• 펄프종이기술
• /
• 제31권2호
• /
• pp.64-69
• /
• 1999

Drainage phenomena on the conventional fourdrinier table can be divided into two distinct zones based on the drainage mechanisms involved. In the forming zone, natural drainage is the principal water removal mechanism, while in the vacuum zone vacuum dewatering displaces water in the wet sheet with air. In this study to investigate the influence of polyelectrolyte addition on natural and vacuum dewatering a vacuum drainage tester was developed and used. Addition of PAM decreased the dryness of the wet sheet after vacuum dewatering since substantial reduction in vacuum level occurred due to flocculation of fibers. Addition of PAM, however, increased the wet web dryness when the fines content of the stock is greater than 35% indicating the presence of fines reduced the air permeability of the wet web to increase its response to vacuum dewatering. On the other hand, PEI, which flocculates the fibers and fines via patch formation, showed little impact on the drainage characteristics of the stocks.

• 한국구조물진단유지관리공학회 논문집
• /
• 제8권3호
• /
• pp.197-205
• /
• 2004

연약지반 개량을 위해 진공압밀공법을 적용할 경우 발생되는 Hardening Zone의 범위와 진공압 세기의 관계를 연구하였다. 이를 위하여 단위 셀 형식의 시험기를 제작하여 국내의 대표적 준설매립공사지역인 광양, 부산, 목포에서 채취한 고함수비 상태에서의 준설점성토에 대해 각각 함수비와 콘저항치수를 측정하여 진공압의 변화에 따른 Hardening Zone의 변화를 파악하였다. 높은 진공압상태에서는 배수재의 막힘현상과 배수재 부근에서 빠르게 생성되는 Hardening Zone 등으로 인하여 배수층으로의 간극수의 흐름이 방해되어 낮은 진공압상태에서 보다 Hardening zone의 범위가 커지지는 않았다.

• 펄프종이기술
• /
• 제36권3호
• /
• pp.52-59
• /
• 2004

The greater Increase of the demand for environmental friendly materials especially for packaging industry leads to the larger interest in the reusable and recycable materials such as pulp mold. Although the pulp mold has great characteristics for packaging, some deficiency compared with other packaging material like EPS(Expandable Polystyrene) need to be overcome, for example, the relative higher cost. In this report, since the water drainage rate at the forming zone of a wet pulp mold process could have a great influence on the economical efficiency not only by increasing machine speed but also reducing the drying energy, the optimum ways for increasing drainage were investigated The mechanism of vacuum drainage In pulp mold forming was successfully evaluated by using RDA(Retention and Darinage Analyzer). Since the conditions of stock were greatly affected by the pulping time of low consistency pulper, the optimum pupling time was investigated with considerations of all stock preparation processes. The change of stock temperature and the addition of polyelectrolyte could improve the vacuum drainage rate. It was founded that the wire mesh types of mold former had a little influence on the retention because of the relatively mild vacuum drainage. However, the bigger size of dewatering hole showed better drainage rate and could reduce the plugging and con lamination of mold.

• 펄프종이기술
• /
• 제32권3호
• /
• pp.1-9
• /
• 2000

The MDDA (Modified Dynamic Drainage Analyzer) was developed to evaluate the drainage characteristics on paper machine. The initial forming vacuum velocity was decreased with the increase of stock consistency and there were no significant effects of the applied vac-uum. On the other hand the initial forming drainage velocity was rapidly decreased with the increase of stock consistency above the 0.35 bar of applied vacuum. The final drainage time and wet web permeability showed similar trends under 0.075% consistency but increased rapidly at the higher consistencies. SFR(Specific Filtration Resistance) and drainage obtained for different vacuum level applied and deposited weights measured by using MDDA showed the linear relationship.

• Geomechanics and Engineering
• /
• 제1권3호
• /
• pp.179-191
• /
• 2009

For a two-way drainage deposit under a surcharge load, it is possible to leave a layer adjacent to the bottom drainage boundary without prefabricated vertical drain (PVD) improvement and achieve approximately the same degree of consolidation as a fully penetrated case. This depth is designated as an optimum PVD installation depth. Further, for a two-way drainage deposit under vacuum pressure, if the PVDs are fully penetrated through the deposit, the vacuum pressure will leak through the bottom drainage boundary. In this case, the PVDs have to be partially penetrated, and there is an optimum installation depth. The equations for calculating these optimum installation depths are presented, and the usefulness of the equations is studied by using finite element analysis as well as laboratory model test results.

