• ETRI Journal
• /
• v.32 no.5
• /
• pp.740-749
• /
• 2010

In a machine translation system, word sense disambiguation has an essential role in the proper translation of words when the target word can be translated differently depending on the context. Previous research on sense identification has mostly focused on adjacent words as context information. Therefore, in the case of nominal compounds, sense tagging of unit nouns mainly depended on other nouns surrounding the target word. In this paper, we present a practical method for the sense tagging of Korean unit nouns in a nominal compound. To overcome the weakness of traditional methods regarding the data sparseness problem, the proposed method adopts complement-predicate relation knowledge that was constructed for machine translation systems. Our method is based on a sentential form recovery technique, which recognizes grammatical relationships between unit nouns. This technique makes use of the characteristics of Korean predicative nouns. To show that our method is effective on text in general domains, the experiments were performed on a test set randomly extracted from article titles in various newspaper sections.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.47-54
• /
• 2002

A barrel cam is used as a very important part of an index drive unit. The index drive unit must have an intermittent-rotational motion. The barrel typed cam and roller gear mechanism has the advantages of high reliability to perform a prescribed motion of a follower. This paper proposes a new method for the shape design of the barrel cam and also a CAD program is developed by using the proposed method. As defined in this paper, the relative velocity method for the shape design calculates the relative velocity of the follower versus cam at a center of roller, and then determines a contact point by using the geometric relationships and the kinematic constraints, where the direction of the relative velocity must be parallel to a common tangential line at the contact point of two independent bodies, i.e. the cam and the follower Then, the shape of the cam is defined by the coordinate transformation of the trace of the contact points. This paper presents two examples for the shape design of the barrel cam in order to prove the accuracy of the proposed methods.

• Nuclear Engineering and Technology
• /
• v.46 no.3
• /
• pp.291-298
• /
• 2014

This paper concerns estimating uncertainties of the core neutronics design parameters of power reactors by direct sampling method (DSM) calculations based on the two-step McCARD/MASTER design system in which McCARD is used to generate the fuel assembly (FA) homogenized few group constants (FGCs) while MASTER is used to conduct the core neutronics design computation. It presents an extended application of the uncertainty propagation analysis method originally designed for uncertainty quantification of the FA FGCs as a way to produce the covariances between the FGCs of any pair of FAs comprising the core, or the covariance matrix of the FA FGCs required for random sampling of the FA FGCs input sets into direct sampling core calculations by MASTER. For illustrative purposes, the uncertainties of core design parameters such as the effective multiplication factor ($k_{eff}$), normalized FA power densities, power peaking factors, etc. for the beginning of life (BOL) core of Yonggwang nuclear unit 4 (YGN4) at the hot zero power and all rods out are estimated by the McCARD/MASTER-based DSM computations. The results are compared with those from the uncertainty propagation analysis method based on the McCARD-predicted sensitivity coefficients of nuclear design parameters and the cross section covariance data.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.2 no.2
• /
• pp.1-7
• /
• 2005

For the reliability evaluation of the track drive unit(TDU), firstly, we analyzed the major failure modes through FMEA(failure mode & effects analysis), FTA(failure tree analysis), and 2-stage QFD(quality function deployment), and then quantitatively determined the priority order of test items. The Minitab analysis was also performed for prediction of life distribution and parameters of TDU by use of field failure data collected from 430 excavators for two years. In addition, we converted the fluctuation load in field conditions into the equivalent load, and for evaluation of the accelerated lift by the cumulative fatigues, the equivalent load is again divided into the fluctuation load by reference of test time. And then, by use of the test method in this paper, the acceleration factor(AF) of needle bearing inside planetary gear which is the most weakly designed part of TDU is achieved as 5.3. This paper presents the quantitative selection method of test items for reliability evaluation, the determination method of the accelerated life test time, and the method of non-failure test time based on a few of samples. And, we proved the propriety of the proposed methods by experiments using a TDU for a 30 ton excavator.

• Journal of the Korean Society of Safety
• /
• v.10 no.3
• /
• pp.30-41
• /
• 1995

This paper proposed a simple method for measuring surface roughness of ground surface. Utilizing non-contact in-process measuring system using the diode laser. The measurement system is consisted of a laser unit with a diode laser and a cylindrical lens, a detecting unit with polygon mirror and CCD array sensor, and a signal processing unit with a computer and device. During operation, this measuring system can provide information on surface roughness in the measuring distance with a single sampling and simultaniously monitor the state of the grind wheel. The experimental results, showed that the Increase of the feed rate and the dressing speed an caused increase in the surface roughness and when the surface roughness is 4Rmax-10Rmax, the cutting speed is 1653m/min-1665m/min, the table speed is 0.2n1/min -0.9m/min, the dressing speed is 0.2mm/rev～0.4mm/rev, the stylus method and the in-process method can be obtained the same results. Thus, under limited working conditions, using the proposed system, the surface roughness of the ground surface during cylindrical grinding can be obtained through the in-process measurement method using the diode laser.

