• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제44회 KOSCO SYMPOSIUM 초록집
• /
• pp.7-8
• /
• 2012

The effects of interaction between partially premixed and premixed swirl flames on CO and NOx emissions were experimentally investigated using a hybrid/dual swirl jet combustor for a micro-gas turbine. Under the condition of constant angle ($45^{\circ}$) for outer swirl vane, the angle and direction of inner swirl vane installed for a partially premixed flame were varied as main parameters with a constant fuel flow rate for each nozzle. It was found that for all conditions, CO and NOx emissions were measured below 4 ppm and 15 ppm at 15% $O_2$, respectively, in a wide range of equivalence ratio (0.6~0.9). For co-swirl flows, CO emission increased dramatically as the angle of inner swirl vane increased from $15^{\circ}$ to $45^{\circ}$ near lean-flammability limit (i.e. equivalence ratio of 0.5). On the other hand, the case of swirl $angle=45^{\circ}$ provided the lowest NOx emission at higher equivalence ratios than 0.6. For counter-swirl flows, the case of swirl $angle=45^{\circ}$ extended the lean-flammability limit but higher NOx emissions were found compared to those of co-swirl flows. These results could be inferred by interaction between (inner) partially premixed and (outer) premixed swirl flames. However, these estimations were not clear yet because there was insufficient data on turbulent flow structure and fuel-air mixing in the present experimental approach.

• 대한토목학회논문집
• /
• 제38권1호
• /
• pp.63-71
• /
• 2018

본 연구에서는 베인에 작용하는 수평응력과 토크를 측정한 다음 이를 이용하여 모래의 마찰각을 구하는 연구를 수행하였다. 건조한 낙동강모래를 원통형 셀에 느슨하거나 조밀한 상태로 성형한 다음 상부에서 공기압 실린더로 상재하중(overburden pressure)을 25, 50, 75 또는 100kPa 가하여 베인(직경 5cm, 높이 10cm) 회전 시 주변에 작용하는 수평응력과 토크를 실시간으로 측정하였다. 베인 회전에 따른 최대 토크값은 느슨한 모래는 3.5~9.5Nm, 조밀한 모래는 7.4-17.6Nm 사이로 상재하중이 증가할수록 최대 토크값도 증가하였다. 조밀한 정도에 관계없이 $14-20^{\circ}$ 회전 시 최대 토크값에 도달하였으며, 베인날과 토압계의 초기 위치에 따른 최대값의 차이는 나지 않았다. 상재하중에 따라 베인에 작용하는 초기 수평응력비($K_0$)는 평균 0.33-0.35 사이이며, 베인 회전에 따라 수평응력이 전반적으로 증가하다가 모래 입자가 교란되면서 다시 감소하는 경향을 보였다. 실시간으로 측정된 수평응력과 토크를 이용하여 계산된 마찰각은 상재하중이 증가함에 따라 감소하는 경향을 보였으며, 느슨한 모래는 직접전단시험 결과와 유사한 마찰각을 보였다. 하지만, 조밀한 모래의 마찰각은 다소 과대평가하는 경향을 보였다.

• 대한기계학회논문집B
• /
• 제36권4호
• /
• pp.397-404
• /
• 2012

디젤엔진 SCR 시스템 내에서 $NO_x$를 저감을 위한 베인 타입 스태틱 믹서의 혼합유동특성을 수치적으로 연구하였다. 믹서는 원형관의 입구로부터 유동방향으로 직경의 57배 떨어진 구간에 설치하였다. 베인이 유동 축과 이루는 각과 베인의 크기 그리고 위치의 변화에 따른 유동 및 혼합특성을 고찰하였다. 원형관내에서 믹서를 통과하는 유동의 특성은 UI, 선회비, 그리고 압력계수와 같은 특성화된 성능지수로 나타내었다. 해석결과 성능지수들은 베인 각과 차단비, 베인 위치와 같은 기하학적 변수에 영향을 받음을 확인하였다. 특히, 베인 각, 베인 크기가 커지거나 원형관내의 벽면에 가까이 설치될수록 선회비는 증가하는 것을 확인하였다.

• 대한기계학회논문집B
• /
• 제33권8호
• /
• pp.580-588
• /
• 2009

This paper summarizes the experimentally-measured performance of small-scale, vertical-axis wind turbine for the purpose of improving the aerodynamic efficiency and its controllability. The turbine is designed to have a Savonius-Type rotor with an inlet guide-vane and an side guide-vane so that it achieves a higher efficiency than any lift- or drag-based turbines. The main design factors for this high-efficient, vertical wind turbine are the number of blades (Z), and the aspect ratio of Height/Diameter (H/D) among many. The basic model has the diameter of 580mm, the height of 464mm, and the blade number of 10. The maximum power coefficient of 0.50 was experimentally measured for the above-mentioned specifications. The inlet-guide vane ensures the maximum efficiency when the angle of attack to the rotor blade lies between $15^{\circ}$ and $20^{\circ}$. This experimental results for the vertical-axis wind turbine can be applied to the preliminary design of turbine output curve based on the wind characteristics at the proposed site by controlling its aerodynamic performance given as a priori.

