• 문화기술의 융합
• /
• 제9권5호
• /
• pp.529-534
• /
• 2023

고속 및 대면적 인쇄를 위한 라인 프린팅 기술은 늘어난 헤드 길이만큼 헤드 내부로 잉크를 공급하는 유로를 확보해야 하는 구조적 취약점과 제조 과정에서 발생하는 잔류응력에 의한 피드홀 변형으로 인해 노즐층이 파손되거나 잉크가 누출되는 결함이 있다. 따라서 본 논문에서는 견고하고 신뢰할 수 있으며 라인 프린팅 방식에 보다 적합한 열전사 방식의 잉크젯 프린트 헤드 형상을 제안하고자 한다. 먼저 실험을 통해 초기 라인 프린팅 헤드의 변형량을 측정한 후 이를 등가의 하중량으로 변환하였으며 FEA 해석을 통해 하중 추정 방법의 타당성을 검증하였다. 또한 헤드 크기를 증가시키지 않으면서 변형을 최소화할 수 있도록 기둥이나 지지벽으로 단위 노즐을 보강하거나 지지빔이나 건/습식각된 브릿지를 추가하여 내부 강성을 증가시킨 헤드 구조를 설계하였으며, 피드홀 변형이 최대 90% 감소하는 것을 확인하였다. 제안된 형상 중 공정 편의성과 제작비용을 고려하여 건식각된 피드홀 브릿지 형태의 헤드를 선정하였으며 실제 제작을 통해 노즐층 변형이나 잉크 누출 없이 정상 작동하는 것을 확인하였다.

• 한국환경생태학회지
• /
• 제29권6호
• /
• pp.936-946
• /
• 2015

본 연구는 도심의 열환경 개선 및 건물에너지저감 효과가 입증된 벽면녹화 중 기존 건물에 적용 가능한 패널형 벽면녹화 식재기반 유형에 따른 건물에너지 저감 성능을 분석하고자 하였다. 식재기반 유형은 총 4가지 유형으로 하였으며, Case A는 벽면녹화가 미적용된 유형으로 콘크리트 + 단열재로 구성하였다. Case B는 식재층 + 무기다공성블록 + 콘크리트 + 단열재로 구성하였으며, Case C는 식재층 + 코코피트블록 + 콘크리트 + 단열재로 구성하였다. Case D는 식재층 + 마사토블록 + 콘크리트 + 단열재로 구성하였다. 분석항목으로는 열전도율, 열관류율, 건물에너지시뮬레이션을 실시하였다. 식재기반 유형별 열전도율은 Case C(0.053W/mK) > Case B(0.1W/mK) > Case D(0.17W/mK)의 순이었다. 에너지시뮬레이션 결과 중 단위면적당 냉방피크부하저감은 미적용인 Case A 대비 Case C(1.19%) > Case B(1.14%) > Case D(1.01%)이며, 난방피크부하저감은 Case A 대비 Case C(2.38%) > Case B(1.82%) > case D(1.50%)로 산정되었다. 연간 냉 난방부하저감은 미적용 Case A대비 벽면녹화 유형에서 0.92~1.28% 저감률을 나타내었다. 연간 냉난방에너지사용량은 3.04~3.22%의 저감률을 보였으며, 1차에너지사용량은 Case A대비 나머지 유형에서 평균 5,844 kWh/yr의 저감량을 보였다. 연간 이산화탄소발생량은 벽면녹화 미적용 Case A대비 평균 996kg 저감량을 보였다. 식재위치별 에너지성능평가 결과 동향 > 서향 > 남향 > 북향 순이었다. 벽면녹화비율에 따른 에너지성능평가 결과 녹화 비율이 높아짐에 따라 양호한 결과를 나타내었으며, 20~80%의 비율보다 100% 녹화시 약 2배의 저감률을 보였다.

