• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.28 no.2
• /
• pp.183-193
• /
• 1995

Assuming that fishing nets are porous structures to suck water into their mouth and then filtrate water out of them, the flow resistance N of nets with wall area S under the velicity v was taken by $R=kSv^2$, and the coefficient k was derived as $$k=c\;Re^{-m}(\frac{S_n}{S_m})n(\frac{S_n}{S})$$ where $R_e$ is the Reynolds' number, $S_m$ the area of net mouth, $S_n$ the total area of net projected to the plane perpendicular to the water flow. Then, the propriety of the above equation and the values of c, m and n were investigated by the experimental results on plane nettings carried out hitherto. The value of c and m were fixed respectively by $240(kg\cdot sec^2/m^4)$ and 0.1 when the representative size on $R_e$ was taken by the ratio k of the volume of bars to the area of meshes, i. e., $$\lambda={\frac{\pi\;d^2}{21\;sin\;2\varphi}$$ where d is the diameter of bars, 21 the mesh size, and 2n the angle between two adjacent bars. The value of n was larger than 1.0 as 1.2 because the wakes occurring at the knots and bars increased the resistance by obstructing the filtration of water through the meshes. In case in which the influence of $R_e$ was negligible, the value of $cR_e\;^{-m}$ became a constant distinguished by the regions of the attack angle $ \theta$ of nettings to the water flow, i. e., 100$(kg\cdot sec^2/m^4)\;in\;45^{\circ}<\theta \leq90^{\circ}\;and\;100(S_m/S)^{0.6}\;(kg\cdot sec^2/m^4)\;in\;0^{\circ}<\theta \leq45^{\circ}$. Thus, the coefficient $k(kg\cdot sec^2/m^4)$ of plane nettings could be obtained by utilizing the above values with $S_m\;and\;S_n$ given respectively by $$S_m=S\;sin\theta$$ and $$S_n=\frac{d}{I}\;\cdot\;\frac{\sqrt{1-cos^2\varphi cos^2\theta}} {sin\varphi\;cos\varphi} \cdot S$$ But, on the occasion of $\theta=0^{\circ}$ k was decided by the roughness of netting surface and so expressed as $$k=9(\frac{d}{I\;cos\varphi})^{0.8}$$ In these results, however, the values of c and m were regarded to be not sufficiently exact because they were obtained from insufficient data and the actual nets had no use for k at $\theta=0^{\circ}$. Therefore, the exact expression of $k(kg\cdotsec^2/m^4)$, for actual nets could De made in the case of no influence of $R_e$ as follows; $$k=100(\frac{S_n}{S_m})^{1.2}\;(\frac{S_m}{S})\;.\;for\;45^{\circ}<\theta \leq90^{\circ}$$, $$k=100(\frac{S_n}{S_m})^{1.2}\;(\frac{S_m}{S})^{1.6}\;.\;for\;0^{\circ}<\theta \leq45^{\circ}$$

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.8 no.2
• /
• pp.47-60
• /
• 1975

