• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 한국지역지리학회지
• /
• 제3권2호
• /
• pp.37-87
• /
• 1997

만경강유역을 하나의 연장선상에 놓고 연구한 결과, 그 공간상에서 역사와 더불어 형성발달해온 시공연속체를 확인할 수 있었다. 만경강상류에서 하류 하구연안에 이르는 면장공간상에서의 개간과정은 여말에서 부터 시작되어 오늘에 이른 것으로 볼 수 있다. [기원지-지향지] 지향가설에서 본 개간과정에서 개간의 기원지는 만경강상류 산간계곡의 지류곡지 개간을 효시로 하여 기원지가 이루어지고, 조선조 중기까지는 수방대책의 발달과 더불어 하천 중류까지 진출하고, 하천 본류에 대한 하류지역의 계간은 하천의 규모와 유수량의 증가로 인한 하안의 홍수와 범람을 극복할 수 있는 인공제방을 축조할 수 있는 기술수준에 이른 1920년대에 들어서야 본격화되고, 그후 연이어 하구연안의 간석지 개간도 시행되어 개간의 개척첨단이 이들 지향지인 해안간석지일대에 형성되는 것을 볼 수 있다. 시간의 흐름과 더불어 각 시기마다 공간의 변화도 수반되어 시공연속체가 발달하는 것을 볼 수 있다. 취락의 경우 개간과정에 따라 산간계곡 산록일대에서는 주변입지적 집촌, 하천중류와 하류에서는 중앙입지적 집촌, 하천하구 간석지에서는 중앙입지적 열촌형태가 우세하게 나타났다.

• 한국산림과학회지
• /
• 제15권1호
• /
• pp.1-38
• /
• 1972

우리나라는 근래(近來) 고도경제성장(高度經濟成長)으로 인(因)하여 목재수요(木材需要)가 급증(急增)하고 있으나 국내생산재(國內生産材)가 공급율(供給率)은 수요량(需要量)의 20% 정도(程度)에 지나지 않아 많은 외재(外在)를 도입(導入)하고 있으므로 장래(將來)의 목재(木材) 수요공급(需要供給)의 균형(均衡)을 이룩하기 위하여 강력(强力)한 산림자원(山林資源) 조성사업(造成事業)의 추진(推進)이 요망(要望)된다. 산림자원(山林資源) 조성사업(造成事業)을 추진(推進)하는데 있어서 가장 중요(重要)한 것은 조림의욕(造林意慾)을 높이고 조림사업(造林事業)에 필요(必要)한 산업자본(産業資本)을 산림(山林)에 유치(誘致)하도록 하는 일인데, 이러한 역할(役割)을 할 수 있는 경제적시설(經濟的施設)의 하나가 산림보험제도(山林保險制度)의 실시(實施)인 것이다. 산림보험(山林保險)을 실시(實施)하면 산림재해(山林災害)가 보상(補償)되므로 자본가(資本家)는 안심(安心)하고 조림투자(造林投資)를 할 수 있을 뿐만 아니라 산림(山林)을 담보(擔保)로 한 금융(金融)의 길도 열리어 투자(投資)한 산림(山林)에 환금성(換金性)이 주어지므로 산업자본가(産業資本家)가 산림투자(山林投資)를 회피(回避)하지 않게 되어 산림자원(山林資源) 조성사업(造成事業)이 촉진(促進)될 수 있다. 이러한 관점(觀點)에서 외국(外國)에서는 19세기말(世紀末)부터 산림보험제도(山林保險制度)가 실시(實施)되기 시작(始作)하여 주요(主要) 임업선진국(林業先進國)에서는 모두 산림보험(山林保險)을 실시(實施)하고 있는 것이다. 산림보험(山林保險)을 실시(實施)하는데 있어서 가장 중요(重要)한 것은 장기간(長期間)에 걸친 산림재해(山林災害)의 통계자료(統計資料)를 정확(正確)히 조사(調査)하는 일과 그 나라의 여건(與件)에 맞는 산림보험제도(山林保險制度)를 창설(創設)하는 일이다. 