• 소성∙가공
• /
• 제16권7호
• /
• pp.549-554
• /
• 2007

The objective of this paper is to investigate into the fabrication technology of cores for the injection mould with three-dimensional conformal cooling channels to reduce the cooling time. The location of the conformal cooling channels has been determined through the injection molding analysis. The mould has been manufactured from a hybrid rapid tooling technology, which is combined a direct metal rapid tooling with a machining process. Several injection molding experiments have been performed to examine the productivity and the validity of the designed mould. From the results of the experiments, it has been shown that the proposed mould can mold a final product within a cooling time of 3 seconds and a cycle time of 21 seconds, respectively.

• 한국진공학회지
• /
• 제8권4B호
• /
• pp.548-555
• /
• 1999

The NBI (Neutral BGeam Injection) System for the Korea Superconducting Tokamak Advanced Research (KSTAR) is composed of ion sources, neutralizers, bending magnets, ion dumps, and calorimeter. The vacuum chamber, in which all of the beam line components are enclosed, is composed of differential pumping system for the effective transfer of the neutral beams. The needed pumping speeds of each of the divided vacuum chamber and the optimized gas flow rate ot the neutralizer were calculated with the help of the particle balance equations. The minimum gas flow rate to the ion sources for producing needed beam current (120kV, 65A, 78MW), the pressure distributions in the vacuum chamber for minimizing re-ionization loss, and the beam loss rate on the beam line components were used as the input in the calculation. Also the scenario for short pulse operation was determined by analysing the time dependent equations. It showed that beam extraction during less than 0.5 sec could be made only with TMP.

• 소성∙가공
• /
• 제20권3호
• /
• pp.250-256
• /
• 2011

Vacuum-assisted thermoforming is one of the critical steps for the successful application of film insert molding(FIM) to parts of complex shapes. If the thickness distribution of the formed film is non-uniform, cracking, deformation, warping, and wrinkling can easily occur at the injection molding stage. In this study, the effects of processing parameters, which include the film heating time, plug depth, plug speed and vacuum delay time, on film thickness distribution were investigated. It was found that the film thickness at the part sidewall decreases with increasing the film heating time and plug depth, but the thickness at the bottom was found to exhibit the opposite behavior. The film thickness of the sidewall was observed to increase at higher plug speed and vacuum delay time of 0 ~ 0.3sec.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.359-359
• /
• 2011

Many research applications in basic sciences and biology such as protein crystallography require hard x-rays in the range of 3-20 keV with high brightness. A medium energy storage ring as PLS-II with a beam energy of 3 GeV can meet such high photon energies. In-vacuum undulators (IVU) with a period length of 20 mm and a peak field of 0.97 T are used in the PLS-II ring to produce such X-rays in the fundamental or higher harmonics. Due to the many poles and high fields, insertion devices like wigglers and undulators have a significant impact on the stability of the electron beam with potential degradation of beam quality and life time. Therefore, nonlinear fields must be determined by measurement and evaluated as to their impact on beam stability. Specifically, transverse field roll-off can be a serious detriment to injection in top-up mode and must be corrected. We use magnetic field measurement data to evaluated beam stability by tracking particles using an explicit symplectic integrator in both, transverse and longitudinal planes.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.230.1-230.1
• /
• 2016

본 연구에서는 Host-Dopant system 기반 적색 인광 OLED의 Emitting layer(EML)에서 doping 위치에 따른 특성 변화를 분석하였다. EML은 host 물질로 60 nm 두께의 CBP를 사용하고, 적색 발광을 위해 10 %의 $Ir(btp)_2$를 CBP의 Front, Middle, Back side에 각각 20 nm씩 doping하였다. 본 구조의 적색 인광 OLED는 current density, luminance, efficiency, EL spectrum 등을 통해 전기적, 광학적 특성 변화를 확인하였다. Front, Back side에 doping으로 인한 CBP의 Energy level이 3.6 eV에서 1.9 eV로 감소하여 각각 HTL/EML, EML/HBL의 경계에 carrier direct injection이 활성화 되었고, 이로 인한 charge balance의 저하를 확인하였다. EL spectrum결과 각 소자는 CBP의 618 nm 파장 외에도, 추가적으로 TPBi의 398 nm, NPB의 456 nm의 파장을 보였다. 이를 통해 doping 위치에 따라 exciton이 형성되는 recombination zone이 이동하고 있음을 확인하였고, Front side는 6 V의 인가전압에서는 발광 파장이 398 nm에서 높은 값을 보이나 8 V, 10 V, 12 V에서 618 nm에서 높은 값을 보이는 것으로 인가전압에 의해 recombination zone이 HTL쪽으로 이동되는 것 또한 확인하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.249.1-249.1
• /
• 2015