For the calculation of population parameter and estimation of recruitment of a fish population, an application of multiple regression method was used with some statistical inferences. Then, the differences between the calculated values and the true parameters were discussed. In addition, this method criticized by applying it to the statistical data of a population of bigeye tuna, Thunnus obesus of the Indian Ocean. The method was also applied to the available data of a population of Pacific saury, Cololabis saira, to estimate its recuitments. A stock at t year and t+1 year is, $N_{0,\;t+1}=N_{0,\;t}(1-m_t)-C_t+R_{t+1}$ where $N_0$ is the initial number of fish in a given year; C, number o: fish caught; R, number of recruitment; and M, rate of natural mortality. The foregoing equation is $$\phi_{t+1}=\frac{(1-\varrho^{-z}{t+1})Z_t}{(1-\varrho^{-z}t)Z_{t+1}}-\frac{1-\varrho^{-z}t+1}{Z_{t+1}}\phi_t-a'\frac{1-\varrho^{-z}t+1}{Z_{t+1}}C_t+a'\frac{1-\varrho^{-z}t+1}{Z_{t+1}}R_{t+1}......(1)$$ where $\phi$ is CPUE; a', CPUE $(\phi)$ to average stock $(\bar{N})$ in number; Z, total mortality coefficient; and M, natural mortality coefficient. In the equation (1) , the term $(1-\varrho^{-z}t+1)/Z_{t+1}$s almost constant to the variation of effort (X) there fore coefficients $\phi$ and $C_t$, can be calculated, when R is a constant, by applying the method of multiple regression, where $\phi_{t+1}$ is a dependent variable; $\phi_t$ and $C_t$ are independent variables. The values of Mand a' are calculated from the coefficients of $\phi_t$ and $C_t$; and total mortality coefficient (Z), where Z is a'X+M. By substituting M, a', $Z_t$, and $Z_{t+1}$ to the equation (1) recruitment $(R_{t+1})$ can be calculated. In this precess $\phi$ can be substituted by index of stock in number (N'). This operational procedures of the method of multiple regression can be applicable to the data which satisfy the above assumptions, even though the data were collected from any chosen year with similar recruitments, though it were not collected from the consecutive years. Under the condition of varying effort the data with such variation can be treated effectively by this method. The calculated values of M and a' include some deviation from the population parameters. Therefore, the estimated recruitment (R) is a relative value instead of all absolute one. This method of multiple regression is also applicable to the stock density and yield in weight instead of in number. For the data of the bigeye tuna of the Indian Ocean, the values of estimated recruitment (R) calculated from the parameter which is obtained by the present multiple regression method is proportional with an identical fluctuation pattern to the values of those derived from the parameters M and a', which were calculated by Suda (1970) for the same data. Estimated recruitments of Pacific saury of the eastern coast of Korea were calculated by the present multiple regression method. Not only spring recruitment $(1965\~1974)$ but also fall recruitment $(1964\~1973)$ was found to fluctuate in accordance with the fluctuations of stock densities (CPUE) of the same spring and fall, respectively.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.15 no.4
• /
• pp.193-216
• /
• 2020

Due to the recent mid- to long-term slump and falling growth rates in the global economy, interest in organizational structures that create new products or services as a new alternative to survive and develop in an opaque environment both internally and externally, and enhance organizational sustainability through changes in production methods and business innovation is increasing day by day. In this atmosphere, we agree that the growth of small and medium-sized venture companies has a significant impact on the national economy, and various efforts are being made to enhance the technological innovation capabilities of the members so that these small and medium-sized venture companies can enhance and sustain their performance. The purpose of this study is also to investigate how the technological innovation capabilities of small and medium-sized venture companies correlate with the performance of knowledge management and to analyze the role of network capabilities to organize the strategic activities of enterprise to obtain the resources and organizational capabilities to be used for value creation from external networks. In other words, research was conducted on the impact of technological innovation capabilities of small and medium venture companies on knowledge management performance by using network capabilities as parameters. Therefore, in this study, we would like to verify the hypothesis that innovation capabilities will have a positive impact on knowledge management performance by using network capabilities of small and medium venture companies. Economic activities based on technological innovation capabilities should respond quickly to new changes in an environment where uncertainty has increased, and lead to macro-economic growth and development as well as overcoming long-term economic downturns so that they can become the nation's new growth engine as well as sustainable growth and survival of the organization. In addition, this study was conducted by setting the most important knowledge management performance within the organization as a dependent variable. As a result, R&D and learning capabilities among technological innovation capabilities have no impact on financial performance. In contrast, it was shown that corporate innovation activities have a positive impact on both financial and non-financial performance. The fact that non-financial factors such as quality and productivity improvement are identified in the management of small and medium-sized venture companies utilizing their technological innovation capabilities is contrary to a number of studies by those corporate innovation activities affect financial performance during prior research. The reason for this result is that research companies have been out of start-up companies for more than seven years, but sales are less than 10 billion won, and unlike start-up companies, R&D and learning capabilities have more positive effects on intangible non-financial performance than financial performance. Corporate innovation activities have been shown to have a positive (+) impact on both financial and non-financial performance, while R&D and learning capabilities have a positive (+) impact on financial performance by parameters of network capability. Corporate innovation activities have been shown to have no impact on both financial and non-financial performance, and R&D and learning capabilities have no impact on non-financial performance. It could be seen that the parameter effects of network competency are limited to when R&D and learning competencies are derived from quantitative financial performance. It could be seen that the parameter effects of network competency are limited to when R&D and learning competencies are derived from quantitative financial performance.