과거(過去) 10년간(年間)(1961~1970)의 년평균(年平均) 산림재해상황(山林災害狀況)을 조사(調査)한 결과(結果)는 산림화재(山林火災)가 9,000여정보(餘町步), 곤충피해(昆蟲被害)가 570,000정보(町步), 병균피해(病菌被害)가 694정보(町步)로 나타났다. 특(特)히 그중 외국(外國)의 산림보험(山林保險)에서 재해보상(災害補償) 대상(對象)의 으뜸이 되고 있는 산림화재(山林火災) 피해상황(被害狀況)을 과거(過去) 18년간(年間)(1953~1970)에 걸쳐서 조사(調査)한 결과(結果)에 의하면 산화면적(山火面積) 위험율(危險率)이 $\frac{1.1853}{1,000}$였고 1960~1969년(年) 사이의 전국(全國) 산림화재면적(山林火災面積) 위험율(危險率)은 $\frac{1.3045}{1,000}$로서 유우럽에 비(比)하여 높았으나 일본(日本)에 비(比)하여 그리 높지 않았다. 또 과거(過去) 5년간(年間)(1966~1970)의 전국(全國)의 산화재적(山火材積) 위험율(危險率)은 $\frac{0.1991}{1,000}$로서 대단(大端)히 낮은데 이것은 우리나라 산림(山林)의 축적(蓄積)이 빈약(貧弱)한데서 온 결과(結果)였다. 이러한 산림재해상황(山林災害狀況)에 비추어 우리나라에서 산림보험(山林保險)을 실시(實施)하려면 어떠한 내용(內容)의 산림보험제도(山林保險制度)를 설립(設立)하는 것이 좋겠는가 하는 질문조사(質問調査)의 결과(結果)는 다음과 같았다. 1. 산림보험(山林保險)의 필요성(必要性) 산림보험(山林保險)은 산림담보(山林擔保)에 의(依)한 금융(金融)의 길을 열어주고(5.65%), 산림피해(山林被害)를 당(當)하였을 때 재조림비(再造林費)를 확보(確保)하게 하여(35.87%), 조림투자(造林投資)를 보증(保證)하는 수단(手段)(46.74%)으로 반드시 실시(實施)되어야 한다고 응답(應答)하였다. 2. 산림보험법(山林保險法) 산림(山林)의 특수성(特殊性)에 비추어 일반(一般) 손해보험(損害保險) 규정(規程)을 준용(準用)할 것이 아니라(8.35%), 산림보험(山林保險)을 위한 특별볍(特別法)을 제정(制定)하여야 한다고 응답(應答)하였다(88.26%). 3. 보험경영업체(保險經營業體)의 종류(種類) 일반(一般) 보험회사(保險會社)(17.42%)나 산림소유자(山林所有者) 상호조합(相互組合)(23.53%)에서 산림보험(山林保險)을 취급(取扱)할 수도 있겠으나, 산림보험(山林保險)의 특이성(特異性)에 비추어 국(國) 공영산림보험(公營山林保險)의 별도(別途)로 운영(運營)되어야 한다고 반응(反應)하였다(56.18%). 4. 보험사고(保險事故)의 종류(種類) 산림보험(山林保險) 사고(事故)를 산화(山火)에 국한(局限)시키거나(23.38%), 산화(山火) 및 기상해(氣象害)만을 포함(包含)시키면 된다는 의견(意見)도 있으나(14.32%), 산림보험(山林保險) 사고(事故)에 산화(山火), 기상해(氣象害), 병충해(病蟲害)까지 포함(包含)시켜야 한다는 의견(意見)이 가장 많았다(60.68%). 5. 보험사고(保險事故) 취급대상(取扱對象)의 종류(種類) 산림보험(山林보험) 취급대상(取扱對象) 수종(樹種)은 침엽수(針葉樹) 인공림(人工林)에 한정(限定)시키거나(13.47%), 침엽수(針葉樹)와 활엽수(濶葉樹)의 인공림(人工林)만을 포함(包含)시키기를 원(願)하는 반응자(反應者)도 있었으나(23.74%), 많은 반응자(反應者)가 수종(樹種), 임종(林種)(인공(人工), 천연(天然)) 구별(區別)없이 모두 포함(包含)시켜야 된다고 반응(反應)하였다(61.64%). 