• IEMEK Journal of Embedded Systems and Applications
• /
• v.17 no.5
• /
• pp.257-263
• /
• 2022

Active stabilizers use signals such as steering angle, yaw rate, and lateral acceleration to vary the roll stiffness of the front and rear suspension depending on the vehicle's driving conditions, and are attracting attention as RSC (Roll Stability Control) system that suppresses roll when turning and improves ride comfort when going straight. Various studies have been conducted in relation to active stabilizer bars and RSC systems. However, accurate modeling of passive stabilizer model and active stabilizer model and vehicle dynamics analysis result verification are insufficient, and performance result analysis related to vehicle roll angle estimation and electric motor control is insufficient. Therefore, in this study, an accurate vehicle dynamics model was constructed by measuring the passive/active stabilizer bar model and component parameters. Based on this, the analysis result with high reliability was derived by comparing the roll angle estimation algorithm based on the lateral acceleration and suspension of the vehicle with the actual vehicle driving test result. In addition, it was intended to accurately analyze the motor torque characteristics and roll reduction effects of the electric motor-driven RSC system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.22-28
• /
• 2011

This paper presents an active roll motion control of a passenger vehicle. The roll controller is designed in the framework of $H_{\infty}$ control scheme based on the 3 DOF vehicle model taking into consideration parameter variations, which affect the roll dynamics, and unmodeled high frequency dynamics for robustness and performance. In order to investigate the feasibility of the active roll control system in a car, its performance is evaluated by simulation in a full vehicle model with nonlinear tire characteristics under various operating conditions. Finally, in order to enhance the performance in a transient region taking into account the limited bandwidth of the actuating module, a hybrid control strategy is presented.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.8 s.227
• /
• pp.1125-1134
• /
• 2004

This paper presents a mathematical model which is about the dynamics of not only a two wheel steering vehicle but a four wheel steering vehicle. A sliding mode ABS control strategy and PID rear wheel control logic are developed to improve the brake and cornering performances, and enhance the stability during emergency maneuvers. The performances of the controllers are evaluated under the various driving road conditions and driving situations. The numerical study shows that the proposed full car model is sufficient to accurately predict the vehicle response. The proposed ABS controller reduces the stopping distance and increases the vehicle stability. The results also prove that the ABS controller can be employed to a four wheel steering vehicle and improves its performance. The four wheel steering vehicle with PID rear wheel controller shows increase of stability when a vehicle speed is high and sharp cornering maneuver when a vehicle speed is low compared to that of a two wheel steer vehicle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.8-15
• /
• 2013

Recently many kinds of electric vehicles have been developed as many governments demand the environmental friendly vehicles. In this paper, study of load optimization for the electric vehicle which has multiple axle power system was conducted. For the analysis of the vehicle which has three or four driving axles, a method based on the geometry and assumptions that considering axles as a spring model and normal forces of the axles are proportional to the displacement of the axles was applied with basic vehicle dynamics. With the developed vehicle analysis technique, algorithm to find the optimal motor operating points was developed. Using this algorithm, it was possible to find the optimization of vehicle load distribution for multiple axles according to the driving cycles. Also, control logic for the vehicle can be developed based on the optimization simulation results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.199-206
• /
• 2006

Real time vehicle dynamics models have been developed with the subsystem synthesis method for intelligent vehicle HILS system. Three different models for solving subsystem equations are compared in order to find out the best suitable model for HILS applications. The first model is based on the generalized coordinate partitioning technique, and the second one is on the approximate function approach, and the last one is on the constraint stabilization method. To investigate the theoretical efficiency of three proposed methods, arithmetic operators used in the formulations of three models are counted. Bump run simulations with half-sine bump have also carried out with three different models to measure the actual CPU time to validate theoretical investigation.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.2
• /
• pp.259-269
• /
• 2015

