• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.222-229
• /
• 2000

Malty bridges are severely damaged by the overloaded heavy vehicle and tile trend will become more serious because the traffic volume is continuously increasing. Currently, the vehicles with gross weights over 40 tons or axle weight over 10 tons are not allowed on the public road. However, this regulation is not based on a systemetic study on the bridge capacityand assumed to be much too conservative depending on the vehicle types ans bridge types. In this study, the permit weights of heavy vehicles of diverse axle spacings and axle load distribution are calculated considering the structural characteristics of bridge superstructures. In order to consider the various load effects of heavy weight vehicle crossings, three conditions are considered in the calculation of permit vehicle load. From the results, the permit vehicle weights of bridges are calculated and simplified formulas which can be used in the case when only the vehicle dimension are known are presented.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.04b
• /
• pp.7-7
• /
• 2002

Recently social demand to achieve low fuel consumption and clean emission requires the development of new generation vehicle beyond the conventional vehicle concept. In this point, new generation vehicle is newly designed as electric vehicle, hybrid electric vehicle, fuel cell electric vehicle or 3 liter car etc. In order to develop new generation vehicle, it is very important to develop new materials and process technologies now. In this paper these new technologies are presented focusing on weight reduction specially. Steel body can be achieved 20-25% weight reduction by adoption of high strength steel and new process technologies, i.e tailored blank and hydroforming. Aluminium body can be achieved 40-50% weigt down by use of all aluminium monocoque body or aluminium space frame with aluminium panel. Plasitic composite body can be achieved 30% weight reduction comparing with conventional steel body.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.303-303
• /
• 2000

It is difficult to determine the static axle weight of a vehicle with weigh-in-motion systems which in absence measure instantaneous axle impact forces. The difficulty in determining a static axle weight results from dynamic effects induced by vehicle/road interactions. One method to improve the problem is to quantify a statistical confidence level for measured axle weight. The quarter-car model is used to simulate vehicle motion, Also, the road input to vehicle model can be characterized in statistical terms by PSD (power spectral density) of appropriate amplitude and frequency contents other than an exact spatial distribution. The confidence levels for the measured axle weight can be obtained by the random process analysis using both vehicle model and road input.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.9
• /
• pp.723-734
• /
• 2018

A structural weight estimation methodology for the multicopter design process is presented. In general, a multicopter is composed of an airframe, motors, propellers, battery and so on. Among these, the weight of motors, propellers and battery can be obtained from the weight trends with respect to design parameters. However, the structural weight is hard to be estimated due to the various configurations and design concepts of multicopters. Moreover, the airframe weights of most commercial multicopter products are not provided. Thus, an accurate airframe weight model is required for the reliable mutlcopter design process. Firstly, the standard configuration of multicopters is defined. Then, we proposed the structural weight estimation method using the number and diameter of propellers determined from the initial step of sizing process. Finally, we validated our suggested method using the commerical products.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.169-173
• /
• 2008

This study is concerned with adopting the hydroforming method in the front axle of the commercial vehicle. Generally the front axle of the commercial vehicle is made bγ the several operations of press forging. This product supports the big weight of the vehicle and load. The weight of the press forging parts is also so more than it of the press parts of the passenger car. So, we have studied the hydroforming method to lessen the weight of the front axle of the commercial vehicle. To apply the hydroforming method in the commercial vehicle, we had to use the operation of reducing the diameter of the used tube prior to the hydorforming operation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.1
• /
• pp.40-49
• /
• 2004

In this paper, vibration response of aerial gas pipeline due to vehicle loads was quantitatively estimated through experiment and analysis in open cut construction site. The vehicle vibration of various construction machines causes serious effect to the aerial gas pipeline. The new vibration prediction equations presented in this study can estimate the vibration velocity response of the aerial gas pipeline. In the nitration prediction equations, the vehicle′s weight and traveling velocity, which are the sources of vibration, are combined into the term called, "scaled weight" Methods to reduce vibration were proposed in case the vibration velocity response of the gas pipeline exceeded the vibration criterion, using the vibration prediction equations presented in this study. One was to limit the vehicle′s traveling velocity and the other to install the isolation equipment. Both methods can be estimated quantitatively.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.4
• /
• pp.136-142
• /
• 2009

The vehicle's light-weight technology is divided into optimization of structure geometric and material. Structure geometric optimization and improvement of materials has examined to be power-train and maintenance on the severe condition. The core technology of Special vehicle's light-weight is constitute by Drop box, Axle and Final reduction gear. Technology and product of the parts is high to overseas and import dependency. We will want to examine the possibility of light-weight for the Axle Case and Drop box-connections. In this research, conventional design of excess weight will inhibit the mobility and fuel efficiency. Through the improvement of Axle material, we saw the possibility reducing weight. If you use the results of these studies, it will be available to domestic production technology and reducing weight of RV car, Dump truck, Track crain, etc.

• International Journal of Aeronautical and Space Sciences
• /
• v.15 no.4
• /
• pp.383-395
• /
• 2014

According to the requirement of wing weight estimation and frequent adjustments during aircraft conceptual design, a wing weight estimation method considering the constraints of structural strength and stiffness is proposed to help designers make wing weight estimations rapidly and accurately. This method implements weight predictions on the basis of structure weight optimization with stiffness constraints and strength constraints, which include achievement of wing shape parametric modeling, rapid structure layout, finite element (FE) model automated generation, load calculation, structure analysis, weight optimization, and weight computed based on modeling. A software tool is developed with this wing weight estimation method. This software can realize the whole process of wing weight estimation with the method and the workload of wing weight estimation is reduced because much of the work can be completed by the software. Finally, an example is given to illustrate that this weight estimation method is effective.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.40-42
• /
• 1998

The levitation magnets for the UTM-01(Urban Transit Maglev) take up a substential portion of the vehicle weight and vehicle cost. It is thus very important to reduce the weight of magnets by improving their performance and also reduce the cost of making them. A very extensive study was conducted to achieve above goals. Shape of the magnet core was varied and various core materials were tested. Also tested was the anodized sheet coil to replace the currently used rectangular shape Al coil. The study so far has improved the performance of the magnet substantially. The levitation force-to-magnet weight ratio has been improved from 6.8 to 9.2 as a result. This improvement reduced to magnet weight of the UTM-01 test vehicle by 900 kg.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.91-99
• /
• 2010

The center of gravity on vehicle is a fundamentally important point for assessing and measuring the characteristics of vehicle dynamics. Especially, the center of gravity height on vehicles is the closest factor with respect to rollover accidents in a social issue nowadays. In this paper, the center of gravity height in conjunction with vehicle parameters of vehicle weight, driving axle and roof height after measured by vehicle weight and loading location by means of VCGM developed by KATRI with good performance that the accuracy was less than 0.6% and repeatability 0.3% for vehicles being used in the whole world was observed. As a result of study, the location of center of gravity height on vehicle was able to be estimated with only roof height on vehicle.