6. 보험사고(保險事故) 취급대상(取扱對象)의 범위(範圍) 산림보험(山林保險) 사고(事故) 취급대상(取扱對象) 범위(範圍)는 10년(年) 이하(以下)의 유령림(幼齡林)만 취급(取扱)하기를 원(願)하는 자(者)(15.23%), 20년(年) 이하(以下)의 임목(林木)만을 대상(對象)으로 하면 족(足)하다는 반응자(反應者)가 있었으나(32.95%), 많은 반응자(反應者)가 40년생(年生) 이하(以下)의 임목(林木)까지 포함(包含)하기를 바라고 있었다(46.37%). 7. 보험계약(保險契約) 기간(期間) 산림보험(山林保險) 계약기간(契約期間)은 1년(年) 단위(單位)가 좋다는 자(者)도 상당(相當)히 있었으나(31.74%), 과반수(過半數)가 5년(年) 단위(單位)로 계약(契約)하는 것을 바라고 있었다(58.68%). 8. 보험계약(保險契約)의 제한(制限) 5정보(町步) 미만(未滿)의 소면적(小面積)은 산림보험(山林保險) 대상(對象)에서 제외(除外)하고(20.78%), 단위(單位) 면적당(面積當) 일정(一定) 재적(材積) 또는 주수(株數)를 보유(保有)하고 있는 산림(山林)만을 계약대상(契約對象)으로 하는 것이 좋다고 반응(反應)하였다(63.77%). 9. 계약방법(契約方法) 산림보험(山林保險) 계약방법(契約方法)은 임의(任意)로 산림(山林)을 선택(選擇)하여 계약(契約)하기를 원(願)하는 자(者)(32.13%), 임의(任意)로 계약(契約)하되 소유산림(所有山林) 전체(全體)를 일괄(一括) 계약(契約)하도록 하는 방법(方法)을 택(擇)하여야 한다는 자(者)(33.48%), 특정임지(特定林地)(신식지(新植地), 보조조림지(補助造林地), 고가임지(高價林地))는 의무적(義務的)으로 계약(契約)하도록 하여야 한다는 반응자(反應者)(31.92%)로 나타나 비슷한 반응(反應)을 보였다. 10. 보험료율(保險料率) 산림보험(山林保險) 요율(料率)은 지역(地域)에 따르는 위험정도(危險程度)를 참작(參酌)하여 면적비례(面積比例)로 결정(決定)하여야 한다는 의견(意見)(31.59%)과 지역(地域) 위험율(危險率)을 참작(參酌)하여 보험가액(保險價額)에 따라 정(定)해야 한다는 의견(意見)이 있었으나(31.59%), 우리 나라에는 지역적(地域的) 위험율(危險率)에 큰 차이(差異)가 없을 것이므로 전국(全國) 일률적(一律的)인 보험료(保險料)를 보험가액(保險價額)에 따라 정(定)하기를 원(願)하는 경향(傾向)이 높았다(39.55%). 11. 보험료(保險料)의 납부(納付) 산림보험료(山林保險料)는 단기(短期)는 일시불(一時拂), 장기(長期)는 매년(每年) 납부(納付)하게 하는 의견(意見)도 있으나(13.80%), 단기(短期)는 고율(高率), 장기(長期)는 저율(低率)로 하되 단기(短期), 장기(長期)를 막론(莫論)하고 매년(每年) 납부(納付)하도록 하여야 한다고 반응(反應)하였다(86.71%). 12. 보험사무(保險事務) 취급기관(取扱機關) 산림보험(山林保險) 사무(事務)의 취급(取扱) 즉(即) 창구업무(窓口業務)의 취급(取扱)을 산림행정기관(山林行政機關)에 위탁(委託)하거나(18.75%), 일반(一般) 보험회사(保險會社)에 맡기기보다는(35.76%) 산림조합(山林組合)에 위탁(委託) 취급(取扱)하게 하고 보험료(保險料)의 일정율(一定率)을 환부(還付)해주는 것이 좋다고 반응(反應)하였다(44.22%). 