• Journal of computational fluids engineering
• /
• v.17 no.3
• /
• pp.18-24
• /
• 2012

The aerodynamic performance of the pantograph on a high speed train was compared for different pantograph covers which are designed to block the aero-acoustic noise from the pantograph. For the study, two types of cover are designed: wedge and cone types. The lift force of pantograph with cover was compared with the force of pantograph only. The comparison clarified that the cone type cover increases the sideslip angle of the flow and decreases the lift force considerably. However, the wedge type cover changes the flow direction upward and increases the lift force of the pan head. This increment of lift force compensates the decrement of lift force caused by the blocking of the flow into the pantograph lower frame due to cover. Therefore, in case of the wedge type cover, the overall lift force changes slightly compared with the cone type cover.

• Korea-Australia Rheology Journal
• /
• v.20 no.4
• /
• pp.253-260
• /
• 2008

A method based on transient shear flow dynamics of red cell aggregates was developed to investigate reversible re-aggregation processes with decreasing shear flow. In the microchannel-flow aggregometry, the aggregated red blood cells that are subjected to continuously decreasing shear stress in microchannel flow were measured with the use of a laser-scattering technique. Both the laser-backscattered intensity and pressure were simultaneously measured with respect to time, resulting in shear stress ranging from $0{\sim}35\;Pa$ for a time period of less than 30 seconds. The time dependent recording of the backscattered light intensity (syllectogram) yielded an upward convex curve with a peak point, which reflected the transition threshold of aggregation in the RBC suspensions. Critical-time and critical-shear stress corresponding to the peak point were examined by varying the initial pressure-differential and the micro channel depth, and these results showed good potential for being used as new aggregation indices. In the present study, these newly proposed indices were also validated by differentiating the effect of fibrinogen on RBC aggregation and then these indices were compared to the conventional indices that were measured by a rotational aggregometer.

• Journal of the Korea Safety Management & Science
• /
• v.15 no.2
• /
• pp.63-69
• /
• 2013

The purposes of this study are to survey stereotypes of control-display relationships for seven principal controls in passenger cars using the paper-pencil and hardware tests, and to examine stereotype strength of the paper-pencil test through comparing the stereotypes for the controls derived by the two methods. Ninety two and 60 college-aged students participated in the paper-pencil test and the real car simulation of the hardware test, respectively. There are dominant motion-directions for all controls in the paper-pencil test, while in the hardware test, there are dominant motion-directions for six controls including head light, high beam, door window, ignition key, door key and door lock controls. The stereotypes of motion-directions for six controls obtained by the paper-pencil test were the same as or similar to those by the hardware test. It was inferred from this that the congruence of the stereotypes by the two methods might be attributed to two simple motion-direction principles of 'clockwise for increase' and 'upward for increase.' Although it is known that the hardware test would be best for obtaining accurate stereotypes between controls and displays, this study implies that if the paper-pencil test is well designed, the paper-pencil test can produce the same results as the hardware test at low cost and without consuming time.

• Water for future
• /
• v.27 no.1
• /
• pp.101-109
• /
• 1994

Characteristics of the vortex structure and the secondary scour at downstream part of the hydraulic structure such as drainage sluice or spillway ere studied. Mean shear velocity in the scour hole could be derived by the theory of energy conservation and the amount of a vortex erosion could be obtained using entrainment equation for given value of a shear velocity. Comparison of erosion rates with others showed a large value at low shear velocity due to the continuous and strong upward flow of the macroturbulence different from the conventional vortex formed in the lee-side of a sand ripple. For a design purpose, if the flow depth at the end of an apron and the properties of bed material are given, the amount of vortex erosion can be known.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.9
• /
• pp.2089-2104
• /
• 1995

A novel and efficient cutter path planning method for machining intricately shaped curved surfaces, called the steepest directed tree method, is presented. The curved surface is defined by triangular facets, the density and structure of which are determined by the intricacy and form accuracy of the surface. Geometrical form definition and recognition of the topological features are used to connect the nodes of the triangulated surface meshes for the successive and interconnected steepest pathways, which makes good use of end milling characteristics. The planetary cutter centers are determined to locate along smoothly changing paths and then the height values of the cutter are adjusted to avoid surface interference. Several machined examples of intersecting and intricate surfaces are presented to illustrate the benefits of the new approach. It is shown that due to more consistent geometry matching between cutter and surface(in comparison with the current CC Cartesian method) surface finish can be typically improved. Moreover, the material in concave fillets which is difficult to be removed by ball mills can be removed efficiently. The built-in positioning of cutter to avoid interference runs minutely in the sharp and discontinuous regions. The steepest upward movement of the cutter gives a stable dynamic cutting state and allows increase in the feedrate and spindle speed while remaining the stable cutting state.

