• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.1
• /
• pp.23-29
• /
• 2000

The agglomeration of titania particles with 30 nm in radii was simulated based on the colloidal stability. For surface potential increase from 4.5 to 16.8 mV the height of energy barrier increased. This tendency may explain the experimentally observed aggregation behavior where particles with smaller size and higher potential exhibited higher stability but form bigger and harder agglomerates with irregular shapes after drying.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.05a
• /
• pp.197-205
• /
• 1999

소형 히트파이프에서 ？을 구리망사 또는 그루브를 적용할 수 있고 그루브 형상은 U, V 등 다양하다. 망사？은 모세압이 큰 잇점이 있어나 제작 단가가 높다. 그루브？은 대량생산이 용이하나 전밀 가공 기술이 요구된다. 현재까지 국내에서는 노트북 PC의 CPU 냉각에 사용한 소형 히트파이프의 전량을 해외에서 구매하고 있다. 본 연구에서는 직경 7 mm U형 그루브 관을 인발하여 관직경을 축소한 결과 내경 3.6 mm의 외경 4mm 의 V형 그루브관을 얻을 수 있었다. 이 관을 이용하여 소형 히트파이프를 제작하고 열전달 성능 시험을 수행하였다. 열전달 한계는 40~6$0^{\circ}C$ 범위작동온도 경사각 0$^{\circ}$ 에서 3 W를 얻을 수 있었다. U형 그루브 히트파이프에 비하여 모세압 저하로 인하여 낮은 값을 나타내었다. 열저항을 약 0.7~l.3 $^{\circ}C$/W 로 U형 그루브와 유사하였다.

• Journal of Korea Foundry Society
• /
• v.17 no.5
• /
• pp.488-493
• /
• 1997

주방상태 및 열처리를 행한 다합금계백주철(Fe-5%Cr-5%V-5%Mo-5%W-X%C(X=0.5, 1.0, 1.5, 2.0, 2.5, 3.0)에 있어서 탄소함량이 탄화물의 형태 및 잔류오스테나이트의 함량에 미치는 영향에 관하여 연구하였다. 주방상태의 경우, 2.0% 이하의 탄소함량에서는 편상MC 및 층상 $M_2C$탄화물만 관찰되었으나 2.5%C 이상의 경우, 편상 및 괴상MC, 층상$M_2C$ 그리고 셀형 $M_7C_3$탄화물이 관찰되었다. 또한, 기지조직내 오스테나이트의 함량도 탄소첨가와 더불어 점차 증가하여 2.5%C에서 84.8%의 최대함량을 나타낸 후, 3.0%C에서는 다시 감소하였다. 또한 열처리한 시편의 경우, 1차탄화물의 형상은 주방상태의 그것과 비슷하였으나 열처리중 기지조직내 용해되었던 C, Cr, V, Mo, W등이 아주 미세한 2차탄화물의 형태로 석출되어 기지조직내 오스테나이트의 함량은 주방상태의 그것에 비해 감소하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4191-4196
• /
• 2013

In this paper, structural analysis was made on two cases in order to develop free rotational method and rotational angle in LCD monitor. The configuration of LCD monitor in field was modeled by using 3-D design program CATIA V5 and structural analysis was done to the modeled LCD in order to obtain stress, strain and total deformation by using ANSYS finite element analysis program.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.155-155
• /
• 2009

The copper plating was deposited by pulse reverse current (PRC) method with additives. The all specimens were first immersted in 10% H2SO4 for 10 minutes, and then were rinsed with deionized water. The current densities of forward pulse were 400mA/$cm^2$, and those of reverse pulse were 1900mA/$cm^2$ and 100mA/$cm^2$. Results are compared for different additives for pulse plating conditions. When it added in Only CH4N2S (TU) or only C10H13NO3S (SVH), the effect of surface side growth of Cu was not different. But when it added in TU and SVH, surface side growth of Cu decreased. Polarization curves were measured from OCP to -0.7 V at a rate of 1mV/sec. Each specimen was observed under the PHENOM to see surface morphology.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.3
• /
• pp.1-7
• /
• 2003