13. 손해보상(損害補償)의 한도(限度) 산림보험(山林保險)의 손해보상(損害補償)은 유령림(幼齡林)이 피해(被害)를 입었을 때에는 재조림비(再造林費)를 한도(限度)로 하여 보상(補償)하는 것을 원칙(原則)으로 하고 성림(成林)의 경우(境遇)에는 손해액(損害額)의 80%정도(程度)를 한도(限度)로 하여 보상(補償)하기 보다는(29.70%) 실손(實損) 현재가액(現在價額)을 보상(補償)하거나(31.07%) 조림비(造林費)의 복리계산(複利計算) 합계액(合計額)을 보상(補償)하는 것을 바라고 있었다(36.99%). 14. 보험기금(保險基金)의 조성(造成) 산림보험(山林保險)의 기금조성(基金造成)은 손해(損害) 보상액(補償額)에서 일정액(一定額)을 공제(控除) 적립(積立)하여 조성(造成)하거나(15.65%), 임야세(林野稅)를 신설(新設)하여 기금(基金)을 확보(確保)하기 보다는(33.79%), 산림보험(山林保險) 무사고(無事故)로 인(因)한 잉여금(剩餘金)에서 일정액(一定額)씩을 적립(積立)하여 산림보험기금(山林保險基金)으로 하자는 의견(意見)에 많은 반응(反應)을 하였다(44.81%). 15. 산화(山火)의 원인(原因) 산림관계직(山林關係職)에 종사(從事)하고 있는 사람들의 과거(過去)의 경험(經驗)에 비추어 본 우리나라 산화(山火)의 주요원인(主要原因)은 실화(失火)(원인불명(原因不明), 32.39%), 담배불(28.89%), 화전(火田)(19.85%)에 의한 것으로 나타났는데 산림통계(山林統計)에 나타나 있는 산화(山火)의 주요원인(主要原因)과 일치(一致)하였다. 16. 산화경방(山火警防) 산림화재(山林火災) 경방조치(警防措置)로서 가장 중요(重要)하고 실효성(實効性)이 있으며 실천(實踐)할 수 있는 삼대대책(三大對策)으로는 (1) 방화선(防火線) 설치(設置)(23.84%), (2) 건조기(乾燥期)의 입산금지(入山禁止)(21.10%), (3) 메스콤에 의한 계몽교육(啓蒙敎育)(18.01%)이라고 반응(反應)하였다.

• 생물환경조절학회지
• /
• 제5권2호
• /
• pp.215-235
• /
• 1996

본 연구에서 수행한 Model 시뮬레이션에 의한 열환경 분석 기법은 지역별로 다양한 기상여건 하에서 대상온실의 난방 및 냉방부하를 보다 합리적으로 예측할 수 있을 뿐만 아니라 냉방이나 난방용 시스템의 결정을 비롯한 난방대책을 수립하고, 에너지 이용 전략의 수립이나 계절적인 작부계획 수립, 온실산업용 적지선정 등에 유익하게 활용될 수 있을 것이라 판단된다. 본 연구에서는 온실의 적극적인 환경조절 유형을 난방과 냉방의 두 가지로 대별하고, 난방 소요열량 산정을 비롯하여 야간의 보온 커튼효과, Heating Degree-Hour 산정 등 난방과 관련된 시뮬레이션은 동적 모형을 이용하여 시간별, 일별 및 월별로 검토하였으며, 환기를 비롯한 차광, 증발냉각시스템의 효과 분석은 정적모형을 이용하여 검토하였다. 특히 하절기 지하수와 같은 저온수를 직접 이용하거나 Heat Pump를 통하여 확보될 수 있는 저온수를 이용하여 온실의 피복면에 살수함으로서 확보할 수 있는 온실냉방효과를 검토하는 데는 1.2m$\times$2.4m 크기의 모형온실을 제작하여 기초실험을 수행함으로서 동절기의 수막시스템의 보온효과와 마찬가지로 하절기 냉방 효과를 거둘 수 있다는 가능성을 확인하였다. 