• Transactions of Materials Processing
• /
• v.11 no.2
• /
• pp.138-146
• /
• 2002

This paper is concerned with the simulation-based process design method involved non-steady state problem of tension levelling considering the elasto-plastic hardening behavior of a metallic strip by a commercial code ABAQUS/Standard. The tension levelling process is peformed to elongate the strip plastically in combination of tensile and bending strain by a controlled manner so that all longitudinal fibers in the strip have an approximately equal amount of length and undesirable strip shapes are corrected to the flat share. Objectives of this paper are the development of a general method for the design of a tension leveller by a finite element method and parameter studies for the deisgn variables such as the applied tension, the roll intermash includes the determination of the steady state using the simple unit of the tension levelling line and the effect of the finite element mesh size on the amount and distribution of the strain calculated. The analysis provides the information about the intermesh effect on the amount and final shapes of the strip and distribution of the strain in order to determine the amount elongation for correction of the irregular share.

• Proceedings of the KIEE Conference
• /
• 2007.04c
• /
• pp.97-99
• /
• 2007

This paper presents a fuzzy logical control method to implement an on-line optimum efficiency control for Permanent Magnet Synchronous Motor. This method real-timely adjusts the output voltage of the inverter system to achieve the optimum running efficiency of the whole system. At first, the input power is calculated during the steady state in the process of efficiency optimizing. To exactly estimate the steady state of the system, this section needs check up the speed setting on timely. The second section is to calculate input power of dc-bus. The exact measurement of the voltage and current is the vital point to acquire the input power. The third section is the fuzzy logic control unit, which is the key of the whole drive system. Based on the change of input power of dc-bus and output voltage, the variable of output voltage is gained by the fuzzy logical unit. With the on-line optimizing. the whole system call fulfill the minimum input power of dc-bus on the running state. The experimental result proves that the system applied the adjustable V/f control method and the efficiency-optimizing unit possesses optimum efficiency, and it is a better choice for simple variable speed applications such as fans and pump.

• Proceedings of the Korean System Dynamics Society
• /
• 1999.08a
• /
• pp.105-132
• /
• 1999

If a system such as a port has a large boundary and complexity, and the system's substance is considered as a black box, forecast accuracy will be very low. Furthermore various components in a port exert significant influence on each other. To copy with these problem the form of structure models were introduced by using SD method. The Competitive Ports Model had several sub-systems consisting of each Unit Port models, and each Unit Port model was made by quantitative, qualitative factors and their feedback loops. The fact that all components of one port have influence on the components of the other ports should be taken into account to construct Competitive Port Models. However, with the current approach that is impossible, and in this paper, therefore, models were simplified by HFP adapted to integrate level variables of unit port models. Although many studies on modelling of port competitive situation have been conducted, both theoretical frame and methodology are still very weak. In this study, a new algorithm called ESD(Extensional System Dynamics) for the evaluation of port competition was presented, and applied to simulate port systems in northeast Asia.

• Journal of Korean Biological Nursing Science
• /
• v.13 no.3
• /
• pp.204-210
• /
• 2011

Purpose: The purpose of this study was to provide basic data for the guidelines for cleaning the feeding bags by comparing the level of contamination according to cleaning and disinfection methods when feeding tube of Neurosurgery Intensive Care Unit patients. Methods: This study was a true-experimental study, with 48 cases in total. The feeding bag of 48 patients were randomly assigned to detergent cleaning method or disinfectant decontamination method. The period of the experiment was January to July 2008, and enteral nutrition was given within 30 minutes for 2 hours, 4 times a day at 7AM, noon, 5PM, and 9PM for seven days. Feeding bags were cleaned after each feeding according to the assigned cleaning and disinfection method followed by microbial cultures on 4th and 8th day before the 7AM feeding. Results: After three and seven days of feeding and cleaning, the level of contamination was significantly lower when bags were cleaned with disinfectant than cleaning with detergent and tepid water. Conclusion: In cases where feeding bags are reused, for example, intensive care unit and home care settings, study findings indicate that cleaning bags with disinfectant is an effective way to prevent contamination of bags.