The crystallized stable cobalt silicide$(CoSi_2)$ films were prepared on $poly-Si/SiO_2/Si$substrates for the application of inkjet printing head as a heating element with omega shape. The structural images and temperature resistance coefficient were investigated. The value of temperature resistance coefficient of the heating element was found to be about $0.0014/^{\circ}C$. The maximum power of the heating element was 2 W at the applied voltage of 2 V, 10 kHz in frequency and $1{\mu}s$ in pulse width. From the investigation of fatigue property according to the repeated applied voltages, there was no drastic changes in the resistances of heating element under the condition of $10^8$ pulsed cycles at below 15 V biased voltage. In contrast, the resistance of heating element was greatly increased at $10^6$ pulsed cycles when the heating element was operated at 17 V.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.59-66
• /
• 2020

In this study, the characteristics of ITO thin film was investigated to finding a low cost and highly transparent electrodes for display of mobile communication devices. The ITO film was deposited by DC magnetron sputter. The experimental conditions were changed as follows: 1. ambient pressure changed 1 to 3 mTorr with 1mTorr step, 2. bias electric voltage changed with 10V step. The chamber was pumped out by rotary pump until 10^-3Torr then the diffusion pump was used to lower the pressure of 10^-6Torr. The results shows us the film growth was obvious when the bias voltage was larger than 300V, but the overall thickness tendency was existed: the more voltage is the thicker thickness. At 330V bias voltage condition, the deposition rate was the largest and apparent grain was showed.

• Journal of the Korean Society of Radiology
• /
• v.16 no.1
• /
• pp.53-59
• /
• 2022

DEXA, as the standard areal bone mineral density (aBMD) measurement method, often shows an insuficient correlation between aBMDs of the measured bones and referring bones and is inaccurate due to the mass effect. In contrast, quantitative computer tomography (QCT), as a volumetric BMD (vBMD) measurement method, is being advanced so that it uses less radiation before, owing to improved CT device and computer imaging technology. Because dual-energy CTs can modulate the image signals showing tumor or specific chemicals as well as the ability to measure vBMD, they are expanding their application. For pre-checking vBMD of surgeon-specific bone volume at implantation candidate sites, a finite element creation-based local vBMD measurement technique was developed. The local vBMD measurement function for surgeon-specific shape volumes will be added to clinical imaging systems.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.6
• /
• pp.872-877
• /
• 2015

The Permanent Magnet (PM) machine used at speed control using field-weakening control method. But the field-weakening current, which reduces the field flux for high speeds, causes significant copper and core losses. Therefore, this paper deals with the PM performance evaluations in a pole changing memory motor (PCMM). The PCMM can change the number of magnetic poles and produce two types of torque. When the motor operates with eight poles, it produces a magnetic torque at low rotational speeds. When the motor changes to four poles, it produces both magnetic torque and reluctance torque at high speeds. The paper explain the principle and basic characteristics of the motor by using a finite element method magnetic-field analysis, which consists of a PM magnetized by a pulse d-axis current of the armature winding. The results of our experiment show that the proposed motor reduces core loss by 10% and 55% under no-load and load conditions, and doubles the speed range of the motor.

• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.29-35
• /
• 2004

Fine blanking can be considered as a manufacturing process capable of producing sheet metal parts with completely smooth edges that may be hardly obtained by conventional shear-cutting procedures. This fact, together with the considerable economic advantages offered by this process, has been responsible for the rapid acceptance of fine blanking throughout the manufacturing industry all over the world, and the discovery of many new applications. This study was performed to investigate the effect of clearance and V-ring shape on the quality of sheared surface in a fine blanking process. The critical value needed to apply the normalized Cockcroft-Latham fracture criterion to the simulation of fine blanking is obtained by correlating the result of finite element analysis and that of experiment for the uniaxial tensile test. From finite element analysis of an axisymmetric fine blanking process, it has been found that punch load, die-roll depth, burnish zone size and shape of sheared surface are considerably influenced by clearance and V-ring shape.