• Korean Journal of Food Science and Technology
• /
• v.34 no.3
• /
• pp.380-384
• /
• 2002

For the screening of gamma-irradiated grains, domestic rice, glutinous rice, barley, and wheat were irradiated with 0.1, 0.3, 0.5, 0.7, and 1.0 kGy and screened using the DEFT/APC (Direct Epifluorescent Filter Technique/Aerobic Plate Count) method. The log DEFT/APT units increased with the dose increment in all samples, whereas the log APC unit decreased gradually. For rice, barley, and wheat, unirradiated and irradiated samples with below 0.3 kGy had 2.0 or lower logarithmic units, whereas those with 0.5 kGy or higher had 2.0 or higher logarithmic units. For glutinous rice, the sample irradiated with 0.5 kGy showed 1.92 logarithmic unit and those with 0.7 kGy or higher had 2.0 or higher logarithmic units. These results suggest that if the grains show 2.0 or higher logarithmic units, they could be assumed to have been irradiated at a dose level of at least 0.5 kGy. In conclusion, grains could be easily screened through the DEFT/APC method.

• Journal of Technologic Dentistry
• /
• v.41 no.1
• /
• pp.9-19
• /
• 2019

Purpose: This study was conducted to comparative evaluate the marginal and internal gap of three-unit metal frameworks(Co-Cr) fabricated by wax milling method and digital light projection method of CAD/CAM systems. Methods: All the specimens were fabricated by three different fabrication methods: conventional wax up with casting(CWC), milled wax block with casting(MWC), digital light projection with casting(DLPC) (n=10 each). The marginal and internal fits of specimens were examined using a replica technique. The light-body silicone thickness was measured at 8 reference points(each abutment: 16 measurements). All measurements were conducted by a stereomicroscope. Digital photo were taken at $150{\times}$ magnification and then analyzed using a measurement software. The Mann-Whitney test was used for analyzing the results. Results: Statistically significant differences were found between the fabrication methods(p<0.001). The mean(SD) is ${\mu}m$ for fabrication methods, the mean marginal fit were recorded respectively, CWC 63(38), MWC group 50(33), DLPC 103(54) and the mean internal fit CWC 96(47), MWC group 116(41), DLPC 138(66). Conclusion : The marginal and internal fit were statistically different according to the fabrication methods(p<0.001). In all fabrication methods, the greatest misfit was found the occlusal area of all specimens.

• Composites Research
• /
• v.34 no.1
• /
• pp.30-34
• /
• 2021

This paper present a three-dimensional unit cell finite element analysis to predict the pull-out behavior of a single stitch in a composite laminate. The stitching process used for this study correspond to the I-fiber stitching method that has been studied by the Composite Structures Lab (CSL) as a new through-thickness reinforced method. A total of six cases were analyzed, which were divided in two groups by the stitching yarn used, 6k and 12k. Each group of cases have three different thickness according to the amount of plies; 16 plies, 32 plies and 64 plies. The finite element analysis used the cohesive zone method to characterize the single stitch reinforcement in the interface. Due to the complexity of the load vs displacement curves taken from the experimental results, a bilinear and trilinear bridging laws were implemented in the models. The cohesive parameters used for each case showed a good agreement with the experimental data and can be used for future studies.

• The Korean Journal of Applied Statistics
• /
• v.34 no.2
• /
• pp.205-223
• /
• 2021

In this paper, we study a method to determine the existence of unit roots by using the adaptive lasso. The previously proposed method that applied the adaptive lasso to the original time series has low power when there is an unknown trend. Therefore, we propose a modified version that fits the ADF regression model without deterministic component using the adaptive lasso to the detrended series instead of the original series. Our Monte Carlo simulation experiments show that the modified method improves the power over the original method and works well in large samples.

• KIEAE Journal
• /
• v.4 no.3
• /
• pp.45-52
• /
• 2004

The purpose of this research was to identify the structural characteristics of open housing typologically and systematically. The main method of this study was content analysis and literature review on open housing. This study found that the typological analysis on terminology and the details of the constituents concerning structural patterns in open housing indicated that the main approaches were classified into three criteria such as 'Organization Element', 'Construction Element', and 'Equipment Element'. Organization Element was classified into 'Main Dwelling Unit Area and its Form', 'Room Organization Method', 'Relationship with the Main Dwelling Unit's External Constituents', and 'Combination Method of Support and Infill'. Construction Element was classified into 'Method of Structure' and 'Structural Element Technology'. Equipment Element was classified into 'Method of Using Duct' and 'Wet Zone Method'. The attributes were determined based on these classifications. The results of this study can be used to construct an evaluation tool and further to develop a framework in understanding open housing. Technical research should be conducted on the variables that affect the flexibility of space.