• Progress in Medical Physics
• /
• v.21 no.1
• /
• pp.52-59
• /
• 2010

To examine among patients with vertebral compression fracture the extent to which signal-to-noise ratio (SNR) and Apparent Diffusion Coefficient (ADC) values at the lumbar vertebral compression fracture site vary on diffusion-weighted MR images according to varying b values on the 1.5T MR device. Diffusion-weighted MR images of 30 patients with compression fracture due to chronic osteoporosis who underwent vertebral MRI from Jan. 2008 to Nov. 2009 were respectively obtained using a 1.5-T MR scanner with the b values increased from 400, 600, 800, 1,000 to $1,200\;s/mm^2$. For diffusion-weighted MR images with different b values, the signal-to-noise ratio (SNR) was assessed at three sites: the site of compression fracture of the lumbar vertebral body at L1 to L5, and both the upper and lower discs of the said fracture site, while for ADC map images with different b values, the SNR and ADC were respectively assessed at those three sites. As a quantitative analysis, diffusion-weighted MR images and ADC map images with b value of $400\;s/mm^2$ (the base b values) were respectively compared with the corresponding images with each different b value. As far as qualitative analysis is concerned, for both diffusion-weighted MR and ADC map images with b value of $400\;s/mm^2$, the extent to which signal intensity values obtained at the site of compression fracture of the lumbar vertebral body at L1 to L5 vary according to the increasing b values were examined. The quantitative analysis found that for both diffusion-weighted MR and ADC map images, as the b values increased, the SNR were relatively lowered at all the three sites, compared to the base b value. Also, it was found that as the b values increased, ADC valueswere relatively lowered at all the three sites on ADC map images. On the other hand, the qualitative analysis found that as the b values increased to more than $400\;s/mm^2$, the signal intensity gradually decreased at all the sites, while at the levels of more than $1,000\;s/mm^2$, severe image noises appeared at all of the three sites. In addition, higher signal intensity was found at the site of compression fracture of the lumbar vertebral body than at the discs. Findings showed that with the b value being increased, both the signal-to-noise ratio (SNR) and Apparent Diffusion Coefficient (ADC) values gradually decreased at all the sites of the lumbar vertebral compression fracture and both the upper and lower discs of the fracture site, suggesting that there is a possibility of a wider range of applications to assessment of various vertebral pathologies by utilizing multi b values in the diffusion-weighted MRI examination.

• Korean Journal of Organic Agriculture
• /
• v.16 no.1
• /
• pp.115-125
• /
• 2008

