• Korean Journal of Human Ecology
• /
• v.5 no.2
• /
• pp.55-74
• /
• 2002

This study, observing each respectively packaged Kongdduk during 12-day storing period and comparing it with unpackaged Kongdduk, through a cross-sectional view of its fiber and temperament, through a sensory evaluation rheometer measurement of rheological change depending on storing period and packaging type and through the organic acid content, micro-organic change, and retrogressive process. The results are as follows: 1. Kongdduk made of bean oil shows better chewiness, cohesiveness, and moistness than Kongdduk made of bean flour while Kongdduk made of bean flour shows better rheological properties as to roasted nutty taste or roasted nutty order. 2. The test of the cutted loaves of Kongdduk shows that adding oil of proper proportion to the dough of steamed rice cake in accordance with the amount of rice flour has a good influence on rheological properties of softness. 3. Rice cakes were prepared by addition of yellow soybean flour or peanut flour and packaged with CMP or VP, and their physical characteristics were monitored by sensory evaluation and mechanical measurement while storing for 6 days. For VP samples, yellow soybean rice cake showed little changes in cohesiveness, moistness and chewiness for 6 days of storage, while pure rice cake and peanut rice cake showed an increase in strength and hardness from the 4th day of storage. In case of CMP, yellow soybean rice cake hardly showed a difference in cohesiveness, moistness and chewiness for 6 days, while pure rice cake and peanut rice cake showed a significant difference from the 4th day in sensory evaluation. 4. For rheometer measurement, yellow soybean rice cake with CMP or VP showed little changes in strength or hardness for 6 days, while peanut rice cake and pure rice cake showed a drastic decrease in cohesiveness, from the End day and adhesiveness from the 4th day of storage. As there was no remarkable difference or deterioration for 6 days of storage in yellow soybean rice cake between CMP and VP, the ingredients of rice cakeappeared to be more important than the type of packaging in terms of quality deterioration of rice cake. 5. As the storing period passed by, organic acid is detected less at CMP-packaged Knngdduk than at wrapped. and its increasing speed proves to be slower as well. 6. The one wrapped with plyethylene film began to get moldy from pure rice cake or Kongdduk (rice cake mixed with yellow soybean or peanut) after 6 days, and more and more modly after 9 daysor after 12 days, but the CMP-packaged ones didn't get modly until 12 days or more. 7. CMP-packaged Kongdduk showed higher enthalpy of retrogradation than PE-wrapped one. As storing Period Passed by, Kongdduk,s enthalpy grew high. That is to say, it shows that Kongdduk got retrograded.

• Korean Chemical Engineering Research
• /
• v.54 no.2
• /
• pp.145-151
• /
• 2016

In response to the cavitation caused by the partial vacuum caused by the fluid flow, a paint was developed by dispersing the lamella-shaped glass-flake in resin for anti-cavitation. This composite paint was developed by using the inorganic filler (lamella shaped glass-flake) and the NBR (Acrylonitrile-butadiene rubber) which was modified epoxy resin. Especially, the glass-flake was a thin film with a thickness of about 100~200 nm and length of about $20{\sim}30{\mu}m$, the aspect ratio was about 200 to 300 times that of the plate-shaped. So the paint for anti-cavitation have shown excellent performance in corrosion resistance. The results of evaluating anti-cavitation performance was below, tensile strength $4.8{\sim}6N/mm^2$ or more, rupture elongation 30% or higher, abrasive speed $10mm^2/h$ or less. In particular, it showed more than twice the superior performance compared to existing advanced foreign products in anti-cavitation performance evaluation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.35 no.3
• /
• pp.566-576
• /
• 1997

