• 한국정밀공학회지
• /
• 제30권2호
• /
• pp.231-235
• /
• 2013

The purpose of this paper is to compare with estimation of equivalent fatigue load in time domain and frequency domain and estimate the fatigue life of structure with multi-axial vibration loading. The fatigue analysis with two methods is implemented with various signals like random, sinusoidal signals. Also an equivalent fatigue life estimated by rainflow cycle counting in time domain is compared with results estimated with probability density function of each signal in frequency domain. In case of frequency domain, equivalent fatigue life can estimate through Dirlik's method with probability density function. And the work proposed in this paper compared the fatigue damage accumulated under uni-axial loading to that induced by multi-axial loading. The comparison is preformed for a simple cantilever beam, which is exposed to vibrations of several directions. For verification of estimation performance of fatigue life, results are compared to those of FEM analysis (ANSYS).

• 한국환경과학회지
• /
• 제17권4호
• /
• pp.397-403
• /
• 2008

The purpose of this study is to investigate weighted compaction density according to a leading density in truck, a compaction density of solid waste and composition ratios of solid waste fur calculation of a capacity of the landfill sites. The experiments for calculations of in-place density at landfill site have been conducted in S landfill site at B City. The size of vessel for measuring the compaction density was $1m^3(1m{\times}1m{\times}1m)$. The experiment tests have been carried out methods (1 time for bulldozer and 4 times for compactor) that do contain all of specification at the landfill site. Average of the loading density at the landfill site was $0.264\;ton/m^3$ ($0.113{\sim}0.487\;ton/m^3$). When the loading density for each compositions was compared, the composition of the highest average loading density ($0.474\;ton/m^3$) was miscellaneous wastes. The composition of the lowest average loading density ($0.120 ton/m^3$) was general solid waste. The reported results indicated that the compaction density at the landfill site was $0.538\;ton/m^3$, which was calculated with weighted incoming ratios of compositions. The ranges of the density for each composition were from $0.021\;ton/m^3$ to $0.221\;ton/m^3$. When the compaction density for each composition was compared, the composition with the highest average compaction density ($0.221\;ton/m^3$) was miscellaneous wastes. The composition with the lowest average compaction density ($0.021\;ton/m^3$) was general solid wastes.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.303-303
• /
• 2000

It is difficult to determine the static axle weight of a vehicle with weigh-in-motion systems which in absence measure instantaneous axle impact forces. The difficulty in determining a static axle weight results from dynamic effects induced by vehicle/road interactions. One method to improve the problem is to quantify a statistical confidence level for measured axle weight. The quarter-car model is used to simulate vehicle motion, Also, the road input to vehicle model can be characterized in statistical terms by PSD (power spectral density) of appropriate amplitude and frequency contents other than an exact spatial distribution. The confidence levels for the measured axle weight can be obtained by the random process analysis using both vehicle model and road input.

• 한국항공우주학회지
• /
• 제31권8호
• /
• pp.91-98
• /
• 2003

발사체의 구조해석적인 측면에서 외부하중에 따른 발사체의 반응을 파악하는 것은 중요한 일이다. 기본적으로 발사체는 응력집중이나 내부 모듈간의 변위 간섭 등이 일어나지 않게 설계되어야한다. 이를 위해서는 외부하중에 관한 연구가 선행되어야 한다. 발사체에 작용하는 외부하중 중 연소 및 배기에 의해 발생하는 음향하중은 통계적 방법으로 다루어야 하는 랜덤 하중이다. 본 연구에서는 발사시 작용하는 음향하중에 대하여 하중 함수를 구성하고, 이를 이용하여 발사체의 하중해석을 수행하였다. 음원 할당 방법으로 음향하중을 추정하여 하중함수를 구성하였고, 이를 발사체의 유한요소 모델에 적용하였다. 응력해석을 이용하여 발사체의 구조 강성을 확인할 수 있었으며, 발사체 각 섹션의 경계면에서의 가속도 파워 스펙트럴 밀도함수를 구할 수 있었다. 이러한 결과를 이용하여 각 섹션의 진동 시험에 필요한 스펙을 도출할 수 있다.

• Journal of Biosystems Engineering
• /
• 제33권1호
• /
• pp.38-44
• /
• 2008

The freight vehicle is mostly used to transport the fruit. Shock and impact generated by the freight vehicle may give serious damage to fruits hence to reduce the fruits damage, the optimum packaging design during transportation by vehicle is required. In order to design the packaging system for fruit transportation optimally, the comprehension of characteristic for vibration and shock acting on vehicles under various road conditions and loading methods is required. This research was performed to analyze the shock characteristics, acceleration level and power spectral density (PSD) of the fruit transportation vehicles under several travel roads and positions. The vibration signal was measured and analyzed at the transportation vehicle operating on the road of three different surface conditions. The maximum acceleration was measured at the rear-end of the vehicle, and the acceleration in the direction of up-and-down (z-axis) was much greater than those in the directions of back-and-forth (x-axis) or right-and-left (y-axis). The peak acceleration in the direction of up-and-down (z-axis) at the vehicle driving on the expressway, the local road paved with concrete, and unpaved local road were 5.3621 G, 8.232 G, and 14.162 G respectively. PSD at 2.44 Hz showed maximum value at all road conditions. The maximum values of PSD on the expressway, a local road paved with concrete, and unpaved local road were 0.0075222 $G^2/Hz$, 0.058655 $G^2/Hz$, and 0.24598 $G^2/Hz$ respectively. The value of PSD decreased with an increase of the vibration frequency of the transportation vehicle. In most cases, the vibration frequency was below 20 Hz during transportation.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.315-325
• /
• 2018

