• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.04a
• /
• pp.39-53
• /
• 1993

The minimum oil film thickness(MOFT) in the connecting-rod bering of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film charactrtistics. And cylinder pressure, crank-pin surface temperature and bearing tenp ture are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable detmuuination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Tribology and Lubricants
• /
• v.10 no.1
• /
• pp.14-26
• /
• 1994

The minimum oil film thickness(MOFT) in the connecting-rod bearing of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film characteristics. And cylinder pressure, crank-pin surface temperature and bearing temperature are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable determination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.113-119
• /
• 2014

Due to the development of the petroleum refining technology and continuously increased demand from markets, a quantity of gasoline and diesel oil produced from a restricted quantity of crude oil has been increasing, and residual fuel to be used at marine diesel engines has been gradually becoming low quality. As a result, it was recently reported that trouble oils which cause abnormal combustion such as knocking with extreme noise and misfire from internal combustion engines were increasing throughout the world. In this study, an author investigated ignitability and combustion quality by using combustion analyzer with constant volume(FCA, Fuel Combustion Analyzer) and middle speed diesel engine about MDO(Marine Diesel Oil), HFO(Heavy Fuel Oil), LCO(Light Cycle Oil) and Blend-HFO which was blended LCO of 1000 liters with HFO of 600 liters. Moreover, for betterment of ignitability and combustion quality of injected fuels, multi-injection experiment was carried out in the diesel engine using Blend-HFO. According to the results of FCA analysis, ignitability and combustion quality was bad in the order of MDO

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.421-422
• /
• 2002

The purpose of this paper is to investigate the leakage characteristics of the valve stem in the gasoline engines. Especially, three factors affecting oil leakage are the power cylinder, engine head system, and the positive crankcase ventilation system. Which is the most variables, analysis difficulty is the valve stem seal characteristics. The testing system is used with oil motoring system. The leakage of an engine is analyzed for the cylinder temperature, atmosphere pressure, positive pressure, negative pressure, revolution of the camshaft and the surface roughness of the valve stem.

• Journal of ILASS-Korea
• /
• v.21 no.3
• /
• pp.144-154
• /
• 2016

This review will be concentrated on the spray characteristics of biobutanol and its blends fuels in internal combustion engines including compression ignition, spark ignition and gas turbine engines. Butanol can be produced by fermentation from sucrose-containing feedstocks, starchy materials and lignocellulosic biomass. Among four isomers of butanol, n-butanol and iso-butanol has been used in CI and SI engines. This is due to higher octane rating and lower water solubility of both butanol compared with other isomers. The researches on the spray characteristics of neat butanol can be classified into the application to CI and SI engines, particularly GDI engine. Two empirical correlations for the prediction of spray angle for butanol as a function of Reynolds number was newly suggested. However, the applicability for the suggested empirical correlation is not yet proved. The butanol blended fuels used for the investigation of spray characteristics includes butanol-biodiesel blend, butanol-gasoline blend, butano-jet A blend and butanol-other fuel blends. Three blends such as butanol/ethanol, butanol/heptane and butanol/heavy fuel oil blends are included in butanol-other fuel blends. Even though combustion and emission characteristics of butanol/diesel fuel blend in CI engines were broadly investigated, study on spray characteristics of butanol/diesel fuel blend could not be found in the literature. In addition, the more study on the spray characteristics of butanol /gasoline blend is required.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.11
• /
• pp.1163-1168
• /
• 2011

Compared with the spark-ignition gasoline engine, the compression-ignition diesel engine has reduced fuel consumption due to its higher thermal efficiency. In addition, this reduction in the fuel consumption also leads to a reduction in $CO_2$ emission. Diesel engines do not require spark-ignition systems, which makes them less technically complex. Thus, diesel engines are very suitable target engines for using biofuels with high cetane numbers. In this study, the spray characteristics of biofuels such as vegetable jatropha oil and soybean oil were analyzed and compared with those of diesel oil. The injection pressures and blend ratios of jatropha oil and diesel oil (BD3, BD5, and BD20) were used as the main parameters. The injection pressures were set to 500, 1000, 1500, and 1600 bar. The injection duration was set to $500{\mu}s$. Consequently, it was found that there is no significant difference in the characteristics of the spray behavior (spray angle) in response to changes in the blend ratio of the biodiesel or changes in the injection pressure. However, at higher injection pressures, the spray angle decreased slightly.

• Journal of Environmental Health Sciences
• /
• v.24 no.3
• /
• pp.92-98
• /
• 1998