The issue of the longitudinal stability of a WIG vehicle has been a very critical design factor since the first experimental WIG vehicle has been built. A series of studies had been performed and focused on the longitudinal stability analysis. However, most studies focused on the longitudinal stability of WIG vehicle in cruise phase, and less is available on the longitudinal static stability requirement of WIG vehicle when hydrodynamics are considered: WIG vehicle usually take off from water. The present work focuses on stability requirement for longitudinal motion from taking off to landing. The model of dynamics for a WIG vehicle was developed taking into account the aerodynamic, hydrostatic and hydrodynamic forces, and then was analyzed. Following with the longitudinal static stability analysis, effect of hydrofoil was discussed. Locations of CG, aerodynamic center in pitch, aerodynamic center in height and hydrodynamic center in heave were illustrated for a stabilized WIG vehicle. The present work will further improve the longitudinal static stability theory for WIG vehicle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.5
• /
• pp.581-587
• /
• 2016

Braking is a basic and an important safety feature for all vehicles, and the final braking performance of a vehicle is determined by the vehicle's ABS performance and tire performance. However, the combination of excellent ABS and tires will not always ensure good braking performance. This is due to the fact that tire performance has non-linearity and uncertainty in predicting the repeated increase and decrease of wheel slip when activating the ABS, thus increasing the uncertainty of tire performance prediction. Furthermore, existing studies predicted braking performance after using an ABS that used a wheel slip control as a controller, which was different from an actual vehicle's ABS that controlled angular acceleration, therefore causing a decrease in the prediction accuracy of the braking performance. This paper reverse-designed the ABS that controlled angular acceleration based on the information on brake pressure, etc., which were obtained from vehicle tests, and established a braking performance prediction analysis model by combining a multi-body dynamics(MBD) vehicle model and a magic formula(MF) tire model. The established analysis model was verified after comparing it with the results of the braking tests of an actual vehicle. Using this analysis model, this study analyzed the braking effect by vehicle factor, and finally designed a tire that had optimized braking performance. As a result of this study, it was possible to design the MF tire model whose braking performance improved by 9.2 %.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.383-386
• /
• 2005

An integrated analytical model which should have essential dynamics on the longitudinal railway vehicle is developed. The model consists of translational movement, rotational movement, brake actuator, adhesion force between rail and wheel, and brake friction force between wheel and pad. Thus, during the deceleration for stopping, a feedback controller controlling the brake cylinder pressure is designed to improve ride quality and to release friction problems. Through the developed model, the feasibility of controlling the cylinder pressure is verified for the better performances during braking.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.3
• /
• pp.368-375
• /
• 2012

Durability performance evaluation of automotive components is very important and time consuming task. In this paper, to reduce vehicle component development time and cost virtual testing simulation technology is used to evaluate durability performance of a passenger car front aluminum sub-frame. Multibody dynamics based vehicle model and virtual test simulation model of a half car road simulator are validated by comparisons between rig test results and simulation results. Durability life prediction of the sub-frame is carried out using the model with road load data of proving ground which can evaluate accelerated durability life. We found that the durability performance of the sub-frame is sufficient and it can be predicted within short time compared to rig test time.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.13 no.3
• /
• pp.237-245
• /
• 2008

We developed a computational method on coupled dynamics of tracked vehicle on seafloor and long flexible pipe. The tracked vehicle is modeled as rigid-body vehicle, and the linked flexible pipe is discretized according to a lumped-parameter model. The equations of motion of the rigid-body vehicle on the soft seafloor are combined with the governing equations of flexible pipe dynamics. Four Euler parameters method is used to express the orientations of the vehicle and the flexible pipe. In order to solve the nonlinear coupled dynamics of vehicle and flexible pipe an incremental-iterative formulation is implemented. For the time-domain integration $Newmark-\beta$ method is adopted. The total Jacobean matrix has been derived based on the incremental-iterative formulation. The interactions between the dynamics of flexible pipe and the mobility of the tracked vehicle on soft seafloor are investigated through numerical simulations in time domain.