This study was conducted to determine adequate forage crop choice and optimal level of livestock manure, when different types and levels of the livestock manure were applied in corns or sorghum$\times$sorghum hybrids for the production of organic roughages by utilizing livestock manure. For the corn, yields of annual dry matter (DM) and total digestible nutrients (TDN) were highest in N+P+K-applied treatments, showing 17.3 and 11.7 ton/ha, respectively. Treatments applied 100% composted cattle manure (8.9 and 6.1 ton/ha) and 100% cattle slurry (9.4 and 7.5 ton/ ha) in contrast with chemical fertilizer-N had higher yields of DM and TDN than no fertilizer (4.8 and 2.7 ton/ha) and P+K-applied treatments (8.8 and 6.0 ton/ha). Particularly, treatments applied 150% composted cattle manure and 150% cattle slurry were markedly higher, which represented 11.4 and 7.6 ton/ha and 10.3 and 7.3 ton/ha, respectively. Crude protein (CP) contents for corns applied livestock manure ranged from 5.6 to 6.6%, which were significantly (p<0.05) higher than those of no fertilizer (3.9%) and P+K-applied treatments (5.5%). ADF (42.4%) and NDF (58.3%) contents for no fertilizer treatment were significantly (p<0.05) higher than those of other treatments. However, TDN contents were higher for livestock manure treatments than for no and/or chemical fertilizer treatments. In particular, TDN contents of treatments applied 150% composted cattle manure and 150% cattle slurry showed 72.3 and 70.8%, respectively and both treatments were significantly (p<0.05) higher than all of the other treatments. For the sorghum$\times$sorghum hybrid, yields of annual DM and TDN for 100% (12.4 and 7.4 ton/ha) and 150% (13.1 and 7.6 ton/ha) cattle slurry-applied treatments, and N+P+K-applied treatments (12.6 and 7.7 ton/ha) were significantly (p<0.05) higher than those of the others. In the others, 150% composted cattle manure (9.3 and 5.2 ton/ha) had higher annual DM and TDN yields than P+K-applied (8.4 and 4.8 ton/ha) and 100% composted cattle manure treatments (7.4 and 4.2 ton/ha), with no significant difference. Crude protein contents for sorghum$\times$sorghum hybrid applied P+K and cattle slurry were 8.8 and 8.6%, respectively. CP contents for both treatments were significantly higher than those of composted manure ($7.5{\sim}8.3%$) and no fertilizer (4.0%) treatments, but 100% livestock manure treatments had higher CP contents than 150%-applied treatments. ADF and NDF contents for N+P+K and cattle slurry-applied treatments were significantly (p<0.05) lower than the others. However, TDN contents were highest in N+P+K and cattle slurry-applied treatments, showing 61.2 and 58.3 to 59.4%, respectively. These results indicated that application of livestock manure instead of chemical fertilizer to the soil of forage crops might not only improve yields of DM and TDN, but also reduce environmental pollution by producing organic roughages through recycling of livestock manure.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.3
• /
• pp.196-213
• /
• 2001

A split beam ultrasonic transducer operating at a frequency of 70 kHz to use in the fish sizing echo sounder was developed and the acoustic radiation characteristics were experimentally analyzed. The amplitude shading method utilizing the properties of the Chebyshev polynomials was used to obtain side lobe levels below -20 dB and to optimize the relationship between main beam width and side lobe level of the transducer, and the amplitude shading coefficient to each of the elements was achieved by changing the amplitude contribution of elements with 4 weighting transformers embodied in the planar array transducer assembly. The planar array split beam transducer assembly was composed of 36 piezoelectric ceramics (NEPEC N-21, Tokin) of rod type of 10 mm in diameter and 18.7 mm in length of 70 kHz arranged in the rectangular configuration, and the 4 electrical inputs were supplied to the beamformer. A series of impedance measurements were conducted to check the uniformity of the individual quadrants, and also in the configurations of reception and transmission, resonant frequency, and the transmitting and receiving characteristics were measured in the water tank and analyzed, respectively. The results obtained are summarized as follows : 1. Average resonant and antiresonant frequencies of electrical impedance for four quadrants of the split beam transducer in water were 69.8 kHz and 83.0 kHz, respectively. Average electrical impedance for each individual transducer quadrant was 49.2$\Omega$ at resonant frequency and 704.7$\Omega$ at antiresonant frequency. 2. The resonance peak in the transmitting voltage response (TVR) for four quadrants of the split beam transducer was observed all at 70.0 kHz and the value of TVR was all about 165.5 dB re 1 $\mu$Pa/V at 1 m at 70.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The resonance peak in the receiving sensitivity (SRT) for four combined quadrants (quad LU+LL, quad RU+RL, quad LU+RU, quad LL+RL) of the split beam transducer was observed all at 75.0 kHz and the value of SRT was all about -177.7 dB re 1 V/$\mu$Pa at 75.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The sum beam transmitting voltage response and receiving senstivity was 175.0 dB re 1$\mu$Pa/V at 1 m at 75.0 kHz with bandwidth of 10.0 kHz, respectively. 3. The sum beam of split beam transducer was approximately circular with a half beam angle of $9.0^\circ$ at -3 dB points all in both axis of the horizontal plane and the vertical plane. The first measured side lobe levels for the sum beam of split beam transducer were -19.7 dB at $22^\circ$ and -19.4 dB at $-26^\circ$ in the horizontal plane, respectively and -20.1 dB at $22^\circ$ and -22.0 dB at $-26^\circ$ in the vertical plane, respectively. 4. The developed split beam transducer was tested to estimate the angular position of the target in the beam through split beam phase measurements, and the beam pattern loss for target strength corrections was measured and analyzed.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.34 no.1
• /
• pp.40-52
• /
• 2016

