• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.778-784
• /
• 2002

FFU are used increasingly by the microeleceronics industry to provide clean recirculating air for the fabrication of integrated circuits and laminar flow air. There may be several hundred ffu in a large cleanroom, covering 100% of the ceiling area. Hence, there is of often knowledge in the inside and outside of the country the flu give rise to noise & vibration trouble to microelectronics industry. Noise ＆ Vibration control for satisfication about noise ＆ vibration criteria in TFT-LCD factory cleanroom be in need of exact noise & vibration data of accurence from utility & equipment that can be exert a bad influence upon cleanroom. In this pater, hence we found out noise and vibration properities of ffu by using experimental method. And, we performed noise ＆ vibration analysis about noise it vibration level in cleanroom using semiempirical method for quantative approach about noise ＆ vibration level in cleanroom.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2002년도 추계학술대회
• /
• pp.273-277
• /
• 2002

In the electrode fabrication of unit cell, we found that optimal the electrochemical characteristics were obtained with at 90 wt.% of activated carbon(BP-20), 5 wt.% of conducting agent(Ppy, Super P) and 5 wt.% of P(VdF-co-HFP)/PVP mixed binder. The electrochemical characteristics of unit cell with Ppy improver were as follows : 37.6 F/g of specific capacitance, 0.98 $\Omega$ of AC-ESR, 2.92 Wh/kg and 6.05 Wh/L of energy density, and 754 W/kg and 1,562 W/L of power density. It was confirmed that internal resistance were reduced due to the increase of electrical conductivity and filling density by the introduction of conductivity agent, and content of conducting agent was suitable in the range of 4~6 wt.%. According to the impedance measurement of the electrode with conductivity agent, we found that it was possible to charge rapidly by the fast steady-state current convergence due to low equivalent series resistance(AC-ESR), fast charge transfer rate at interface between electrode and electrolyte, and low RC time constant.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2003년도 추계학술대회
• /
• pp.335-343
• /
• 2003

In the electrode fabrication of unit cell, it was ascertained that electrochemical characteristics were greatly increased with 90 wt.% of BP-20, 5 wt.% of Super P and 5 wt.% of mixed binder [P(VdF-co-HFP) : PVP =7 : 3] The self-discharge of unit cell showed that diffusion process was controlled by the ion concentration difference of initial electrolyte due to the characteristics of Electric Double Layer Capacitor (EDLC) charged by ion adsorption in the beginning, but this by current leakage through the double-layer at the electrode/electrolyte interface had a minor effect and voltages of curves were remained constant regardless of electrode material. The electrochemical characteristics of 2.3 V/3,000 F grade EDLC were as follows: 0.35 m of DC-ESR (100 A discharge), 0.14 mof AC-ESR (AC amplitude 100 mV), 2.80 Wh/kg (3.73 Wh/L) of energy density and 4.64 kW /kg (6.19 kW/L) of power density. Power output was compatible with electric vehicle applications, uninterrupted power supply and engine starter, in due consideration of Ragone relations.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권4호
• /
• pp.32-38
• /
• 2008

This paper describes a fast tool control (FTC)-based diamond turning process for fabricating large-area high-quality micro-lens arrays. The developed FTC unit has a stroke of $48{\mu}m$ and a resonance frequency of 4.9 kHz. Micro-lens arrays were fabricated using a micro-cutting tool with a nose radius of $50{\mu}m$. The FTC unit was integrated with a force sensor so that the initial position of the micro-cutting tool with respect to the workpiece surface could be detected through monitoring the contacting force. The length and depth of the designed parabolic micro-lens profile were $190{\mu}m$ and $20{\mu}m$, respectively. A micro-lens array was fabricated on a cylinder surface over an area of ${\phi}55 mm{\times}40 mm$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.409-412
• /
• 2000