• 대한기계학회논문집B
• /
• 제27권3호
• /
• pp.311-318
• /
• 2003

The present work evaluates the effects of mixing vane shape on the flow structure and heat transfer downstream of mixing vane in a subchannel of fuel assembly. by obtaining velocity and pressure fields. turbulent intensity. flow-mixing factors. heat transfer coefficient and friction factor using three-dimensional RANS analysis. Four different shapes of mixing vane. which were designed by the authors were tested to evaluate the performances in enhancing the heat transfer. Standard k-$\varepsilon$ model is used as a turbulence closure model. and. periodic and symmetry conditions are set as boundary conditions. The flow blockage ratio is kept constant. but the twist angle of mixing vane is changed. The results with three turbulence models were compared with experimental data.

• 설비공학논문집
• /
• 제12권2호
• /
• pp.120-130
• /
• 2000

A flow uniformity in a duct cooler of duct system of FGD(Flue Gas Desulfurization) linking a reheater and a absorber has been investigated in the present study. For this purpose, the flow characteristics according to the geometry of a vertical and horizontal vane in a curved duct of the duct system has been examined with the aid of a numerical simulation. The results indicate that the vertical vane with a little deflection toward a recirculation region makes the flow distribution in the duct cooler more uniform than that without deflection, and horizontal vane does not effect the change of the flow distribution for an angle of inclination. The mean flow uniform factor shows its maximum for duct system without the vane(case NP) and its minimum for the vertical vane with a little deflection(case P-0.8-0) .

• 플랜트 저널
• /
• 제6권2호
• /
• pp.62-69
• /
• 2010

The stability of coal pulverizer in the 800 MW coal-fired plants is vital to maintain their performance. Thus, this study analyzed the uneven abrasion of the deflector and coal spillage due to the air velocity maldistribution in the vane wheel of a bowl-type pulverizer as it is a possible cause for problems of facility using pulverized coal. In addition, air flow in the underbowl of a bowl-type pulverizer was studied to check air velocity maldistribution in the vane wheel using numerical method. In an attempt to correct the maldistribution of air velocity, air flow of the modified duct vane was studied as enlarging the length of the duct vanes installed at the air inlet duct of the pulverizer and increasing the angle of inclination. It was found that modified duct vane make the velocity distribution at the vane wheel uniform. formed by the duct vanes installed at the air inlet duct of the pulverizer and swirling flow is the major factor in making the velocity distribution of vane wheel exit uniform. This can prevent the uneven abrasion of the deflector, which is one of the components inside the pulverizer and coal spillage.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1996년도 추계학술발표회 논문집
• /
• pp.171-175
• /
• 1996

thermal diode is a device which allows heat to be transferred in one direction by convection due to difference of density of fluid. Vertical plate for heat collection and radiation are of utility for design of thermal diode. It was considered the transient process of air filled thermal diode with guide vane which combined rectangular and parallelogrammic shape enclosures. Gr was kept constantly on 1.60$\times$1010 and error range was $\pm$2% during the experiment. Nu was examined when inclined angle are 15$^{\circ}$and 45$^{\circ}$and, also the experiments was carried out with and without guide vane as well. Specially, The effect of guide vane was sensitive. Developed region inclined angle, which is characteristic of system.

• 대한기계학회논문집B
• /
• 제36권7호
• /
• pp.683-687
• /
• 2012

본 연구는 CFD 해석을 이용하여 사각 천장형 루버 디퓨저의 토출각도와 토출 유량에 따른 실내 공기유동 특성에 관한 것이다. CFD 툴은 상용프로그램인 ANSYS 13.0의 CFX를 이용하였다. 연구에 사용된 디퓨저는 적은 유량에서도 충분한 도달거리를 확보할 수 있도록 모델링하였으며, 실내 크기는 $6{\times}6{\times}2.7m$로 디퓨저의 대각선 방향으로 원형 배기구를 모델링 하였다. 토출 공기의 체적유량은 5.1CMM, 7.4CMM이며, 디퓨저의 토출각도를 $30^{\circ}$에서부터 $60^{\circ}$까지 $10^{\circ}$씩 변화하여 실내의 유동특성에 대하여 고찰하였다.

• 대한기계학회논문집B
• /
• 제28권8호
• /
• pp.929-936
• /
• 2004

In the present work, shape of the mixing vane in Plus7 fuel assembly has been optimized numerically using three-dimensional Reynolds-averaged Navier-Stokes analysis of flow and heat transfer. Standard $k-{\epsilon}$ model is used as a turbulence closure. The Response surface method is employed as an optimization technique. The objective function is defined as a combination of heat transfer rate and inverse of friction loss. Bend angle and base length of mixing vane are selected as design variables. Thermal-hydraulic performances for different shapes of mixing vane have been discussed, and optimum shape has been obtained as a function of weighting factor in the objective function.