본 연구에 활용된 온실의 수치 환경모형 중 난방관련 시뮬레이션용 동적 수치모형은 소기의 목적을 달성하는데 충분히 응용될 수 있는 이론모형이다. 이 이론모형이 범용성이 높은 것은 온실 내ㆍ외의 미기상 변화, 특히 난방이나 냉방이 본격적으로 요구되는 기간동안에 온도, 습도, 일사, 풍속 등의 미기상 인자들을 면밀하게 관찰하여 실측된 자료를 바탕으로 개발되었고, 다양한 자료에 의해 충분히 검정되었기 때문이다. 본 연구에서는 경남 진주지역의 어느 특정 기간(1987년)의 시간별 기상자료를 중심으로 온실의 열적 환경변화에 대한 수치모형 시뮬레이션을 실시하였으며, 아직 수치모형에 의한 시뮬레이션이 불가능한 일부 냉방효과를 검토하는 데는 모형 실험을 실시하였으며, 그 결과를 요약하면 다음과 같다. 1. 주간과 야간의 설정온도를 달리하고 다단계 변온조절방식으로 시뮬레이션을 행한 결과 난방 소요열량은 난방 설정온도에 따라 현저한 차이를 보였다. 특히 주간 설정온도에 비하여 야간 설정온도가 난방 소요열량에 예민하게 영향을 미치므로 야간의 설정온도 결정에 신중을 기해야 할 것으로 판단된다. 2. 기존의 Heating Degree-Hour 자료는 평균 외기온을 중심으로 임의의 설정온도에 대하여 산정된 값이므로 난방 소요열량에 대한 상대적인 비교수단은 되나 고려되는 기상인자의 제한과 설정온도의 임의성 때문에 실용성이 부족하다. 따라서 본 연구에서 제시된 것처럼 온실 주변의 제반 미기상 인자나 경계조건이 반영됨은 물론 작물의 생육상태 및 구체적인 설정온도까지도 고려하는 동적 수치모형으로 시시각각으로 예측된 실내기온을 중심으로 재배기간 동안의 난방열량을 적산함이 합리적이라 판단된다. 기존의 MDH 자료로 난방 설계를 할 경우에는 지나치게 과잉설계 될 가능성이 있다. 3. 산정된 난방 소요열량은 물론 커튼의 보온성능도 월별 기상여건에 따라 현저한 차이를 보이며, 시뮬레이션에 이용된 커튼의 경우 높은 보온효과를 보임으로서 년 평균 50% 이상의 난방 에너지를 절감할 수 있으며, 동절기 3-4개월의 집중 난방기에 에너지가 크게 절감됨을 발견할 수 있다. 4. 고온기 환기성능은 온실의 구조, 기상조건, 작물의 생육상태 등에 따라 다소의 차이가 있으나 환기율에 의해 크게 좌우되며, 시뮬레이션에 이용된 두 가지 농가보급형 온실 모두 환기율의 증가에 따른 실내기온의 강하 효과가 환기율이 1회/min 정도를 넘어서면서 급격히 둔화되는 현상을 보인다. 이는 기존에 권장되고 있는 적정 환기율인 1회/min 전후의 환기 시스템을 갖추는 것이 합리적임을 확인해 준다. 5. 작물이 성숙된 유리온실에서 외기의 상대습도가 50%인 쾌청한 주간동안 연속적으로 1회/min로 환기를 시킬 경우 실내기온 36.5$^{\circ}C$의 대조구에 비한 온도강하는 50% 차광만 했을 시 2.6$^{\circ}C$이고 효율 80%의 Pad ＆ Fan 시스템만 작동시 6.1$^{\circ}C$ 정도이며, 차광과 냉각시스템을 동시에 작동시는 약 8.6$^{\circ}C$로서 외기온보다 3.3$^{\circ}C$가 낮은 28$^{\circ}C$까지 실내온도를 낮출 수 있으나, 동일 조건하에서 외기의 상대습도가 80%로 높은 경우에는 Pad ＆ Fan시스템에 의한 온도강하가 2.4$^{\circ}C$에 불과하여 50% 차광하에서도 외기온 이하로 실내온도를 낮출 수 없음을 알 수 있다. 6. 