Buyongjeong, a pavilion in the Rear Garden of Changdeok Palace, was appointed as Treasure No. 1763 on March 2, 2012, by the South Korea government since it shows significant symmetry and proportion on its unique planar shape, spatial configuration, building decoration, and so forth. However, the designation of Treasure selection was mainly evaluated by concrete science, in that the selection has not clearly articulated how and why Buoungjeong was constructed as a present unique form. Therefore, this study aims to clarify the identity of Buyongjeong at the time of construction by considering its historical, ideological, philosophical background and building intention. Summary are as follows: First, Construction backgrounds and characters of Buyongjeong: Right after the enthronement, King Jeongjo had founded Kyujanggak(奎章閣), and sponsored civil ministers who were elected by the national examination, as a part of political reform. In addition, he established his own political system by respecting "Kaksin(閣臣)", Kyujanggak's officials as much as "Kain(家人)", internal family members. King Jeongjo's aggressive political reform finally enabled King's lieges to visit King's Rear Garden. In the reign of King Jeongjo's 16th year(1792), Naekaksangjohoe(內閣賞釣會) based on "Kaksin" was officially launched and the Rear Garden visitation became a regular meeting. The Rear Garden visitation consisted of "Sanghwajoeoyeon(賞花釣魚宴)" - enjoying flowers and fishing, and activities of "Nanjeongsugye". Afterward, it eventually became a huge national event since high rank government officials participated the event. King Jeongjo shared the cultural activities with government officials together to Buyongjeong as a place to fulfill his royal politics. Second, The geographical location and spatial characteristics of Buyongjeong: On the enthronement of King Jeongjo(1776), he renovated Taeksujae. Above all, aligning and linking Gaeyuwa - Taeksujae - a cicular island - Eosumun - Kyujangkak along with the construction axis is an evidence for King Jeongjo to determine how the current Kyujangkak zone was prepared and designed to fulfill King Jeonjo's political ideals. In 17th year(1793) of the reign of King Jeongjo, Taeksujae, originally a square shaped pavilion, was modified and expanded with ranks to provide a place to get along with the King and officials. The northern part of Buyongjeong, placed on pond, was designed for the King's place and constructed one rank higher than others. Discernment on windows and doors were made with "Ajasal" - a special pattern for the King. The western and eastern parts were for government officials. The center part was prepared for a place where government officials were granted an audience with the King, who was located in the nortern part of Buyongjeong. Government officials from the western and eastern parts of Buyongjeong, could enter the central part of the Buyongjeong from the southern part by detouring the corner of Buyongjeong. After all, Buyongjeong is a specially designed garden building, which was constructed to be a royal palace utilizing its minimal space. Third, Cultural Values of Buyongjeong: The Buyongjeong area exhibits a trait that it had been continuously developed and it had reflected complex King's private garden cultures from King Sejo, Injo, Hyunjong, Sukjong, Jeongjo and so forth. In particular, King Jeongjo had succeded physical, social and imaginary environments established by former kings and invited their government officials for his royal politics. As a central place for his royal politics, King Jeongjo completed Buyongjeong. Therefore, the value of Buyongjeong, as a garden building reflecting permanency of the Joseon Dynasty, can be highly evaluated. In addition, as it reflects Confucianism in the pavilion - represented by distinguishing hierarchical ranks, it is a unique example to exhibit its distinctiveness in a royal garden.

• Journal of Intelligence and Information Systems
• /
• v.24 no.1
• /
• pp.101-124
• /
• 2018

