• Speech Sciences
• /
• v.4 no.1
• /
• pp.19-34
• /
• 1998

The author collected and compared midsagittal, coronal, coronal oblique, and transversal images of Korean monophthongs /a, i, e, o, u, i, v/ produced by a healthy male speaker using 1.5 T MR, VISION. Area was measured by computer software after tracing the cross-section at different points along the tract. Results showed that the width of the oral and pharyngeal cavities varied compensatorily from each other on the midsagittal dimension. Formant frequency values estimated from the area functions of the seven vowels showed a strong correlation (r=0.978) with those analyzed from the spoken vowels. Moreover, almost all of 35 students who listened to the synthesized vowels from area data perceived the synthesized vowels as equivalent to the spoken ones. Movement of constriction points of vowel /u/ with wider lip opening sounded /i/ and led to slight changes in vowel quality. Jaw and tongue movement led to major volume variation with an anatomical limitation. Each comer vowel varied systematically from a somewhat constant volume of the average area. Thus, the author proposed that any simulation studies related to vocal tract area variation should reflect its constant volume. The results may be helpful to verify exact measurement of the vocal tract area through vowel synthesis and a simulation study before having any operation of the vocal tract.

• Structural Engineering and Mechanics
• /
• v.27 no.6
• /
• pp.741-771
• /
• 2007

Tests were conducted on two partially pre-stressed concrete solid beams subjected to combined loading of bending, shear and torsion. The beams were designed using the Direct Design Method which is based on the Lower Bound Theorem of the Theory of Plasticity. Both beams were of $300{\times}300mm$ cross-section and 3.8 m length. The two main variables studied were the ratio of the maximum shear stress due to the twisting moment, to the shear stress arising from the shear force, which was varied between 0.69 and 3.04, and the ratio of the maximum twisting moment to the maximum bending moment which was varied between 0.26 and 1.19. The required reinforcement from the Direct Design Method was compared with requirements from the ACI and the BSI codes. It was found that, in the case of bending dominance, the required longitudinal reinforcements from all methods were close to each other while the BSI required much larger transverse reinforcement. In the case of torsion dominance, the BSI method required much larger longitudinal and transverse reinforcement than the both the ACI and the DDM methods. The difference in the transverse reinforcement is more pronounce. Experimental investigation showed good agreement between design and experimental failure loads of the beams designed using the Direct Design Method. Both beams failed within an acceptable range of the design loads and underwent ductile behaviour up to failure. The results indicate that the Direct Design Method can be successfully used to design partially prestressed concrete solid beams which cater for the combined effect of bending, shear and torsion loads.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2119-2123
• /
• 2007

This study deals with performance characteristics of heat pipe combined with a solid-liquid phase change material(PCM). The outer diameter of the heat pipe was 9.5 mm and the total length was 600 mm, where the evaporator, the adiabatic section and the condenser lengths were equally 200 mm. A paraffin wax having a melting point of 58.5$^{\circ}C$ was used as PCM. The paraffin container was attached to the adiabatic section of the heat pipe. The paraffin container had outer diameter of 18 mm, wall thickness of 1.2 mm and the total length of 100 mm. The heat pipe was tested with tilt angle of horizontal degree and favorite angle 10 degree, with evaporator lower position to provide stable operation of the heat pipe. Input thermal load was varied from 40 W, with increment of 40 W, to above 100 W until the maximum temperature of the heat pipe wall reached 200$^{\circ}C$. Test results of the PCM heat pipe were presented in comparison with conventional heat pipe of the same basic dimensions. The performance was analyzed in terms of temperature distribution, thermal resistance and heat transport capability.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.3
• /
• pp.223-233
• /
• 2012

This paper deals with free vibrations of the tapered Timoshenko beam with constant volume, in which both the rotatory inertia and shear deformation are included. The cross section of the tapered beam is chosen as the regular polygon cross section whose depth is varied with the parabolic function. The ordinary differential equations governing free vibrations of such beam are derived based on the Timoshenko beam theory by decomposing the displacements. Governing equations are solved for determining the natural frequencies corresponding with their mode shapes. In the numerical examples, three end constraints of the hinged-hinged, hinged-clamped and clamped-clamped ends are considered. The effects of various beam parameters on natural frequencies are extensively discussed. The mode shapes of both the deflections and stress resultants are presented, in which the composing rates due to bending rotation and shear deformation are determined.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.2
• /
• pp.100-104
• /
• 2000

Diamond film was deposited on Si substrate by using microwave plasma-enhanced chemical vapor deposition (MPECVD) system. After thinning the cross section between diamond film and Si substrate by ion milling method, we investigated its interface via transmission electron microscopy We could observe that the diamond film was grown either directly on Si substrate or via the interlayer between diamond film and Si substrate. Thickness of the interlayer was varied along the cross section. The interlayer might mainly composed of Sic andlor amorphous carbon. We could observe the well-developed electron diffraction pattern of both Si and diamond around the interface. Based on this result, we can conjecture the initial growth behavior of diamond film on Si substrate.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.1
• /
• pp.69-76
• /
• 2014