This study was performed to evaluate the tensile strength of solder joint in titanium and the wettability of 14K gold solder on titanium. Two pieces of titanium rod 30 mm in length and 3mm in diameter were butt-soldered with a 14K gold solder using the electric resistance heating under flux-argon atmosphere, the infrared heating under argon atmosphere, and the infrared heating under vacuum-argon atmosphere. A tensile test was performed at a crosshead speed of 0.5 mm/min, and fracture surfaces were examined by SEM. To evaluate the wettability of 14K gold solder on titanium, titanum plates of a $17{\times}17{\times}1mm$ were polished with #80-#2000 emery papers, and the spreading areas of solder 10 mg were measured by heating at 840 * for 60 seconds. The solder-matrix interface regions were etched by the solution of 10% KCN-10% (NH4)2S2O8, and analyzed by EPMA. The results obtained were summarized as follows ; 1. The maximum tensile strength was obtained when the titanium surface was polished with #2000 emery paper and soldered using the electric resistance heating under flux-argon atmosphere. Soldering strengths showed the significant difference between the electric resistance heating and the infrared heating(p<0.05). 3. The fracture surfaces showed the aspect of brittle fracture, and the failure developed along the interfaces of solder-matrix reaction zone. 4. The EPMA data for the solder-matrix interface region revealed that the diffusion of Au and Cu occurred to the titanium matrix, and the reaction zone showed the higher contents of Au, Cu and Ti than others.

• Journal of the Korean Institute of Gas
• /
• v.20 no.6
• /
• pp.37-42
• /
• 2016

The purpose of this paper is to study for the emission gas control of passenger car. The first example, the PCSV never open when operating condition, but it opened by causing malfunction because of trouble. As a result, the purge gas entered into surge tank, a mount of fuel was displayed with excessive supply on tester. Therefore, it certified the bad-condition of the engine when idling by decreasing of fuel injection quantity from engine ECU. The second example, the hose activating a EGR valve didn't supply the vacuum pressure because of assembling the other part. Thus, it knew the bad-condition of engine that the EGR valve would not work normally by leaking with the other port. The third example, as the rear oxygen sensor of two sensor were fault-installing by changing the sensor of other a car it could not detect of oxygen quantity. Finally, it found the phenomenon of abruptly decreasing vehicle speed when braking a car. Therefore, the system including with emission control has to drastically manage by maximizing condition to role decreasing the emission gas.

• Journal of the Korean Society of Radiology
• /
• v.17 no.3
• /
• pp.441-447
• /
• 2023

Lead(Pb), which is currently mainly used for shielding purposes in the medical radiation, has excellent radiation shielding functions, but is continuously exposed to radiation directly or indirectly due to the harmfulness of lead itself to the human body and the inconvenience caused by its heavy weight. Research on shielding materials that are human-friendly, lightweight, and convenient to use that can block risks and replace lead is continuously being conducted. In this study, based on the commonly used polyethylene terephthalate (PET) film and the fabric material used in actual radiation protective clothing, a multi-layer thin film was realized through sputtering and vacuum deposition of bismuth, tungsten, and tin, which are metal materials that can shield radiation. Thus, a shielding film was produced and its applicability as a radiation shielding material was evaluated. The radiation shielding film was manufactured by establishing the optimized conditions for each shielding material while controlling the applied voltage, roll driving speed, and gas supply amount to manufacture the shielding film. The adhesion between the parent material and the shielding metal thin film was confirmed by Cross-cut 100/100, and the stability of the thin film was confirmed through a hot water test for 1 hour to measure the change of the thin film over time. The shielding performance of the finally realized shielding film was measured by the Korea association for radiation application (KARA), and the test conditions (inverse wide beam, tube voltage 50 kV, half layer 1.828 mmAl) were set to obtain an attenuation ratio of 16.4 (initial value 0.300 mGy/s, measured value 0.018 mGy/s) and damping ratio 4.31 (initial value 0.300 mGy/s, measured value 0.069 mGy/s) were obtained. by securing process efficiency for future commercialization, light and shielding films and fabrics were used to lay the foundation for the application of films to radiation protective clothing or construction materials with shielding functions.