• Nuclear Engineering and Technology
• /
• v.40 no.2
• /
• pp.155-162
• /
• 2008

Heat transfer experiments in an annulus passage were performed using SPHINX(Supercritical Pressure Heat Transfer Investigation for NeXt Generation), which was constructed at KAERI(Korea Atomic Energy Research Institute), to investigate the heat transfer behaviors of supercritical $CO_{2}$. $CO_{2}$ was selected as the working fluid to utilize its low critical pressure and temperature when compared with water. The mass flux was in the range of 400 to 1200 $kg/m^{2}s$ and the heat flux was chosen at rates up to 150 $kW/m^{2}$. The selected pressures were 7.75 and 8.12 MPa. At lower mass fluxes, heat transfer deterioration occurs if the heat flux increases beyond a certain value. Comparison with the tube test results showed that the degree of heat transfer deterioration in the heat flux was smaller than that in the tube. In addition, the Nusselt number correlation for a normal heat transfer mode is presented.

• Solar Energy
• /
• v.19 no.4
• /
• pp.33-43
• /
• 1999

The study on ice thermal storage system is to improve total system performance and increase the economical efficiency in actual all-conditioning facilities. To obtain the high charging and discharging efficiencies in ice thermal storage system, the improvement of thermal stratification is essential, therefore the process flow must be piston flow in the cylindrical type. With the relation of the aspect ratio(H/D) in the storage tank, the stratification is formed better as inlet flow rate is smaller. If the inlet and the outlet port are settled at the upside and downside of the storage tank, higher storage rate could be obtainable. In case that the flow directions inside the thermal storage tank are the upward flow in charging and the downward in discharging, thermal stratification is improved because the thermocline thickness is maitained thin and the degree of stratification increases respectively. In the charging process, in case of inlet flow rate the thermal stratification has a tendency to be improved with the lower flow rate and smaller temperature gradient in case of inlet temperature, the large temperature difference between inflowing water and storage water are influenced from the thermal conduction. The effect of the reference temperature difference is seen differently in comparison with the former study for chilled and hot water. In the discharging process, the thermal stratification is improved by the effect of the thermal stratification of the charging process.

• Journal of Biosystems Engineering
• /
• v.35 no.6
• /
• pp.426-433
• /
• 2010

This study was conducted to develop a pull-type sprayer which performs the safe spraying with improved ergonomic postures while pesticide spraying of roses in floricultural facilities. The performance of the ergonomically designed sprayer was analyzed with a comparison of a conventional spray method. The pull-type sprayer, consisting of power pump, hose and nozzle parts was designed to manually pull and spray to upward and horizontal directions. From the analysis of postures with the RULA method, the labor load to arm and wrist using the pull-type sprayer was less than that with conventional power sprayer, so that the intensity of labor reduces. Working capacity with pull-type sprayer was two-fold greater than the conventional power sprayer. After performing pesticide spraying with the pull-type sprayer, the operating cost was reduced to \585,000/yr, which is 79% less than that of cost (\2,197,500/yr) for using conventional power sprayer.

• International conference on construction engineering and project management
• /
• 2015.10a
• /
• pp.728-729
• /
• 2015

As environmental issues have been increased globally, eco-friendliness in the construction area, which accounts for more than 30% of total GHG gas emission has being urged. In response, the Korean government has implemented G-SEED(Green Standard for Energy and Environmental Design) certification from 2002. However, total number of certified apartment buildings is only around 1% of total number of approved apartment buildings. As a basic research to find out reasons of low rate of the certification, this paper analyzes consumers' decision-making process in G-SEED certified apartment building market comparing to non G-SEED certified one and draw System Dynamics modeling based on causal relationship. As a result, consumers' demand for the certified one is increased by 'Perceived Relative Utility' which is resulted from comparison process with non-certified one. The 'Perceived Relative Utility' is ascended upward steadily by 'Relative Perceived Price' considered as relatively short-term effect and 'Favorable Image of Certified Housing' referred to long-term effect.

• Geomechanics and Engineering
• /
• v.37 no.2
• /
• pp.97-107
• /
• 2024

The accurate prediction of grouting upward diffusion height is crucial for estimating the bearing capacity of tip-grouted piles. Borehole construction during the installation of bored piles induces soil unloading, resulting in both radial stress loss in the surrounding soil and an impact on grouting fluid diffusion. In this study, a modified model is developed for predicting grout diffusion height. This model incorporates the classical rheological equation of power-law cement grout and the cavity reverse expansion model to account for different degrees of unloading. A series of single-pile tip grouting and static load tests are conducted with varying initial grouting pressures. The test results demonstrate a significant effect of vertical grout diffusion on improving pile lateral friction resistance and bearing capacity. Increasing the grouting pressure leads to an increase in the vertical height of the grout. A comparison between the predicted values using the proposed model and the actual measured results reveals a model error ranging from -12.3% to 8.0%. Parametric analysis shows that grout diffusion height increases with an increase in the degree of unloading, with a more pronounced effect observed at higher grouting pressures. Two case studies are presented to verify the applicability of the proposed model. Field measurements of grout diffusion height correspond to unloading ratios of 0.68 and 0.71, respectively, as predicted by the model. Neglecting the unloading effect would result in a conservative estimate.