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.3
• /
• pp.225-231
• /
• 2016

Peak load rate(i.e., maximum daily flow/average daily flow) has not been considered for industrial water demand planning in Korea to date, while area unit method based on average daily flow has been applied to decide capacity of industrial water treatment plants(WTPs). Designers of industrial WTPs has assumed that peak load would not exist if operation rate of factories in industrial sites were close to 100%. However, peak load rates were calculated as 1.10~2.53 based on daily water flow from 2009 to 2014 for 9 industrial WTPs which have been operated more than 9 years(9-38 years). Furthermore, average operation rates of 9 industrial WTPs was less than 70% which means current area unit method has tendency to overestimate water demand. Therefore, it is not reasonable to consider peak load for the calculation of water demand under current area unit method application to prevent overestimation. However, for the precise future industrial water demand calculation more precise data gathering for average daily flow and consideration of peak load rate are recommended.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.56 no.6
• /
• pp.103-111
• /
• 2014

This study was to develop the flood analysis module (FAM) for implementation of a web-based real-time agricultural flood management system. The FAM was developed to apply for an individual watershed, including agricultural reservoir. This module calculates the flood inflow hydrograph to the reservoir using effective rainfall by NRCS-CN method and unit hydrograph calculated by Clark, SCS, and Nakayasu synthetic unit hydrograph methods, and then perform the reservoir routing by modified Puls method. It was programmed to consider the automatic reservoir operation method (AutoROM) based on flood control water level of reservoir. For a $15.7km^2$ Gyeryong watershed including $472{\times}10^4m^3$ agricultural reservoir, rainfall loss, rainfall excess, peak inflow, total inflow, maximum discharge, and maximum water level for each duration time were compared between the FAM and HEC-HMS (applied SCS and Clark unit hydrograph methods). The FAM results showed entirely consistent for all components with simulated results by HEC-HMS. It means that the applied methods to the FAM were implemented properly.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.11
• /
• pp.853-858
• /
• 2006

In this paper, we propose a practical method for hardware-accelerated rendering of the depth image-based representation(DIBR) of 3D graphic object using graphic processing unit(GPU). The proposed method overcomes the drawbacks of the conventional rendering, i.e. it is slow since it is hardly assisted by graphics hardware and surface lighting is static. Utilizing the new features of modem GPU and programmable shader support, we develop an efficient hardware-accelerating rendering algorithm of depth image-based 3D object. Surface rendering in response of varying illumination is performed inside the vertex shader while adaptive point splatting is performed inside the fragment shader. Experimental results show that the rendering speed increases considerably compared with the software-based rendering and the conventional OpenGL-based rendering method.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.35 no.4
• /
• pp.16-23
• /
• 2012

At present, the significance of a new manufacturing system that can shift from 'mass production' and consider life cycles of a product is pointed out and extremely expected. In such a situation, it is recognized that the modular design, often called 'unit design,' is the important design methodology which realizes the new production system enabling 'cost reduction,' 'flexible production of a multi-functional artifact,' 'settlement of an environmental issue,' and so on. A module (unit) of a product is generally defined as 'the parts group made into the sub-system from a certain specific viewpoint.' So far, there have been many researches related to the modular design. However, they are often limited to a certain viewpoint (objective). This paper proposes a simple but effective method for multi-objective modular design. In the proposed method, a new design metric, called similarity index, is proposed to evaluate the modular design candidates from the multiple viewpoints.

• Journal of the Korean housing association
• /
• v.22 no.3
• /
• pp.101-111
• /
• 2011

This study was conducted to investigate the indiscriminate development occuring as a result of high-density land use per lot in residential areas of Seoul, which mainly consist of detached houses. The primary goals of this study were: (1) to suggest a block unit development method as an alternative architectural method of the current uniform development, in which high-rise and high-density apartments are usually built; and (2) to check the feasibility of the suggested method. Based on the analyses of the existing block composition types of residential areas, the prerequisite planning indices for applying a collective housing model were investigated. Subsequent to applying a collective housing type within each unit block, the collective housing model was analyzed. The results of the analyses showed that indiscriminate development was rampant in detached urban houses areas, and more than 70% of the buildings constructed before the 1980s needed re-development. The feasibility of the models was investigated depending on the models of low-rise and high-density collective housing, which utilize various block arrangements such as the court type, linear type, villa type, and composite type. The results of this study showed that the newly applied low-rise and highdensity multiple dwelling housing model in urban individual residential area significantly contributed to creating a good living environment in terms of both physical and psychological aspects.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.5
• /
• pp.592-598
• /
• 2007

The fuel charge is getting higher in navigation cost. Therefore, shipowners try to find the method for reducing oil consumption. ESS(Energy Saving System) is one of he method. ESS is the system consisted with two inverters, ESS control unit and monitoring system. Two inverters control two main sea water cooling pumps. In the ESS control Unit, the control algorithm finds optimized point to decrease a power consumption of main sea water cooling pumps. Monitoring system observes ESS not to work improperly. ESS is experimented in the laboratory with real condition and analyzed in every view. After experiment, the result of the experiment shows that the control algorithm works correctly and safely. ESS has a plan to be operated in the ship soon. In that case, additional devices are needed to connect ESS with cooling system of the vessel. So the development of addition device is needed and being studied.