• 항공우주기술
• /
• 제4권2호
• /
• pp.7-14
• /
• 2005

본 논문은 군에서 운용중인 대공포 사격 훈련용으로 개발한 무인 표적기용 자동비행시스템 개발에 관한 논문이다. 조종사에 의해 수동으로 운용중인 표적기를 자동화함으로써 조종사 측면에서는 비행업무를 경감시키고, 군 측면에서는 사격훈련 예산절감이라는 장점을 가지게 된다. 현재까지 개발된 대부분의 UAV(Unmanned Aerial Vehicle)는 항공기 자세를 측정하기 위해 AHRS(Attitude & Heading Reference System)와 IMU(Inertial Measurement Unit)등의 고가의 센서를 장착하고 있지만 이를 장착하고 무인기를 사격훈련용으로 사용하기에는 비용절감이라는 목적에 적합하지 않다. 이에 본 논문은 저가의 센서를 장착하고 자동비행이 가능하도록 저가형 자동비행시스템을 개발하였으며, 비행시험을 통하여 자동비행시스템 성능을 입증하였다.

• 한국염색가공학회지
• /
• 제28권2호
• /
• pp.109-117
• /
• 2016

Synthetic fabrics, such as nylon and polyester, were dyed with persimmon juice by using a padding mangle repeatedly. The mechanical properties of these synthetic fabrics were analyzed using the Kawabata evaluation system. The following findings were obtained from this investigation. As the number of repetitions of padding dyeing increased, the tensile energy per unit area and the tensile resilience of synthetic fabric remained almost unchanged, whereas the linearity of the load-extension curve of the synthetic fabrics increased. As the number of padding repetitions increased, the synthetic fabrics dyed with persimmon juice exhibited increases in thickness and weight. As the number of repetitions of padding treatment with persimmon juice increased, the values of stiffness, anti-drape stiffness, fullness, and softness also increased, whereas the flexibility with soft feeling, crispness, and scrooping sensation significantly decreased. The amount of coated persimmon juice on the surface of the fabrics increased after three repetitions of padding treatment with persimmon juice. Nylon and polyester fabrics were dyed evenly with persimmon juice treated using a padding mangle.

• 한국환경과학회지
• /
• 제16권2호
• /
• pp.227-232
• /
• 2007

Water pollution in enclosed water bodies such as lake and river has become a serious problem over the world. Domestic wastewater is responsible for more than 60 % pollution load in public water area in Korea. Effluent of the treated domestic wastewater at low removal level is abundantly fed rivers and lakes and thus be an serious cause of lake pollution. Therefore, effective implement of domestic wastewater treatment in basin of lake and river must be prepared. The septic tank is one of the effective domestic wastewater treatment equipment and used in individual treatment for a unit of household, The purpose of septic tank as biological treatment system is simultaneously to remove BOD, T-N, T-P and reduce turbidity from influent. Accordingly, the appropriate control of functional microorganisms is important subject for the establishment of stability and economy of the biological treatment method. Especially, microanimals as a high-ranked microorganisms of food-chain are important, because microanimals control the other microorganisms especially various bacteria and effect on function of treatment. Therefore, it is necessary that functional predator like rotifers are attached in wastewater treatment process. In this study, the methods for attachment high density the rotifer to and improvement of transparency in the effluence by a dense rotifer was examined using laboratory scale biological treatment reactor simulated septic tank and real one.

• 대한기계학회논문집A
• /
• 제33권2호
• /
• pp.153-161
• /
• 2009

Three-dimensional finite-element methods(FEM) have been used to analyze the thermal stress of an exhaust gas recirculation(EGR) cooler due to thermal and pressure load. Since efficiency and capability of the heat exchanger are mainly dependent on net heat transferring area of the EGR cooler system, the tube inside the system has a numerous dimples on the surface. Thus for finite element analysis, firstly the dimple-typed tube is modeled as a plain element without the dimple, and then the equivalent thermal conductivities and elastic modulus are calculated. This work describes the numerical homogenization procedure of the dimple-typed tube and verifies the equivalent material properties by comparison of a single unit and the actual full model. Finally, the homogenization scheme presented in this study can be efficiently applied to finite element analyses for the thermal stress and deformation behavior of the EGR cooler system with the dimple-typed tube.

