• 대한기계학회논문집B
• /
• 제33권3호
• /
• pp.164-169
• /
• 2009

The slip velocity and the temperature jumps for low-speed flow in microchannels are investigated using Langmuir slip boundary condition. This slip boundary condition is suggested to simulate micro flow. The current study analyzes Langmuir slip boundary condition theoretically and it analyzed numerically micro-Couette flow, micro-Poiseuille flow and grooved microchannel flow. First, to prove validity for Langmuir slip condition, an analytical solution for micro-Couette flow is derived from Navier-Stokes equations with Langmuir slip conditions and is compared with DSMC and an analytical solution with Maxwell slip boundary condition. Second, the numerical analysis is performed for micro-Poiseuille flow and grooved microchannel flow. The slip velocity and temperature distribution are compared with results of DSMC or Maxwell slip condition and those are shown in good agreement.

• 한국기계연구소 소보
• /
• 통권18호
• /
• pp.29-35
• /
• 1988

When low sliding velocities in the boundary lubrication range are operating, irregular movements frequently occur which are a result of the stick-slip phenomenon. Such slide motions are undesirable in precision machine tools, particularly with feed back systems used in numerical and adaptive control machine tools. Accordingly, this paper reports analytical and experimental studies in the stick-slip characteristic of machine tool feeding system. The main conclusions of this study are as follows; The tendency towards stick-slip effects may be reduced by; 1). Reducing the drop in friction coefficient in the Stribeck curve(on the rising part of the friction characteristic at higher sliding speeds, the system is stable all the time) 2). Reducing the transition velocity by the use of a higher viscosity lubricating oil. 3). Increasing the stiffness(Damping)and reducing normal load(Sliding mass) Therefore, the Critical velocity is decided from the above conclusions and in designing of machine tool, feed rates(sliding velocity)must be design the more than critical velocity.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.50-52
• /
• 2004

Mobility of an indoor wheeled robot is affected by adhesion force that is related to various floor conditions. When the adhesion force between driving wheels and the floor decreases suddenly, the robot has slip state. First of all, this paper models adhesion characteristics and slip in wheeled robot. Secondly, the paper proposes estimation method of adhesion force coefficient according to slip velocity. In oder to overcome this slip problem, optimal slip velocity must be decided for stable movement of wheeled robot. The paper proposes an anti-slip control system based on an ordinary disturbance observer, that is, the anti-slip control is achieved by reducing the driving torque enough to give maximum adhesion force coefficient. These procedure is implemented using a Pioneer 2-DXE parameter.

• 대한토목학회논문집
• /
• 제32권5D호
• /
• pp.483-492
• /
• 2012

슬립폼 공법에 있어서 초기경화시간은 콘크리트가 거푸집에서 안전하게 빠져나올 수 있는 굳기를 갖게 되는 콘크리트 타설 후 경화시간으로써 슬립폼 시스템의 상승속도를 결정하는 중요한 요소이다. 따라서 슬립폼 시스템의 안전성 확보와 콘크리트의 시공품질을 확보하도록 초기경화시간을 파악하는 기술이 필요하다. 본 논문에서는 초음파를 이용하는 기법 중 표면파 속도를 이용하여 콘크리트의 경화정도를 파악하여 초기경화시간을 추정함으로써 슬립폼 시스템의 상승 시기를 결정하는 연구를 수행하였다. 관입저항시험과 압축강도시험을 수행하여 콘크리트의 초기경화시간과 압축강도와의 관계를 규명하였고, 또한 압축강도와 표면파 속도와의 관계를 규명하기 위해 초음파시험을 동시에 수행하였다. 표면파 속도를 측정하기 위해 연속웨이블릿변환을 사용하였으며, 이때 수치해석을 통해 연속웨이블릿변환의 사용에 대한 타당성을 입증하였다. 이로부터 슬립폼 시스템의 상승에 요구되는 표면파 전파속도를 제안하였으며, 슬립폼 시스템의 축소모형실험을 수행하여 제안한 표면파 속도가 슬립폼 상승 시기를 결정하는데 사용될 수 있음을 입증하였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.371-376
• /
• 1999

Stick-slip friction is present to some degree in almost all actuators and mechanisms and is often responsible for performance limitations. Simulation of stick-slip friction is difficult because of strongly nonlinear behavior in the vicinity of zero velocity. A straightforward method for representing and simulating friction effects is presented. True zero velocity sticking is represented without equation reformulation or the introduction of numerical stiffness problems. Stick-slip motion is investigated experimentally, and the fundamental characteristics of the stick-slip motion are clarified. Based on these experimental results, the characteristics of static in the period of stick and kinetic friction in the period of slip are studied concretely so as to clarify the stick-slip process.