작업장에서 근로자들이 엔진오일 등 각종 오일에 피부가 폭로되었을 때 이것을 쉽게 세척하기 위하여 일반적으로 솔벤트를 사용한다. 그러나 솔벤트를 사용하면 피부를 건조하게 만들 뿐만 아니라 오일에 함유되어 있는 각종 성분들을 피부내에 흡수되는 것을 촉진시킬 수 있어서 이에대한 대처방법이 요구된다. 특히 폐가솔닐엔진오일데는 방향족탄화수소(PAHs)와 같은 물질이 함유되어 있어 체내에 흡수되면 발암물질로 대사되어 표적장기(피부와 폐조직)에서 DNA adducts를 높은 수준으로 형성한다고 알려져 있다. 본 연구에서는 식물기름에서 구할 수 있는 d-라이모닌(Limonene)를 세척제로 사용하여 폐가솔린엔진오일의 폭로로 인하여 형성되는 DNA adducts를 $^{32}P-postlabeling방법으로 분석함으로써 d-라이모닌의 세척효과를 평가하고자 하였다. HDC(ICR) Br 자성마우스의 견갑골 부위에 있는 털을 제거하고 그 부위에 폐가솔린엔진오일을 폭로시키고 1시간과 8시간이 지난 다음에 d-라이모닌으로 각각 세척을 하였다. 마지막 폭로를 마치고 24시간이 지난 다음에 실험동물을 희생시켜 표적장기(폭로된 피부와 폐)에서 시료를 채취하였다. 먼저 시료에서 DNA를 분리하여 가수분해한 다음에 $^{32}P-postlabeling하여 DNA adducts를 분리하였다. 폐가솔린엔진오일만 폭로시킨 그룹의 피부와 폐조직에 형성된 DNA adducts가 각각 30.3$\pm$3.7과 15.7$\pm$2.4로서 대조군(2.5$\pm$1.0과 1.4$\pm$0.4)에 비하여 통계적으로 유의하게 높았고 (p<0.01), 또한 폐조직에서 보다 피부조직에서 통계적으로 유의하게 높았다(p<0.01). 폐가솔린엔진오일을 폭로시킨 후에 d-라이모닌으로 세척한 그룹에서는 피부와 폐조직에 형성된 DNA adducts가 통계적으로 유의하게 감소하였는데(p<0.01), 8시간 보다는 1시간이 지난 다음에 세척한 그룹에서 DNA adducts의 감소현상이 더 크게 나타났다. 결론적으로 피부에 폭로된 폐가솔린 엔진오일을 d-라이모닌으로 세척하면 폐가솔닐엔진오일내에 함유된 발암물질이 체내흡수되는 것이 억제되고, 피부와 폐조직 모두에서 DNA adducts의 형성을 감소시킬 수 있으며, 폐오일이 폭로된 후 빨리 세척하는 것이 더 효과적임을 증명하였다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.45 no.2
• /
• pp.114-121
• /
• 2009

There are increased in using the bio-ethanol, as the carbon neutral attracts many researchers due to a reduction in carbon dioxide spotted as the global warming gas. A gasoline engine with 100% of the bioethanol was developed and used in Brazil already, but researches of using the bio-ethanol in diesel engines are lack. In this study, combustion tests with blend fuel of the gas oil and bio ethanol by 50% maximally due to a low cetane number of bio-ethanol were accomplished as a basic study of introduction of using the bioethanol in diesel engines. The result was that smoke emission was decreased with increase in proportion of the bio-ethanol, due to the increase of a amount of pre-mixed combustion with ignition delay. Although the amount of $CO_2$ is reduced according as the bio-ethanol is used(carbon neutral), the emission of $CO_2$ with increase in the proportion of the bio-ethanol was more increased due to lower a heat value of bio-ethanol than gas oil.

• Analytical Science and Technology
• /
• v.27 no.1
• /
• pp.41-59
• /
• 2014

The aims of this work were the identification and the classification of fresh lubricants and used engine oils of vehicles for the application in forensic science field-80 kinds of fresh lubricants were purchased and 86 kinds of used engine oils were sampled from 24 kinds of diesel and gasoline vehicles with different driving conditions. The sample of lubricants and used engine oils were analyzed by GC/MS. The Bayesian model technique was developed for classification or identification. Both the wavelet fitting and the principal component analysis (PCA) techniques as a data dimension reduction were applied. In fresh lubricants classification, the rates of matching by Bayesian model technique with wavelet fitting and PCA were 97.5% and 96.7%, respectively. The Bayesian model technique with wavelet fitting was better to classify lubricants than it with PCA based on dimension reduction. And we selected the Bayesian model technique with wavelet fitting for classification of lubricants. The other experiment was the analysis of used engine oils which were collected from vehicles with the several mileage up to 5,000 km after replacing engine oil. The eighty six kinds of used engine oil sample with the mileage were collected. In vehicle classification (total 24 classes), the rate of matching by Bayesian model with wavelet fitting was 86.4%. However, in the vehicle's fuel type classification (whether it is gasoline vehicle or diesel vehicle, only total 2 classes), the rate of matching was 99.6%. In the used engine oil brands classification (total 6 classes), the rate of matching was 97.3%.

• Applied Chemistry for Engineering
• /
• v.17 no.1
• /
• pp.82-86
• /
• 2006

When a domestically manufactured floater is used in a general gasoline or LPG car, or a flowmeter is floated long time in the engine oil under above $150^{\circ}C$, the floater will be swelled or its organization will be slackened because weight and volume will be changed due to the osmosis of fuel. In this study, we conducted a research on a manufacturing technique of a foam-floater with the small changse in weight and volume, oil-resistance, and thermal resistance in the high temperature engine oil. When the prepared floater TROF II-3, where Nitrile Butadiene Rubber (NBR) as basic material of the floater was superseded by Hydrogenated Nitrile Butadiene Rubber (HNBR), was floated for 100 h at the engine oil of high temperature ($150^{\circ}C$), the change rates of the weight and the volume were 2.90%, and 2.56%, respectively. These were less than the NBR (TROF I-3) case, where the change rates of the weight and the volume were 10.81% and 3.08%, respectively, Therefore, TROF II-3 was determined to be suitable as an engine-oil floater in high temperature because the change of weight and volume were small, the appearance, and the specific gravity of floater were maintained uniformly in the high temperature.