animals. In shallow area, less than 10 m depth, turbo shell Batillus cornutus, mussel, Mytilus corusucs were dominated and showed distinct patterns in vertical distribution. On the other hand, the area over 10m depth, it showed diverse pattern depending on topography. Turbo shell, mussel and sea cucumber Stichopus japonicus were dominated in terms of fishery resources, but abalones were rarely sampled. Stock assessment were estimated to be 6.54 M/T, 3.89 M/T and 8.92 M/T, respectively. Some parts of coastal hard bottom around Dokdo, such as the area between Dongdo and Seodo, seemed to play an Important role as nursery ground. Therefore, it is necessary to the environmental monitoring for coastal fishery managements aspects.