A high performance EEG signal measurement system is fabricated. It consists of high precision pre-amplifier and auto identification bandwidth unit. High precision pre-amplifier is composed of signal generator, signal amplifier with a impedance converter, body driver and isolation amplifier. The pre-amplifier is designed for low noise characteristics, high CMRR, high input impedance, high IMRR and safety, Auto identification bandwidth unit is composed of AD-converter and PIC micro-controller for real time processing EEG signal. The performance of EEG signal measurement system has been shown the classified bandwidth through the clinical demonstrations.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권6호
• /
• pp.768-773
• /
• 1995

We describe a manufacturing method and characteristics on components of molten carbonate fuel cell. Cr, Al, AI$_{2}$O$_{3}$, Co, MgO powder were mixed with Ni powder for anode components and NiO was used for cathode electrode. The electrolyte plate consisted of LiAIO$_{2}$ and carbonate (Li$_{2}$CO$_{3}$/K$_{2}$CO$_{3}$=62/38) and these three were manufactured by doctor-blade method. As a result, open circuit voltage was 1.05[VI at Ni-10Cr anode and porosity was above 60[%].

• Journal of the Optical Society of Korea
• /
• 제18권3호
• /
• pp.251-255
• /
• 2014

A fiber diffuser sheet based on poly (ethylene naphthalate) (PEN) and poly (methylpentene) (PMP) has shown potential for liquid crystal display backlight units, but these materials have an interfacial adhesion problem. To improve the interfacial adhesion between the fibers and matrix components, we have proposed the use of amorphous poly (cyclohexane-1,4-dimethylene terephthalate) (Tritan) instead of PEN. Furthermore, the fabrication processes have been optimized and simplified to improve the optical and mechanical properties of the sheet. As a result, the most effective fiber content for achieving the best haze characteristics of a sample consisting of Tritan and PMP has been identified.

• 한국방사선학회논문지
• /
• 제12권7호
• /
• pp.879-886
• /
• 2018

3-dimensional(D) 프린터는 컴퓨터로 모델링 한 데이터를 바탕으로 3차원의 입체 물체를 출력할 수 있는 장비이다. 이러한 특징을 방사선과학 분야와 융합하여, CT 데이터를 이용한 뼈 모형 X선 팬텀제작 등에 활용되고 있다. 본 연구는 기존의 Pelvis팬텀을 CT 스캔하고 얻어진 데이터로 Fused Filament Fabrication(FFF) 3D 프린터의 소재인 PLA, Wood, XT-CF20, Glow fill, Steel 필라멘트를 이용하여, 뼈 모형 팬텀을 제작하였다. 기존의 Pelvis 팬텀과 3D 프린터로 제작된 5가지 재질의 팬텀을 동일한 조건으로 CT 스캔 하고 얻어진 영상에서 Hounsfield Unit(HU)을 측정하였으며, 진단용X선 발생장치를 이용하여 SI, SNR을 측정하여 각 팬텀을 비교 분석하였다. 그 결과 사지 X선 검사 조건 내에서 X선 팬텀은 glow fill 필라멘트가 가장 적합하다는 것을 알 수 있었다. 본 연구의 기반으로 필라멘트의 특성들을 알 수 있었으며, X선 팬텀 제작에 대한 실용성을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.617-618
• /
• 2008

• 전기의세계
• /
• 제19권4호
• /
• pp.12-17
• /
• 1970

BaO.nFe$_{2}$O$_{3}$ Powder ferrite magnet was made by sintering process. The purity of the powder were 99.6% far BaO. 99.5% for Fe$_{2}$O$_{3}$, and the grain size 1-3 micron. The Optimum mixing ratio n=4.4 the optimum density 4.8gr/cm$^{3}$ and the optimum second sintering temperature 1260.deg. C was found. The theoretical bloch wall, dimension of domain and energy per unit volume of BaFe$_{12}$O$_{19}$ were compared with pure Fe. Also, the saturation magnetization and maximum energy product were computed.d.d.