• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.4
• /
• pp.39-49
• /
• 2022

In this study, data on traffic volume and weight of small trucks were collected from three National Highways to identify the overload status of small trucks excluded from domestic overloaded vehicle enforcement. These data were classified according to the vehicle type, day of the week, and time of day to analyze the overload distributions by the vehicle total weight. From the analysis results by vehicle type, on average, the overload ratios for trucks of 1.5 tons or less, 2.5 tons or less, 3.5 tons or less were 6.2%, 31.7%, and 13.7%, respectively. In addition, for the same vehicle model, there was a difference by collection point, and the smaller the total weight of the small truck, the higher the overload ratio. From the results according to the day of the week, there was no tendency for the overload ratio to appear high on a specific day, but there was a predictable occurrence pattern at each site. In addition, from the results by the time of day, the overload ratio was the highest on average after lunch (13:00-15:59) at all sites.

• International Journal of Highway Engineering
• /
• v.17 no.4
• /
• pp.1-9
• /
• 2015

PURPOSES : The purpose of this study is to revise the weight to power ratio of the representative truck in S. Korea. So far, S. Korea has been using the unit lb/hp, and the construction machines were not considered in the evaluation of the performance of trucks. METHODS : This study was performed to recommend the use of ISO system of units, and to analyze the weight to power ratios of the representative trucks in S. Korea, including the dump trucks, concrete mixer trucks, and asphalt and concrete diffusers. RESULTS: From this study, the 85 percentile value of the weight to power ratio of the trucks in S. Korea's was found to be 103.6 kg/kw. CONCLUSIONS : The performance standard for the representative truck has to be increased upward, considering the travel pattern of the dump trucks, concrete mixers, and asphalt and concrete diffuser trucks, travel distances, narrow area (work zone) of operation, and the saving in construction budget for climbing lane. Based on this study, the weight to power ratio of the representative truck in S. Korea could possibly be revised to 100~110 kg/kW.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.3
• /
• pp.56-66
• /
• 2013

Weight reduction of the VTHL / TSTO type of the reusable launch vehicles using RBCC engines are investigated. To predict weight and thrust of the vehicles, equations of motion are analyzed. Analysis results are compared with specifications of existing launch vehicles for validations. For the mission of inserting 2.5 ton payload to 200 km circular orbit, the case A, which uses the RBCC engine in the 1st stage shows smaller weight than the case B, which uses the RBCC engine in the 2nd stage. The weight of the case A shows only 25.8% of a existing rocket launch vehicle's weight.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.spc3
• /
• pp.262-268
• /
• 2012

In the recent research technical solutions have been studied to integrate renewable energy into unmanned aerial vehicles to use it as the main power source. As the weight of the aerial vehicle body is essential for its performance, we consider to use light-weight solar cell technology. Furthermore fuel cells are also integrated create a highly energy-efficient aerial robot. In this paper, construction concept and software design of the tilt-rotor aerial vehicle GAORI is introduced which uses solar cells and fuel cells as power source. The future work direction and prognosis are discussed.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.7-12
• /
• 2008

A hot stamping technology of vehicle door impact beam made of thin sheet steel has been developed, with the aim of ensuring occupant safety in a side collision. This technology has been implemented to increase the strength of vehicle body parts and to reduce not only the weight of door impact beam but also the number of work processes. Mechanical tests were performed to obtain material properties of hot-stamped specimen and those were used as input data in stamping and structural simulation for optimal design of door impact beam. Strength of hot-stamped door impact beam increased to the value 102% higher than that of conventional pipe-shaped door impact beam and structural simulation showed that hot-stamped door impact beam achieved 28% weight reduction.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.129-134
• /
• 2001

One of the most important purposes in the design of machines and structures is to produce the most light products of the lowest price with satisfying function and performance. In this study, a scheme of design optimization for the weight down of vehicle body structure is presented. Design sensitivity of vehicle body structure is investigated and design optimization is performed to get weight down with the allowable stiffness of body in white. Stress, deformation and natural frequencies are the constraint of the optimization.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.28 no.1
• /
• pp.83-89
• /
• 2020

Personal air vehicle (PAV) is considered by aviation engineers as a solution to provide fast urban mobility. The purpose of designing a optionally piloted PAV (OPPAV) is to provide an individual air vehicle. The airframe structure is designed with high strength carbon fiber composite to reduce the aircraft weight. This paper presents an overview of sizing process for OPPAV at the conceptual design level. It consists of load analysis, structural sizing and development of efficient design allowable values for composite material. The weight is estimated based on sizing process, including strength and stiffness requirements. The objective of this study is to present a overview of structural sizing procedure and fast tool for preliminary design phases.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.92-99
• /
• 2006

Design capability for high safety vehicle with light weight is crucial to enhancing competitive power in vehicle market. The structural foam can contribute to restraining section distortion in body members undergoing bending collapse at vehicle crash. In this study, first, the validation of analysis model including structural foam model for simulating fracture behavior was discussed, and the bending collapse characteristics of five representative section types were analyzed and compared. Next, with changing the laminate foam shape, load carrying capability and absorbed energy were observed. The results suggests a design strategy of body members filled with laminate foam, leading to effectively elevating bending collapse characteristics with weight increase in the minimum.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.5
• /
• pp.85-93
• /
• 2004

Electric vehicle body has to be subjected to uniform load and requires auxiliary equipment such as air pipe and electric wire pipe. Especially, the cross beam supports the weight of passenger and electrical equipments. This need to use adaptive design in initial design stage to gain economy through interchangeability between many kinds of components. This study performs the topology optimization by the concept of homogenization based on optimality criteria method which is efficient for the problem with a number of boundary condition and design variable. Therefore this provides the method to determine the optimum position and the shape of circular hole in the cross beam and then can achieve the weight minimization of electric vehicle body.

• Structural Engineering and Mechanics
• /
• v.85 no.5
• /
• pp.645-654
• /
• 2023

Based on first-order shear deformation theory, a wave propagation model of graphene platelets reinforced metal foams (GPLRMFs) circular plates is built in this paper. The expressions of phase-/group- velocities and wave number are obtained by using Laplace integral transformation and Hankel integral transformation. The effects of GPLs pattern, foams distribution, GPLs weight fraction and foam coefficient on the phase and group velocity of GPLRMFs circular plates are discussed in detail. It can be inferred that GPLs distribution have great impacts on the wave propagation problems, and Porosity-I type distribution has the largest phase velocity and group velocity, followed by Porosity-III, and finally Porosity-II; With the increase of the GPLs weight fraction, the phase- and group- velocities for the GPLRMFs circular plate will be increased; With the increase of the foam coefficient, the phase- and group- velocities for the GPLRMFs circular plate will be decreased.