Recently, most of the technologies have been developed in various forms through the advancement of single technology or interaction with other technologies. Particularly, these technologies have the characteristic of the convergence caused by the interaction between two or more techniques. In addition, efforts in responding to technological changes by advance are continuously increasing through forecasting promising convergence technologies that will emerge in the near future. According to this phenomenon, many researchers are attempting to perform various analyses about forecasting promising convergence technologies. A convergence technology has characteristics of various technologies according to the principle of generation. Therefore, forecasting promising convergence technologies is much more difficult than forecasting general technologies with high growth potential. Nevertheless, some achievements have been confirmed in an attempt to forecasting promising technologies using big data analysis and social network analysis. Studies of convergence technology through data analysis are actively conducted with the theme of discovering new convergence technologies and analyzing their trends. According that, information about new convergence technologies is being provided more abundantly than in the past. However, existing methods in analyzing convergence technology have some limitations. Firstly, most studies deal with convergence technology analyze data through predefined technology classifications. The technologies appearing recently tend to have characteristics of convergence and thus consist of technologies from various fields. In other words, the new convergence technologies may not belong to the defined classification. Therefore, the existing method does not properly reflect the dynamic change of the convergence phenomenon. Secondly, in order to forecast the promising convergence technologies, most of the existing analysis method use the general purpose indicators in process. This method does not fully utilize the specificity of convergence phenomenon. The new convergence technology is highly dependent on the existing technology, which is the origin of that technology. Based on that, it can grow into the independent field or disappear rapidly, according to the change of the dependent technology. In the existing analysis, the potential growth of convergence technology is judged through the traditional indicators designed from the general purpose. However, these indicators do not reflect the principle of convergence. In other words, these indicators do not reflect the characteristics of convergence technology, which brings the meaning of new technologies emerge through two or more mature technologies and grown technologies affect the creation of another technology. Thirdly, previous studies do not provide objective methods for evaluating the accuracy of models in forecasting promising convergence technologies. In the studies of convergence technology, the subject of forecasting promising technologies was relatively insufficient due to the complexity of the field. Therefore, it is difficult to find a method to evaluate the accuracy of the model that forecasting promising convergence technologies. In order to activate the field of forecasting promising convergence technology, it is important to establish a method for objectively verifying and evaluating the accuracy of the model proposed by each study. To overcome these limitations, we propose a new method for analysis of convergence technologies. First of all, through topic modeling, we derive a new technology classification in terms of text content. It reflects the dynamic change of the actual technology market, not the existing fixed classification standard. In addition, we identify the influence relationships between technologies through the topic correspondence weights of each document, and structuralize them into a network. In addition, we devise a centrality indicator (PGC, potential growth centrality) to forecast the future growth of technology by utilizing the centrality information of each technology. It reflects the convergence characteristics of each technology, according to technology maturity and interdependence between technologies. Along with this, we propose a method to evaluate the accuracy of forecasting model by measuring the growth rate of promising technology. It is based on the variation of potential growth centrality by period. In this paper, we conduct experiments with 13,477 patent documents dealing with technical contents to evaluate the performance and practical applicability of the proposed method. As a result, it is confirmed that the forecast model based on a centrality indicator of the proposed method has a maximum forecast accuracy of about 2.88 times higher than the accuracy of the forecast model based on the currently used network indicators.

• Journal of Intelligence and Information Systems
• /
• v.24 no.3
• /
• pp.177-198
• /
• 2018