• 펄프종이기술
• /
• 제31권1호
• /
• pp.52-60
• /
• 1999

Drainage rate in wet-end, which has significant influences on the production capacity, product quality and process economics in papermaking, becomes an important factor in the modern high speed papermaking processes owing to increased level of fines contained in today's pulp materials and increased papermaking system closure. A study was carred out to investigate the influence of beating and fines content on natural and vacuum dewatering using a vacuum drainage tester. Increase in beating and accumulation of fines in the stock decreased natural dewatering, Vacuum dewatering effect, however, increased substantially as beating and fines content were increased. But this increase in vacuum dewatering decreased again when a stock is severely beaten or fines content is greater than 35%. Above this level of fines content, mobile fines migrates to the interstices of the forming web to cause sealing or plugging which restrict fluid movement through the web.

• 한국지반공학회지:지반
• /
• 제13권2호
• /
• pp.39-54
• /
• 1997

연약지반 개량공법으로 국내에서 생산된 플라스틱 보드 드레인(PBD)이 많이 사용되고 있으나 이들에 대한 물리적 성질 및 배수성능의 검증이 미약한 실정이다. 또한 PBD의 웰 레지스턴스(well resistance)에 크게 영향을 미치는 공기(기포)의 영향에 대한 인식이 부족하다고 판단된다. 따라서 본 연구에서는 대형 실험장치를 이용하여 먼저 국산 PBD를 중심으로 물리적 성질 및 배수성능 시험을 실시하여 제품의 질적 수준을 규명하고 대표적인 국외제품과 비교했다. 아울러 PBD재의 꺾임 부분에 누적된 공기(기포)가 통수능력에 지장을 초래하는 것을 재확인하였으며 현장에서 적용할 수 있는 진공펌프를 이용하여 필기(기포)를 제거시키므로써 통수능력의 회복이 가능하다는 것을 나타냈다.

• 한국지반공학회논문집
• /
• 제38권8호
• /
• pp.29-37
• /
• 2022

연직배수재로 개량된 지반의 배수거동을 해석하기 위해서는 3차원 해석이 필요한데, Macro-element법을 이용하면 2차원 평면변형 조건으로 연직배수재의 3차원 배수효과를 고려한 효과적인 해석이 가능하다. 본 연구에서는 지반개량에서 적용되는 진공압밀공법에 Macro-element법을 적용하여 새로운 유한요소해석 프로그램을 개발하였다. 기존의 Macro-element법은 배수재의 과잉간극수압을 0으로 하여 연직배수량을 산정하였으나, 본 연구에서 개발된 프로그램은 부(-)의 과잉간극수압을 실제 진공압밀 조건과 동일하게 고려할 수 있도록 개선하였다. 프로그램의 성능 검증을 위해 진공압밀공법 적용 현장의 계측치와 비교한 결과, 프로그램으로 예측한 결과와 현장 계측데이터는 동일한 침하거동을 나타내었다.

• 산업기술연구
• /
• 제21권A호
• /
• pp.293-301
• /
• 2001

This paper is experimental results of investigating the efficiency of horizontal vacuum drainage system. Effects of size and shape of drain on horizontal vacuum drainage were studied. Model tests in the laboratory with soft marine clay were carried out with drain pipe of having three different diameters and PBD (Plastic Board Drain) of strip shape so that consolidation settlement of soft clay due to applied vacuum pressure, amount of discharge, ground settlement and distributions of pore pressure and undrained shear strength were measured during testing. From results of model test, amount of discharge due to vacuum pressure was increased with the diameter of pipe drain whereas the drain efficiency of pipe in per unit area of drain surface was decreased with diameter of pipe. The rate of discharge per unit time was reduced very fast with diameter of pipe. Settlement of ground surface with time was increased with diameter of pipe as a result of increase of discharge to drain pipe.

• 펄프종이기술
• /
• 제32권3호
• /
• pp.10-17
• /
• 2000

The MDDA(Modified Dynamic Drainage Analyzer) was developed to evaluate the drainage at hydrofoil table roll and low vacuum devices on fourdrinier paper machine MB-former. Comparison of the results was obtained using a computer simulation system based on Taylor's equation and filtration equation and by measuring the consistency profile in a paper machine presented an agreement within 10.7% This device can evaluate the dewatering pro-file on wire for various stock properties adjust dewatering devices on fourdrinier paper machine and control the dosage of retention aids for improving paper structural properties and runnability of papermachine.