하절기 3개월(6/1-8/31)동안 Pad ＆ Fan 시스템의 냉방효과($\Delta$T)는 설정된 작동 온도에 따라 다소 차이를 보일 것으로 예상되나 본 시뮬레이션에서 설정한 시스템의 작동 온도 27$^{\circ}C$에서 상대습도와의 상관관계는 대략 다음과 같았다: $\Delta$T= -0.077RH＋7.7 7. 전형적인 하절기 주간기상 하에서 경시적 냉방효과를 분석한 결과 환기만으로는 실내기온을 외기온 보다 5$^{\circ}C$ 높게 유지하는 정도가 고작이고, 차광이나 증발식 냉방시스템 만으로는 작물이 성숙한 단계에서조차도 외기온 이하로 떨어뜨리기가 어려우나 차광과 아울러 증발식 냉방을 병행할 경우에는 작물상태에 따라 다소 차이는 있지만 실내기온을 외기온보다 2.0-2.3$^{\circ}C$ 낮게 유지할 수 있음을 발견할 수 있다. 8. 일사가 차단된 27.5-28.5$^{\circ}C$의 외기온하에서 6.5-8.5$^{\circ}C$의 냉수를 온실 바닥면적 1$m^2$당 1.3 liter/min의 유량으로 온실표면에 살수했을 때 실내기온을 외기온보다 1$0^{\circ}C$ 낮은 16.5-18.$0^{\circ}C$ 정도로 낮출 수 있었다. 앞으로 살수 수온(T$_{w}$ )이나 외기온(T$_{o}$ ) 뿐만아니라 살수율(Q)에 따라 온실기온 (T$_{g}$ )에 미치는 상관 관계 T$_{g}$ = f(T$_{w}$ , Q, T$_{o}$ )를 구명하여 지하수 자체 또는 Heat Pump를 이용한 지하수온 이하의 냉수로 온실냉방의 가능성을 구명하는 것이 앞으로의 과제이다.

• 한국작물학회지
• /
• 제14권
• /
• pp.1-40
• /
• 1973

수도의 다수확을 위하여 근래 다비재배의 경향이 높아가고 있는 반면에 등숙률의 저하가 증수저해요인으로 크게 문제되고 있다. 특히 최근 육성된 통일품종은 이점이 더 심각한 바 있어 등숙의 향상책을 모색하고저 1970년부터 1972년까지 3개년간에 걸쳐 수원 작물시험장포장과 인공기상실에서 주로 진흥과 통일을 공시하여 증숙에 관한 일련의 실험을 시행한 바 그 결과를 요약하면 다음과 같다. 1. 통일의 곡립은 발아등 종래품종에 비하여 세장하고 곡립의 폭 및 두께가 작으며 비중과의 상관관계는 진흥에 있어서는 곡립의 무게, 두께, 폭 및 길이의 순으로 낮으나 통일은 무게, 폭, 두께 및 길이의 순으로 낮았다. 2. 비중별 립수분포에 있어서 종래의 Japonica도는 비중 1.18을 정점으로 대부분 1.12이상에 분포하고 있으나 통일계통에서는 1.12이하의 곡립도 상당수 분포하였고 진흥이 비중 1.06이하에서 정현비율이 급감하고 있으나 통일에 있어서는 비중 1.20에서 0.96까지의 곡립의 정현비율이 별로 차이가 없으므로 1.06을 등숙립의 선별기준으로 삼는 것은 불합리한 것으로 인정된다. 3. 출수후의 등숙속도는 품종간차이가 현저하며 대체로 한랭지 재배품종일수록 느렸으며 통일은 원래 등숙이 빠른 편이나 등숙후기에는 기온의 저하로 인하여 그 속도가 떨어졌다. 4. 지발분얼 또는 약세분얼은 수당영화수도 적을 뿐 아니라 등숙률도 낮은데 통일은 지발분얼이 많고 이들은 저온하에서 출수하여 수전일수가 연장되고 등숙률이 떨어졌다. 5. 