Recently, as economic property it has become necessary to acquire and utilize the framework for water resource measurement and performance management as the property of water resources changes to hold "public property". To date, the evaluation of water technology has been carried out by feasibility study analysis or technology assessment based on net present value (NPV) or benefit-to-cost (B/C) effect, however it is not yet systemized in terms of valuation models to objectively assess an economic value of technology-based business to receive diffusion and feedback of research outcomes. Therefore, K-water (known as a government-supported public company in Korea) company feels the necessity to establish a technology valuation framework suitable for technical characteristics of water resources fields in charge and verify an exemplified case applied to the technology. The K-water evaluation technology applied to this study, as a public interest goods, can be used as a tool to measure the value and achievement contributed to society and to manage them. Therefore, by calculating the value in which the subject technology contributed to the entire society as a public resource, we make use of it as a basis information for the advertising medium of performance on the influence effect of the benefits or the necessity of cost input, and then secure the legitimacy for large-scale R&D cost input in terms of the characteristics of public technology. Hence, K-water company, one of the public corporation in Korea which deals with public goods of 'water resources', will be able to establish a commercialization strategy for business operation and prepare for a basis for the performance calculation of input R&D cost. In this study, K-water has developed a web-based technology valuation model for public interest type water resources based on the technology evaluation system that is suitable for the characteristics of a technology in water resources fields. In particular, by utilizing the evaluation methodology of the Institute of Advanced Industrial Science and Technology (AIST) in Japan to match the expense items to the expense accounts based on the related benefit items, we proposed the so-called 'K-water's proprietary model' which involves the 'cost-benefit' approach and the FCF (Free Cash Flow), and ultimately led to build a pipeline on the K-water research performance management system and then verify the practical case of a technology related to "desalination". We analyze the embedded design logic and evaluation process of web-based valuation system that reflects characteristics of water resources technology, reference information and database(D/B)-associated logic for each model to calculate public interest-based and profit-based technology values in technology integrated management system. We review the hybrid evaluation module that reflects the quantitative index of the qualitative evaluation indices reflecting the unique characteristics of water resources and the visualized user-interface (UI) of the actual web-based evaluation, which both are appended for calculating the business value based on financial data to the existing web-based technology valuation systems in other fields. K-water's technology valuation model is evaluated by distinguishing between public-interest type and profitable-type water technology. First, evaluation modules in profit-type technology valuation model are designed based on 'profitability of technology'. For example, the technology inventory K-water holds has a number of profit-oriented technologies such as water treatment membranes. On the other hand, the public interest-type technology valuation is designed to evaluate the public-interest oriented technology such as the dam, which reflects the characteristics of public benefits and costs. In order to examine the appropriateness of the cost-benefit based public utility valuation model (i.e. K-water specific technology valuation model) presented in this study, we applied to practical cases from calculation of benefit-to-cost analysis on water resource technology with 20 years of lifetime. In future we will additionally conduct verifying the K-water public utility-based valuation model by each business model which reflects various business environmental characteristics.

• Culinary science and hospitality research
• /
• v.22 no.7
• /
• pp.112-130
• /
• 2016

In this study the moisture content and chromaticity of fresh made lotus leaf powder added Cheongpomuk to utilize various efficacy of lotus leaf for processed food, as well as chromaticity, moisture content change, texture, total phenolic compound content, DPPH radical scavenging ability and preference of lotus leaf powder added Cheongpomuk with different storage period have been measured and analyzed. From the texture of lotus leaf powder added mung bean as per the storage period, the hardness of fresh Cheongpomuk were $0.38g/cm^2$ from control group, $0.40g/cm^2$ from CCD 1% group, $0.42g/cm^2$ from CCD 3% group, $0.37g/cm^2$ from CCD 5% group, $0.42g/cm^2$ from GGD 1% group, $0.39g/cm^2$ from GGD 3% group, $0.35g/cm^2$ from GGD 5% group, $0.39g/cm^2$ from JLD 1% group, $0.33g/cm^2$ from JLD 3% group, and $0.32g/cm^2$ from JLD 5% group. It has shown that JLD 5% group was the lowest, while CCD 3% group and GGD 1% group were the highest, and there were significant differences among sample groups. For DPPH radical scavenging ability, that of GLD 5% group was 22 times higher than that of control group. In addition, the tendency was increasing by increasing the adding rate of lotus leaf powder though there was some tolerance among sample groups. For total phenolic compound content, that of control group was 6.65 mg CE/100 g, and others were 7.48 mg CE/100 g from CCD 1% group, 15.82 mg CE/100 g from CCD 3% group, 20.15 mg CE/100 g from CCD 5% group, 15.55mg CE/100 g from GGD 1% group, 23.02 mg CE/100 g from GGD 3%, 26.95 mg CE/100 g from GGD 5% group, 3.92 mg CE/100 g from JLD 1% group, 16.72 mg CE/100 g from JLD 3%, and 26.58 mg CE/100 from JLD 5% group. From the analyzing result of responses for color and scent, taste, elasticity, and total preference of lotus leaf powder added Cheongpomuk between two panel groups, there was significant difference for the color, higher from professional cooking instructor group, but there were no significant difference between two groups for all other factors among professional cooking instructors and cooking department students. According to the results, it is expected that various functional foods can be developed by utilizing lotus leaf powder, depending on the growth condition and cultural environment of each region by adding 3% of lotus leaf powder, would be the most suitable recipe for Cheongpomuk.