• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.60-67
• /
• 2006

To improve the vehicle fuel economy, various technologies have been studied. Meanwhile it deteriorates fuel economy that the increased driving torque for Power Steering System (PSS) due to weighted vehicle and widened tire for low speed driving and parking. So the larger driving torque for PSS is, the lower fuel economy is. Therefore, the study about the effect of the driving torque for PSS and the engine total friction must be preceded to improve the vehicle fuel economy. In this study, a PSS module separated from the vehicle is used to measure the driving torque for PSS with respect to the pressure of PSS. The result shows that the driving torque for PSS was in direct proportion to the pressure of PSS 3 (N-m) driving torque for PSS vs. 10 (bar) pressure of PSS, and 8 (N-m) vs. 40 (bar). In addition, the driving torque and pressure for PSS was measured according to the engine speed in the component test condition which was in the vehicle condition. Measuring the driving torque for PSP in the vehicle condition was established by using the VeFAS which was a fuel economy analyzer developed in our lab and installing PSS By-pass line. The effect of the driving torque for PSS on the vehicle fuel economy was analyzed with FTP-75 cold start mode.

• Proceedings of the IEEK Conference
• /
• 2001.06e
• /
• pp.127-130
• /
• 2001

In this paper, we describes a method of estimating traveling direction of a autonomous vehicle. For the development of autonomous vehicle, it is important to detect road lane and to reckon traveling direction. The object of a propose algorithm is to perform lane detection in real-time for standalone vision system. And we calculate efficent traveling direction to find steering angie for lateral control system. Therefore autonomous vehicle go forward the center of lane by adjusting the current steering angle using traveling direction.

• Journal of the Korean Society for Railway
• /
• v.5 no.1
• /
• pp.18-25
• /
• 2002

This paper is to study a comparison of ride stabilities for the guideway vehicle between its three primary steering types; the front-rear wheel steering type, tile independent wheel steering and the front wheel steering. A numerical model were built to investigate various factors to have an influence on the vehicular stability. It was shown that dynamic stabilities of the three types were dependent on the steering gain ratio of front wheel steering to rear. The front-rear wheel steering type was more stable for the value of positive steering gains and the shorter distance between front axle and guide link showed better stabilities. On the contrary, the independent wheel steering was more stable for the value of negative gains and the longer distance between front axle and guide link showed better stabilities. Ride characteristics of he front wheel steering seemed to be found midway. Ride behaviors due to time delay from front steering to rear were very different from steering type to type.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.8
• /
• pp.856-864
• /
• 2008

This paper describes a vehicle low speed driving assistant (VLDA) system that is composed of laser scanner. This vehicle is designed for following lead vehicle (LV) without driver's operation. The system is made up several component systems that are based on unmanned ground vehicle (UGV). Each component system is applied to use advanced safety vehicle developed to complete UGV system. VLDA system was divided into vehicle control system and obstacle detecting system. The obstacle detecting system calculate distance and angle of LV and transmit these data to vehicle control system using front, left and right laser scanners. Vehicle control system makes vehicle control values such as steering angle, acceleration and brake position and control vehicle's movement with steering, acceleration and brake actuators. In this research, we designed VLDA system like as low speed cruise control system and test it on real road environments.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.233-237
• /
• 2002

Vehicle Dynamics Control(VDC) has been a breakthrough and become a new terminology for the safety of a driver and improvement of vehicle handling. This paper examines the usefulness of a brake steer system (BSS), which uses differential brake forces for steering intervention in the context of VDC. In order to help the car to turn, a yaw moment can be achieved by altering the left/light and front/rear brake distribution. The steering function achieved through BSS can then be used to control lateral position in an unintended road departure system. A 8-DOF non-linear vehicle model including STI tire model will be validated using the equations of motion of the vehicle, and the non-linear vehicle dynamics. Since Fuzzy logic can consider the nonlinear effect of vehicle modeling, Fuzzy controller is designed to explore BSS feasibility, by modifying the brake distribution through the control of the yaw rate of the vehicle. The control strategies developed will be tested by simulation of a variety of situation; the possibility of VDC using BSS is verified in this paper.

• International journal of advanced smart convergence
• /
• v.11 no.2
• /
• pp.219-225
• /
• 2022

Recently, the popularization of personal mobility(PM) has made it possible to see many electric scooters. The energy source of personal transportation used by the general public and the disabled can be seen as environmentally friendly as electricity. Personal transportation means are divided into small electric vehicles because they use electric energy, and they are being treated as new models by automobile manufacturers in each country and spurring development. On the other hand, personal transportation means may cause various types of traffic accidents as they travel between roads and a human walk. In order to prevent such accidents, it is judged that the enactment of laws on the establishment of specifications for electric scooters, which are personal transportation means, and the method of restricting road operation should be given priority. The electric scooter is basically different from the conventional vehicle. The steering shaft of the steering system applied to the electric scooter one to two is possible. 1 to 2 the front-wheel under the steering column is used. It is classified according to the number of wheel installed at the electric scooter is the vehicle body into 2 wheel - electric scooter, and 3 wheel - electric scooter and 4 wheel - electric scooter. In this study, we propose a steering shaft design model that can be applied to an electric scooter, one of personal transportation means. A design model for 1-shaft steering and 2-shafts steering that can be applied to electric scooters is proposed. In addition, we have produced the prototypes for the commercialization of the proposed models, and reviewed the pros and cons of the manufactured prototypes and models.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.989-990
• /
• 2012

• Journal of the Korean Institute of Intelligent Systems
• /
• v.7 no.4
• /
• pp.29-39
• /
• 1997

A discrete model reference control scheme for a vehicle four wheel steering system(4WS) is proposed and evaluated for a class of discrete time nonlinar dynamics. The schmen employs a neural network to identify the plan systems, wher the neural network estimates the nonlinear dynamics of the plant. The algorithm is proven to be globally stable, with tracking errors converging to the neighborhood of zero. The merits of this scheme is that the global system stability is guaranteed. Whith thd resulting identification model which contains the neural networks, the parameters of controller are adjusted. The proposed scheme is applied to the vehicle active four wheel system and shows the validity and effectiveness through simulation. The three-degree-of freedom vehicle handling model is used to investigate vehicle handing performances. In simulation of the J-turn maneuver, the yaw rate overshoot reduction of a typical mid-size car is improved by 30% compared to a two wheel steering system(2WS) case, resulting that the proposed scheme gives faster yaw rate response andl smaller side slip angle than the 2WS case.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.17-23
• /
• 2012

An integrated dynamic control (IDCF) with an active front steering system and an active rear braking system is proposed and developed in this study. A fuzzy logic controller is applied to calculate the desired additional steering angle and desired slip of the rear inner wheel. To validate IDCF system, an eight degree of freedom, nonlinear vehicle model and a sliding mode wheel slip controller are also designed. Various road conditions are used to test the performance. The results show that the yaw rate of IDCF vehicle followed the reference yaw rate and reduced the body slip angle, compared with uncontrolled vehicle. Thus, the IDCF vehicle had enhanced lateral stability and controllability.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.6
• /
• pp.553-558
• /
• 2010

In this paper, we proposed a teleoperation scheme of unmanned grounded vehicle to improve telepresence. Especially, bilateral control architecture for transmitting realistic steering feeling to the remote driver is investigated. System architecture of the teleoperated remote vehicle is introduced with visual, auditory and kinesthetic haptic channel. Several bilateral control architectures are proposed for transmitting remote steering feeling, and subject tests are done to evaluate the performance. Position-force bilateral control architecture with returning torque compensation algorithm shows best performance.