통일의 엽신은 짧고 넓으며 엽신전개력은 다비조건에서는 진흥만큼 크고 또 엽의 경사각도는 적어 수광태세가 양호하였다. 통일 엽신의 단위동화능력은 고온하에서는 비교적 크나 저온하에서는 떨어졌다. 6. 통일은 단간이며 하위절간이 짧고 굵어서 도복저항성이 크고 출수전 저장탄수화물이 많았으며 인산, 규산, 석회, 망간 및 마그네슘 등의 체내함유율이 높았다. 7. 통일은 비교적 많은 영화수를 가지고 있고 진흥이 영화수와 등숙률간에 유의적인 역상관이 있음에 비하여 통일은 고온다조하에서는 영화수가 많아도 등숙률은 떨어지지 않고 영화수증가에 비례하여 수량이 많아졌다. 8. 진흥에 비하여 통일의 뿌리는 천근성이며 고온하에서는 그 활력이 컸으나 저온시에는 엽신이 황갈색으로 변하고 그 변색정도에 비례해서 뿌리의 활력도 떨어졌다. 9. 통일은 수광태세가 좋고 동화일호흡균형상 유리한 생산구조를 갖어 진흥보다 이상적인 모형이었다. 10. 수원지방의 수도보통기재배에 있어서 수량생산기간의 일사량은 비교적 풍부한 편이나 8월25일이후에 출수할 때에는 평균기온이 22$^{\circ}C$이하로 빠르게 하강하므로서 기온이 보다 등숙의 제한요인으로 인정된다. 11. 진흥이 저온하에서도 등숙율이 비교적 높은데 통일의 등숙적온은 $25^{\circ}C$이상이며 21$^{\circ}C$이하에서는 완전등숙이 거의 불가능하였다. 12. 진흥은 감광성이 비교적 크고 감온성은 중정도인데 비하여 통일은 감광성은 작으나 기본영양생장성과 저온하의 출수지연도가 컸었다. 13. 진흥은 질소의 후기중점시비에 의하여 등숙율이 향상되고 증수되었으나 통일에 있어서는 기비중점으로 질소를 시용하여 영화를 많이 확보하여도 등숙율저하가 적고 오히려 증수되였다. 14. 진흥은 만식적응성이 비교적 크나 통일은 조식효과가 크고 만식하면 출수가 지연되고 등숙온도가 낮아져서 등숙율과 수량이 떨어졌다. 15. 통일은 내비성과 밀식적응성이 커서 다비밀식조건에서 그 다수성을 발휘하는 특성을 가졌으며 주수 및 묘수증가에 의하여 수전일수가 단축되고 등숙률이 향상되었다. 16. 재식거리를 좁히고 어느 정도 주당묘수를 늘리면 강세분얼비율이 높아졌다. 17. 인산은 저온시에는 등숙율을 상당히 향상시켰다. 이상을 요약해보면 종래품종들의 등숙향상을 꾀하자면 8월20일이전에 출수시켜야 하며 10a당 질소 7.5kg 이상의 과다한 기비를 억제하고 후기중점으로 시비하여 동화효율을 높여야할 것이다. 한편 통일은 곡립이 세장하고 식물체가 작고 뭉툭한 등 종래품종과 판이한 외부형태와 더불어 그 생리생태적 특성도 상이한 점이 많으므로 등숙립선별, 도정 및 재배법상에도 종전품종과 다른 고려가 있어야 할 것이다. 즉 등숙립 선별기준에 대하여는 통일의 비중별 입수분포 및 정현비율로 보아 종래의 등숙립 선별기준인 비중 1.06 보다는 0.96을 적용하는 것이 합리적이고 도정상으로는 통일의 곡립이 세장하고 폭 및 두께가 작다는 것을 고려하여야 한다. 재배법에 있어서 통일의 등숙률이 낮은 원인이 주로 약세분얼이 많고 저온하에서는 출수가 지연되고 뿌리와 엽신의 기능이 저하되며 불임이 증가되는 것으로 판명되었고 그 외에 통일은 다비밀식적응성이 크므로 등숙향상과 수량 증대를 위해서는 적극적인 방법으로서 우선 견실하고 큰 묘를 가능한 한 조식하고 다비밀식상태로 재배하되 충분한 기비를 시용하고 묘수를 3본 내외로 심고 인산 및 규산등을 충분히 시용하여야 할 것이다.