• 에너지공학
• /
• 제11권3호
• /
• pp.254-261
• /
• 2002

The fabrication method for the main components of the polymer electrolyte membrane fuel cell stack such as electrodes, membrane-electrode assemblies, and bipolar plates was established for the effective electrode area of 240 ㎠. A counter-flow type 100-cell stack was fabricated by using the above components and then a maximum power of 7.44 kW for H$_2$/O$_2$ and 5.56 kW for H$_2$/air could be obtained at 70$\^{C}$ and 1 atm. It was seen that the distribution of the OCV for unit cells in the stack was uniform but the voltage deviation increased as the load increased due to the IR drop and the electrode polarization. The stack was applied to the power source of the fuel cell/battery hybrid electric golf car. It produced about 1 kW at a room temperature operation during the test run, which occupied about 43% of the total power required by the 2.3 kW motor.

• Structural Engineering and Mechanics
• /
• 제23권6호
• /
• pp.635-649
• /
• 2006

The static and dynamic responses of guyed telecommunication towers can be determined by using two models, the space truss element model, and the equivalent beam-column element model. The equivalent beam-column analysis is based on the determination of the equivalent shear, torsion, and bending rigidities as well as the equivalent area of the guyed mast. In the literature, two methods are currently available to determine the equivalent properties of lattice structures, namely: the unit load method, and the energy approach. In this study, an equivalent beam-column analysis is introduced based on an equivalent thin plate approach for lattice structures. A finite-element modeling, using suitably modified ABAQUS software, is used to investigate the accuracy of utilizing the different proposed methods in determining the static and dynamic responses of a guyed tower of 364.5-meter high subjected to static and seismic loading conditions. The results from these analyses are compared to those obtained from a finite-element modeling of the actual structure using 3-D truss and beam elements. Good agreement is shown between the different proposed beam-column models, and the model of the actual structure. However, the proposed equivalent thin plate approach is simpler to apply than the other two approaches.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.707-710
• /
• 2002

A 120kV/70A high voltage switch has been installed at Korea Atomic Energy Research Institute in Taejon to supply power with Korea Superconducting Tokamak Advanced Research (KSTAR) Neutral Beam Injection (NBI) system. NBI system requires fast cutoff of the power supply voltage for protection of the grid when arc detected and fast turn-on the voltage for sustaining the beam current. Therefore the high voltage switch and arc current detection circuit are important part of the NBI power supply and there are much need for high voltage solid state switches in NBI system and a broad area of applications. This switch consisted of 100 series connected MOSFETs and adopted the proposed simple and reliable gate drive circuit without bias supply, Various results taken during the commissioning phase with a 100kW resistive load and NBI source are shown. This paper presents the detailed design of 120kV/70A high voltage MOSFETs switch and simple gate drive circuit. Problems with the high voltage switch and gate driver and solutions are also presented.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.565-575
• /
• 2009

A forklift (also called a lift truck) is a powered industrial truck that is used to lift and transport materials. It has become an indispensable piece of equipment in manufacturing and warehousing operations. The modem forklift is equipped with automatic transmission to meet the requirement of loading and easy operation of the vehicle. This paper proposes the design of TECU(Transmission Electronic Control Unit) which is applied to PSD322-Axle transmission. Garofalo's control technique is generally used to the automatic transmission. We consider the work quality and market requirement that does not want to control engine throttle. This paper proposes new controller system which guarantees efficient speed changes with simple system. This new system does not control the engine throttle spontaneously. But it has the load of engine and vehicle as a maximum disturbance. The scope of the disturbance is limited to the stoll area of the torque converter. This paper proposes a ideal control commander that converges relative velocity of the input and ouput of a clutch into a zero. We design linear controller to execute the idea control commander. We applied the control algorithm to the forklift of PSD322-Axle type and the performance of this controller was verified.