• 한국추진공학회지
• /
• 제17권5호
• /
• pp.1-9
• /
• 2013

노즐 목 및 출구 면적이 동시에 조절되는 축소-확대 형상의 가변노즐을 수치해석적으로 연구하였다. 최적 팽창 및 후기 연소기 구동시의 최적 노즐 형상 구현을 위해 가변 노즐이 요구된다. 후기연소기 작동유무와 노즐 플랩 위치에 따른 각 조건에 대한 정상상태 계산 및 이동격자 기법을 적용한 과도해석을 수행하였다. 노즐 가변에 의해 내부 유동장의 변화가 유발되었고, 추력이 주기적으로 변화하였다. 탈설계점에서 과대팽창으로 인해 노즐 출구 끝단에서 유동 박리 현상이 발생하였으며, 과소팽창에 의해 충격파가 발생하였다. 이러한 현상은 가변 노즐의 제어를 통해 해결할 수 있다.

• 대한기계학회논문집A
• /
• 제26권3호
• /
• pp.415-427
• /
• 2002

A clip-on type displacement gage was designed and manufactured to use for fatigue crack growth tests of M(T)(Middle-Tension) specimens. The displacement gage has good response for the deformation of the specimen and has been successfully used not only for constant amplitude loading tests but also far variable amplitude loading tests like as single peak overloading and random loading tests. All the materials for the gage can be obtained easily in domestic market, and the manufacturing cost is very low. It is expected that the designing procedure presented in this study can be applied usefully for designing other displacement gages.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.368-371
• /
• 2008

An extensometer system to measure strain and displacement of cylindrical fatigue specimen in a autoclave of high temperature and high pressure environment has been developed by KEPRI. The extensometer reads the displacement caused by fatigue loads at the target length of the specimen installed inside the autoclave. The performance of the extensometer were tested at 15MPa, $315^{\circ}C$ of a operating pressurized water reactor. Two LVDT's of magnet type were connected to the extensometer and used for converting the fatigue displacement to electronic signal. The device is being used for developing environmental fatigue curve of CF8M cast austenitic stainless steel (CASS) in the test condition of low cycle and low strain. This paper introduces the background and results of the development.

• Wind and Structures
• /
• 제20권2호
• /
• pp.315-326
• /
• 2015

To overcome the drawbacks of the traditional contact-type sensor for structural displacement measurement, the vision-based technology with the aid of the digital image processing algorithm has received increasing concerns from the community of structural health monitoring (SHM). The advanced vision-based system has been widely used to measure the structural displacement of civil engineering structures due to its overwhelming merits of non-contact, long-distance, and high-resolution. However, seldom currently-available vision-based systems are capable of realizing the synchronous structural displacement measurement for multiple points on the investigated structure. In this paper, the method for vision-based multi-point structural displacement measurement is presented. A series of moving loading experiments on a scale arch bridge model are carried out to validate the accuracy and reliability of the vision-based system for multi-point structural displacement measurement. The structural displacements of five points on the bridge deck are measured by the vision-based system and compared with those obtained by the linear variable differential transformer (LVDT). The comparative study demonstrates that the vision-based system is deemed to be an effective and reliable means for multi-point structural displacement measurement.

• 한국구조물진단유지관리공학회 논문집
• /
• 제9권3호
• /
• pp.213-220
• /
• 2005

최근 전단벽의 변형성능을 증명하기 위한 관심이 성능 설계법을 위한 적당한 자료들을 얻기 위해서 증대되고 있다. 본 연구에서는 전단벽의 변형 성능을 평가할수 있는 방법을 제시하고자 한다. 전단벽의 변위는 전단과 휨 변형의 조합된 형태로 표현될 수 있다. 수정 변환각 트러스 모델과 휨이론을 이용하여 전단과 휨변형을 산정하였으며, 또한 축력과 많은 수직 및 수평보강근의 영향을 고려할 수 있는 트러스 모델을 구축하였다. 본 연구에서 제안한 방법의 정확성을 평가하기 위하여 기 수행된 7개의 실험결과를 해석하고 실험결과와 해석결과를 비교하였다. 비교결과, 본 연구에서 제안한 방법을 사용함으로써 전단벽의 변형성능을 적절히 예측할 수 있는 것으로 나타났다. 그러나 플랜지벽이 있는 경우에는 강도와 강성의 측면에서 플랜지벽의 영향을 과대평가하며 변위성능의 측면에서는 과소평가하는 것으로 나타났다.