This paper investigates optimum air-gap flux distribution with third harmonic rotor flux orientation adjustment for five-phase induction motor. The technique of objective is to generate a nearly rectangular air-gap flux, and it improves iron utilization under variation loading conditions. The proportional relations between third harmonic and fundamental plane currents is usually adopted in the conventional method. However, misalignment between fundamental and third harmonic component occurs with variation loading. The iron of stator teeth is saturated due to this misalignment. This problem is solved by third harmonic rotor flux orientation adjustment simultaneously, and direction and amplitude are changed with mechanical load variation. The proposed method ensures that the air-gap flux density is near rectangular for a maximum value from no load to rated load. It is confirmed that the proposed method guarantees complete both planes decoupling with third harmonic flux orientation adjustment. The effectiveness of the proposed technique is validated experimentally.

• International Journal of Railway
• /
• 제5권2호
• /
• pp.71-76
• /
• 2012

Recently, axle load, operating speed and traffic density on railroads have had a tendency to increase and thereby cause additional pressure applied on used track. These operating conditions frequently result in service failure due to wear caused by wheel-rail contact and fatigue damage under cyclic loading. Among rail defects, the transverse crack, which has been the most dangerous type of fatigue damages, is developed from the subsurface crack near the rail running face and grows perpendicular to the rail surface. Therefore, it is necessary to investigate systematically the growth behavior of transverse crack for rail steel under mixed mode. In this study, the fatigue crack growth behavior of the transverse crack in rail steel was experimentally investigated under mixed-mode variable amplitude loadings.

• 전산구조공학
• /
• 제10권3호
• /
• pp.233-240
• /
• 1997

본 연구에서는 다양한 구조 및 하중조건에 대하여 중차량의 주행에 의한 충격효과를 분석하였다. 중차량 주행시의 다주형 강판형교의 동적해석에서는 노면조도 및 차륜-바닥판 사이의 상호작용을 고려하였다. 진입로와 교량바닥판의 노면형상은 각 노면조도에 따라 지수 스펙트럴 밀도 함수를 사용하여 생성시켰으며, 교량바닥판과 차륜사이의 상관력을 좀더 합리적으로 반영하기 위해 개선된 후처리기법을 사용하여 보정하였다. 또한 교량진입부에서 발생할 수 있는 바닥판과 진입로사이의 단차조건도 분석하였다. 현행 도로교 표준 시방서에 준하여 설계된 다양한 교량들에 대하여 동적거동에 중요한 영향을 미치는 구조인자들(경간장, 주형간격 등)의 영향을 체계적으로 검토하였다. 다양한 주행속도에 따른 단일주행에 의한 기본적인 하중상태 뿐만 아니라 동일차선 및 인접차선을 주행하는 다수 차량의 하중조건도 검토하였다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1997년도 봄 학술발표회 논문집
• /
• pp.185-191
• /
• 1997

The study presents the linear dynamic analysis of bridges under vehicular movement to examine the performance characteristics due to the various structural and loading conditions. The road surface roughness and bridge-vehicle interactions are considered. The road surface profiles for the approaching roadway and bridge decks are generated from power spectral density functions for different road roughness conditions. A new filtering method using the wheel trace is proposed to obtain the more rational bridge-vehicle interactions from the randomly generated road surface. The dynamic responses of various bridges designed according to current design practice are examined, in which important structural parameters(such as span length, girder spacing, etc.) are considering systematically. In addition, the traffic conditions of multi-truck traveling either consecutively on the same lane or side-by-side on the adjacent lanes are also evaluated.

• 한국도로학회논문집
• /
• 제8권3호
• /
• pp.29-37
• /
• 2006

본 연구는 현재 수행중인 "한국형 포장 설계법 개발과 포장성능 개선방안 연구"의 일환으로 역학-경험적 포장 설계법에 사용될 교통하중 입력변수를 정량화하기 위해서 실시하였다. 교통하중 정량화를 위하여 기존의 ESAL 개념이 아닌 축하중 스펙트럼을 이용하였다. 이를 위하여 교통량 통계 연보내 교통량 자료를 가지고 일반 국도에 대한 대표 축하중 조사지점을 차로별, 지역특성별 구분에 따라 33개 지점을 통계적 방법을 이용하여 선정하였다. 그리고 선정된 대표 지점을 대상으로 축하중 계측기를 이용하여 각 차종에 대한 축하중을 조사하였다. 측정된 축하중 자료는 각각 분류된 조건에 따라서 축하중 스펙트럼으로 표준화하였으며, 그 방법으로 누적밀도함수인 S-커브 곡선을 이용하여 각 조건별 계수를 제시하였다.