Survivability assessments and vulnerability reductions are required in warship design. A warship's survivability is assessed by its susceptibility, vulnerability, and recoverability. In this paper, an integrated survivability assessment for a warship subjected to multiple hits is introduced. The methodology aims at integrating a survivability assessment into an early stage of warship design. The hull surface is idealized using typical geometries for RCS (Radar Cross Section) detection probability and susceptibility. The Vulnerability is evaluated by using the shot-line. The recoverability is estimated using a survival time analysis. This enables the variation of survivability to be assessed. Several parameters may be varied to determine their effects on the survivability. The susceptibility is assessed by the probability of detecting the radar cross section of the subject and the probability of being hit based on a probability density function. The vulnerability is assessed by the kill probability based on the vulnerable area of critical components, according to the component's layout and redundancy. Recoverability is assessed by the recovery time for damaged critical components.

• Preventive Nutrition and Food Science
• /
• v.15 no.1
• /
• pp.36-43
• /
• 2010

The purpose of this study was to investigate the phenolic acid, proanthocyanidin (PAs), and flavonol glycoside contents, as well as the antioxidant activities of pine needle extracts from six species of young pine trees. The extracts were prepared from Section Pinus (Diploxylon): P. densiflora, P. sylvestris, P. pinaster and P. pinea, and Section Strobus (Haploxylon): P. koraiensis and P. strobus. Phenolics were extracted from pine needles with 80% acetone to obtain the soluble free fraction, and insoluble residues were digested with 4 M NaOH to obtain bound ethyl acetate and bound water fractions. Phenolics were analyzed by HPLC, and the hydrophilic antioxidant activity was measured using oxygen radical absorbance capacity (ORAC). Total phenolic and flavonoid contents of the soluble free fraction were higher than those of the bound ethyl acetate and bound water fractions. The main phenolics were monomers and polymers of PAs in the soluble free fraction, and phenolic acids and flavonol glycosides in bound ethyl acetate fraction. Flavonol glycosides found in different species of pine needles were qualitatively similar within fractions, but composition varied among Pinus sections. High levels of kaempferol arabinoside and an unknown compound were present in all Strobus species. The soluble free fraction had the highest antioxidant activity, followed by bound ethyl acetate and bound water fractions.

• Steel and Composite Structures
• /
• v.2 no.3
• /
• pp.171-194
• /
• 2002

In this paper, the behaviour of axially loaded partially encased composite columns made with light welded H steel shapes is examined using ABAQUS finite element modelling. The results of the numerical simulations are compared to the response observed in previous experimental studies on that column system. The steel shape of the specimens has transverse links attached to the flanges to improve its local buckling capacity and concrete is poured between the flanges only. The test specimens included 14 stubcolumns with a square cross section ranging from 300 mm to 600 mm in depth. The transverse link spacing varied from 0.5 to 1 times the depth and the width-to-thickness ratio of the flanges ranged from 23 to 35. The numerical model accounted for nonlinear stress-strain behaviour of materials, residual stresses in the steel shape, initial local imperfections of the flanges, and allowed for large rotations in the solution. A Riks displacement controlled strategy was used to carry out the analysis. Plastic analyses on the composite models reproduced accurately the capacity of the specimens, the failure mode, the axial strain at peak load, the transverse stresses in the web, and the axial stresses in the transverse links. The influence of applying a typical construction loading sequence could also be reproduced numerically. A design equation is proposed to determine the axial capacity of this type of column.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.5
• /
• pp.1725-1734
• /
• 1996

Experimental condensation and evaporation heat transfer coefficients were measured in a horizontal smooth tube and a horizontal micro-finned tube with HFC-134a. The test sections are straight, horizontal tubes with have a 9.52mm outside diameter and about 5000mm long. The micro-finned tube had 60 fins with a height of 0.12mm and a spiral angle of 25.deg.. The condensation test section was a double-pipe type with counter flow configuration. The evaporation test section employed an electic heating method. Enhancement factors which is defined as a ratio of the heat transfer coefficient for micro-finned tube to that for smooth tube, varied from 1.3 to 1.6(mass flux:110~190kg/m$^{2}$s) for condensation and 1.2 to 1.5 (mass flux:70~160kg/m$^{2}$s) for evaporation. The experimental data of condensation and evaporation heat transfer coefficients were compared to several empirical correlations. Based on these comparisons, modified correlations of the condensation and evaporation heat transfer coefficient for both smooth and micro-finned tubes were proposed.

• Journal of Korean Society for Geospatial Information Science
• /
• v.4 no.1 s.6
• /
• pp.83-91
• /
• 1996

With the growth of cities, there is a nero today for construction of outer road of cities but there are many problems in executing the scheme. In this study 5 kilos' distance, a part of the first section from East Kwangju I.C. in 36kilos' distance, the road circling Other Kwangju city is determined as the object of this study and illustrated by GIS. Besides that, the landscape which is varied according to survey location is illustrated each section by using data such as plans and 1he planed height. and the area for this study which is circling around Mt. Mudeung, a noted in Kwangju city is represented by GIS.