• 한국정밀공학회지
• /
• 제23권5호
• /
• pp.137-142
• /
• 2006

The muffler which reduce the exhaust noise and vibration from engine influence on the engine performance. Recently, exhaust variable valve has set up in the muffler controls the backpressure in the exhaust system. And the backpressure variation according to the exhaust variable valve opening has developed the engine performance. First, the preceding of structural analysis is needed and simulation experiment is requested for the study on the design factor to influence on the operation of the exhaust variable valve. In this study, setting up the various variables according to each composition element needed for the structural analysis of the exhaust variable valve, it is experimented the analysis on the influence of each design factor with the calculation of stress distribution and the displacement to cause about the backpressure for the valve through parameter study.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.167-173
• /
• 2003

For the measurement of mass flow rate at a wide range of operation conditions, it is required that the critical nozzle gas different diameters, since the mass flow rate through the critical nozzle depends on the nozzle supply conditions and the nozzle throat diameter. In the present study, both computational and experimental investigations are performed to explore the variable critical nozzle. Computational work using the 2-dimensional, axisymmetric, compressible Navier-Stokes equations are carried out to simulate the gas flow through variable critical nozzle. In experimnet, a cylinder with several different diameters is inserted into the critical nozzle to vary the nozzle throat diameter. Computational results are compared with the experimented ones. The computed results are in close agreement with experiment. It is found that the displacement and momentum thickness of variable critical nozzle are given as a function of Reynolds numbers. The discharge coefficient of the variable critical nozzle is predicted using an empirical equation.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1075-1080
• /
• 2007

In order to reduce energy consumption, secondary controlled system has been applied to many types of equipments. In lifting equipments or press machines using hydraulic cylinder, a hydraulic transformer is used as a control component instead of a valve for motion control and a component for recovering potential energy of load. The transformer is a combination of a variable displacement pump/motor as a secondary controlled element and a fixed displacement pump/motor. In this paper the effect of transformer is studied. Multiple closed loop controllers with displacement feedback of variable pump/motor, speed feedback and position feedback of cylinder are used. The efficiency and energy consumption when cylinder is driven up and down is calculated by simulation. Simulation results show that considerable energy saving is achieved by choosing load ratio, circuit type and supply pressure.

• Structural Engineering and Mechanics
• /
• 제76권4호
• /
• pp.435-449
• /
• 2020

This work presents the formulation of the isogeometric collocation method to solve the strong form equation of a unified and integrated approach of Reissner Mindlin plate theory (UI-RM). In this plate theory model, the total displacement is expressed in terms of bending and shear displacements. Rotations, curvatures, and shear strains are represented as the first, the second, and the third derivatives of the bending displacement, respectively. The proposed formulation is free from shear locking in the Kirchhoff limit and is equally applicable to thin and thick plates. The displacement field is approximated using the B-splines functions, and the strong form equation of the fourth-order is solved using the collocation approach. The convergence properties and accuracy are demonstrated with square plate problems of thin and thick plates with different boundary conditions. Two approaches are used for convergence tests, e.g., increasing the polynomial degree (NELT = 1×1 with p = 4, 5, 6, 7) and increasing the number of element (NELT = 1×1, 2×2, 3×3, 4×4 with p = 4) with the number of control variable (NCV) is used as a comparable equivalent variable. Compared with DKMQ element of a 64×64 mesh as the reference for all L/h, the problem analysis with isogeometric collocation on UI-RM plate theory exhibits satisfying results.

• Structural Engineering and Mechanics
• /
• 제90권6호
• /
• pp.601-610
• /
• 2024

Free vibration of layered conical shell frusta of thickness filled with fluid is investigated. The shell is made up of isotropic or specially orthotropic materials. Three types of thickness variations are considered, namely linear, exponential and sinusoidal along the radial direction of the conical shell structure. The equations of motion of the conical shell frusta are formulated using Love's first approximation theory along with the fluid interaction. Velocity potential and Bernoulli's equations have been applied for the expression of the pressure of the fluid. The fluid is assumed to be incompressible, inviscid and quiescent. The governing equations are modified by applying the separable form to the displacement functions and then it is obtained a system of coupled differential equations in terms of displacement functions. The displacement functions are approximated by cubic and quintics splines along with the boundary conditions to get generalized eigenvalue problem. The generalized eigenvalue problem is solved numerically for frequency parameters and then associated eigenvectors are calculated which are spline coefficients. The vibration of the shells with the effect of fluid is analyzed for finding the frequency parameters against the cone angle, length ratio, relative layer thickness, number of layers, stacking sequence, boundary conditions, linear, exponential and sinusoidal thickness variations and then results are presented in terms of tables and graphs.