Quantum dots (QDs) are attracting growing attention for photovoltaic device applications because of their unique electronic, optical and physical properties. Lead sulfide (PbS) QDs are one of the most widely studied materials for the devices and known to have size-tunable properties. In this context, we investigated the relationship between the size of PbS QDs and two synthesizing conditions, a concentration of ligand, oleic acid in this work, and injection temperature. The inverted colloidal quantum dot solar cells based on the heterojunction of n-type zinc oxide layer and p-type PbS QDs were also fabricated. The size of the QDs and cell properties were observed to depend on both the QD synthesizing conditions, and hence the overall efficiency of the cell could vary even though the size of QDs used was same. The QD synthesizing conditions were finally optimized for the maximum cell efficiency.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.7-13
• /
• 1999

The potential for growth and the future impact of Rapid Prototyping that it will have on the product development cycle are enormous. Since making tools, precedes making parts, Rapid Tooling becomes widely used in automobile, aerospace, electronic, and other industries. In this study, master models formed by Rapid Prototyping of Stereolithography have been applied for vacuum casting to obtain silicone patterns which have transformed into epoxy models. The epoxy models have been measured to check dimension errors, and tested their functions. These checking and measurement have provided information on plastic injection possibilities and data for die design, Temporary die making with the materials of Aluminum/Epoxy and powder injection metal (PIM) has also been discussed in terms of hardness, surface roughness, and SEM microstructures.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.266-266
• /
• 2013

We show a set-up of poly (4,4'-aminotriphenylene hexafluoroisopropylidenediphthalimide) (6F-TPA PI)/Al sample in which holes are injected by photoelectron emission process instead of direct charge carrier injection via metal electrode. In this process, an irreversible electrical phase transition of 6F-TPA PI is found in contrast to the Al/6F-TPA PI/Al structure, leading to a write-once-readmany behavior. The photoelectron spectroscopy results measured before and after the switching process revealed that the irreversible electrical phase transition of 6F-TPA PI is attributed to the chemical modification of the carbonyl group in phthalimide moiety.

• E2M - 전기 전자와 첨단 소재
• /
• 제7권1호
• /
• pp.64-72
• /
• 1994

본 고는 현재 전기적 응용을 위한 수지 절연물의 진공/가압 수지-주형처리 분야에서 가장 앞선 기술과 연구개발력을 보유하고 있는 스위스의 Ciba-Geigy사와 최신의 진공성형 시스템을 개발, 생산하고 있는 독일의 Hedrich사 및 진공주형/자동가압 성형장비를 생산하는 스위스의 Vogel사 등을 최근에 방문하여 Epoxy, Polyurethane, Polyester 및 Silicone 수지 등의 수지절연시스템을 가지고 구조적으로 기포가 없으며 전기적, 기계적, 열적특성이 매우 우수하고 매끄러운 표면이 요구되는 수지 mold제품을 생산하는데 적용되고 있는 진공 수지-주형처리기술의 현황과 아울러 경화시간을 크게 단축시켜 생산자동화가 가능한 최신의 자동가압겔화(Automatic pressure gelation)/주입몰드공정(Injection molding process)의 특징 및 기술개발현황에 대해 파악한 내용을 소개하고자 한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.244-244
• /
• 2012

Polymer memory devices have attracted considerable attention because of their advantages such as low cost potential, good scalability, flexibility, simplicity in structure, and large capacity for data storage. Metal/poly (4,4'-aminotriphenylene hexafluoroisopropylidenediphthalimide) (6F-TPA PI)/metal system has been found to show an electrical bi-stable behavior. Here, we show a novel set-up of 6F-TPA PI/Al sample in which holes are injected by photoelectron emission process instead of direct charge carrier injection via metal electrode. In this process, an irreversible electrical phase transition of 6F-TPA PI is found, leading to a write-once-read-many (WORM) behavior. The photoelectron spectroscopy results measured before and after the switching process revealed that the irreversible electrical phase transition of 6F-TPA PI is attributed to the chemical modification of the carbonyl group in phthalimide moiety.