• 수산해양기술연구
• /
• 제17권2호
• /
• pp.85-91
• /
• 1981

평판 강괴를 연속적으로 주조할 경우에 초기주조 상태에서 Mold 내부의 Support bar 및 용강자중, 주조속도, 용강두께, 이를 지지하는 제어 Roller, 유압기구, 구동 Motor, 그리고 주조조직의 응고 등이 용강의 인발력을 유도하는 Pinch Roller와의 사이에서 동력학적 부평형을 일으켜 Slip 현상을 초래하므로 본 논문에서는 이상의 제요인들을 근거로 Slip 현상을 규명하는 식을 유도하고 강괴의 주조속도, 비중량, 두께의 변화에 대한 Slip Force 거동을 규명하였다. 그 결과 1. 본 논문의 해석식에 의하여 평판강괴 연속주조용 Pinch Roller의 적정압을 설계할 수 있다. 2. 비중량은 순수히 자중만 증가시키는 요인이며 Slip Force는 주조속도변화에 대해서 포물선적으로 증가한다. 3. 주조두께 및 비중량의 변화에 대한 Slip Force는 이에 비례하여 증가하나 특히 두께의 값이 소폭보다 대폭에서 그 변화 값이 크게 나타났다.

• 전기학회논문지
• /
• 제67권10호
• /
• pp.1308-1316
• /
• 2018

Accurate tuning of parameter is very important in vector-controlled induction motor. Among the parameters of induction motor, detuning of rotor resistance used in controller design deteriorates drive performance. This paper presents a novel rotor resistance estimation strategy using slip angular velocity in vector-controlled induction motor drives. The slip angular velocity can be calculated by two methods. Firstly, it can be induced from the rotor voltage equation. Secondly, it can be induced from the difference between synchronous angular velocity and rotor angular velocity. The first method includes the rotor resistance, while the second method dose not include this parameter. From this fact, the rotor resistance can be identified by comparing the slip angular velocities in the two methods. In the tuned states of the rotor resistance, performances of flux estimator and speed drive are discussed. The simulation and experimental results are given to verify the validity of the proposed method in various situations.

• 대한인간공학회지
• /
• 제20권2호
• /
• pp.47-57
• /
• 2001

To simulate an actual slip to measure floor slipperiness, slip resistance testers simulate slip in only forward direction because forward slip in the landing phase was found to be the most important factor for loss of balance. Backward slip in the take off phase was possible but was excluded in the friction test protocol because it was not dangerous. However, backward slip was tested in the friction test protocol without any theoretical background of the significance in generating dangerous slips and falls and was proven to be as good as forward slip in measuring floor slipperiness. Therefore, this study was designed to investigate the significance of backward slip in generating dangerous slips and falls with different combinations of floor and shoe sole. The results showed different tendency of backward slip in take off phase being significant in generating dangerous slips and falls because backward slip in the takeoff phase affected gait pattern disturbances seriously. resulted in dangerous falls. Fast toe velocity increased the severity of backward slip and confirmed the significance of backward slip in generating dangerous slips and falls. As a result, this study recommends the utilization of backward slip in the measurement of floor slipperiness.

• 한국전산유체공학회지
• /
• 제19권2호
• /
• pp.40-48
• /
• 2014

For rarefied gas flow regimes, physical phenomena such as velocity slip and temperature jump occur on the solid body surface. To predict these phenomena accurately, either the Navier-Stokes solver with a slip boundary condition or the direct simulation Monte Carlo method should be used. In the present study, flow simulations of a wedge were conducted in Mach-10 flow of argon gas for several different flow regimes using a two-dimensional Navier-Stokes solver with the Maxwell slip boundary condition. The results of the simulations were compared with those of the direct simulation Monte Carlo method to assess the present method. It was found that the values of the velocity slip and the temperature jump predicted increase as the Knudsen number increases. Also, the results are comparatively reasonable up to the Knudsen number of 0.05.

• Korea-Australia Rheology Journal
• /
• 제17권4호
• /
• pp.207-215
• /
• 2005

We present a finite difference solution for electrokinetic flow in rectangular microchannels encompassing Navier's fluid slip phenomena. The externally applied body force originated from between the nonlinear Poisson-Boltzmann field around the channel wall and the flow-induced electric field is employed in the equation of motion. The basic principle of net current conservation is applied in the ion transport. The effects of the slip length and the long-range repulsion upon the velocity profile are examined in conjunction with the friction factor. It is evident that the fluid slip counteracts the effect by the electric double layer and induces a larger flow rate. Particle streak imaging by fluorescent microscope and the data processing method developed ourselves are applied to straight channel designed to allow for flow visualization of dilute latex colloids underlying the condition of simple fluid. The reliability of the velocity profile determined by the flow imaging is justified by comparing with the finite difference solution. We recognized the behavior of fluid slip in velocity profiles at the hydrophobic surface of polydimethylsiloxane wall, from which the slip length was evaluated for different conditions.