• Journal of Bio-Environment Control
• /
• v.16 no.4
• /
• pp.309-313
• /
• 2007

Experiments were conducted to measure rooting and growth of rose cuttings as affected by medium composition and volume. Rosa hybrida 'Red Sandra' and 'Little Marble' were used as test plants. For medium composition test, rockwool, phenolic foam, perlite, vermiculite, peatmoss, coir and a commercial medium (Tosilee medium) were applied in single or mixed forms on the propagation bed with fog (200 sec./5 min.) installed to control the humidification time. 'Red Sandra' and 'Little Marble' cuttings were planted in 16-cell plastic pots and 72-cell plug trays, respectively. For the medium volume test, 72-cell plug trays and 16-cell or 9-cell plastic pots were used. Cuttings with an uniform node with a five-leaflet leaf was soaked in a $500mg{\cdot}L^{-1}$ IBA solution for 30 sec. A fogging system installed on the propagation bed was used for (100 sec./5 min.). Rockwool 1 : peatmoss 1 (v/v) was the most effective on growth and rooting for both cultivars and high volume of Tosilee medium and rockwool were most effective media far both cultivars.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.5
• /
• pp.320-333
• /
• 2019

In this study, a physics-based 3D morphology model for the estimation of an erosion rate of nourished beach is newly proposed. As a hydrodynamic module, IHFOAM toolbox having its roots on the OpenFoam is used. On the other hand, the morphology model comprised a transport equation for suspended sediment, and Exner type equation derived from the viewpoint of sediment budget with the bed load being taken to accounted. In doing so, the incipient motion of sediment is determined based on the Shields Diagram, while the bottom suspended sediment concentration, the bed load transport rate is figured out using the bottom shearing stress directly calculated from the numerically simulated flow field rather than the conventional quadratic law and frictional coefficient. In order to verify the proposed morphology model, we numerically simulate the nonlinear shoaling, breaking over the uniform beach of 1/m slope, and its ensuing morphology change. Numerical results show that the partially skewed, and asymmetric bottom shearing stresses can be successfully simulated. It was shown that sediments suspended and eroded at the foreshore by wave breaking are gradually drifted toward a shore and accumulated in the process of up-rush, which eventually leads to the formation of swash bar. It is also worth mentioning that the breaker bar formed by the sediments dragged by the back-wash flow which commences at the pinnacle of up-rush as the back-wash flow gets weakened due to the increased depth was successfully duplicated in the numerical simulation.

• Journal of Korea Society of Industrial Information Systems
• /
• v.25 no.6
• /
• pp.47-54
• /
• 2020

The acupressure is a treatment that applies pressure to certain parts of the body and has been mainly used for pain relief in the field of oriental medicine. However, the treatment effect is often different depending on the practitioner's ability, experience, and physical strength, so standardized acupressure is needed. In this regard, the equipment is being released, but this is mainly a rolling massage method, which reduces energy concentration and poses a risk of injury. Therefore, in this study, a device that provides vertical acupressure based on variable bogie (wheel truck) was implemented. As a result of experimenting with load and body pressure distribution and desirability to validate the device's bearing pressure, the acupressure rod held up to 150kg, the body pressure ratio was measured lower than the body pressure ratio of the comparison item in section 0%

• Clean Technology
• /
• v.27 no.1
• /
• pp.61-68
• /
• 2021

Selective catalytic reduction (SCR) is widely used as a method of removing nitrogen oxide in large-capacity thermal power generation systems. Uniform mixing of the injected ammonia and the inlet flue gas is very important to the performance of the denitrification reduction process in the catalyst bed. In the present study, a computational analysis technique was applied to the ammonia injection system design process of a denitrification facility. The applied model is the denitrification facility of an 800 MW class coal-fired power plant currently in operation. The flow field to be solved ranges from the inlet of the ammonia injection system to the end of the catalyst bed. The flow was analyzed in the two-dimensional domain assuming incompressible. The steady-state turbulent flow was solved with the commercial software named ANSYS-Fluent. The nozzle arrangement gap and injection flow rate in the ammonia injection system were chosen as the design parameters. A total of four (4) cases were simulated and compared. The root mean square of the NH3/NO molar ratio at the inlet of the catalyst layer was chosen as the optimization parameter and the design of the experiment was used as the base of the optimization algorithm. The case where the nozzle pitch and flow rate were adjusted at the same time was the best in terms of flow uniformity.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1B
• /
• pp.125-135
• /
• 2008

The purpose of this study is to quantify the erosion parameters of cohesive sediments in Keum Estuary. This study also involves the examinations on the local/seasonal variation of them in Keum Estuary and on their spatial variation comparing with those of other sites. As erosional properties of cohesive sediments are in general influenced largely by the physico-chemical properties of cohesive sediments themselves, this study also involves the qualitative analyses on the impact by the physico-chemical properties. Erosion tests have been performed under the uniform bed condition using the Chonbuk annular flume and total 16 tests have been carried out with various bed densities and bottom shear stresses. Experimental results show that the critical shear stress for erosion varies in the range of $0.19{\sim}0.41N/m^2$ and the coefficient of erosion rate varies in the range of $54.26{\sim}7.70mg/cm^2{\cdot}hr$, over the corresponding bulk-density range of $1.14{\sim}1.38g/cm^3$. While erosion parameters estimated for Keum estuary sediments are found to be remarkably different in quantity compared with those for cohesive sediments from other sites, their local/seasonal variabilities within Keum Estuary are found to be insignificant.

• Journal of Korea Water Resources Association
• /
• v.44 no.2
• /
• pp.157-167
• /
• 2011

A numerical model was developed to predict the stage-discharge curve and lateral distribution of unit discharge in open channels with nonuniform cross section or compound open-channels. The governing equation is the one-dimensional momentum equation based on assumptions of the steady and uniform flow conditions in the longitudinal direction and the uniform water surface elevation in a cross section. Vegetative drag force term was included in governing equation in order to reflect the effect of floodplain vegetation on the flow characteristics. Finite element method was applied to obtain the numerical solution of the governing equation. Stage-discharge curve and lateral distribution of unit discharge for a given water surface are calculated based on input data, such as the cross sectional geometry, Manning's roughness coefficient, vegetative information and longitudinal slope of channel bed. The developed model was verified by comparing the calculated results with the observed data and the results of Darby and Thorne's(1996) model and the nonlinear k-$\epsilon$ model. The verified model was applied to estimate the upstream boundary conditions in two-dimensional flow model. The numerical results using laterally distributed unit discharge were compared with those obtained using uniformly distributed unit discharge in two-dimensional flow model.

• Journal of Bio-Environment Control
• /
• v.32 no.1
• /
• pp.8-14
• /
• 2023

This study was conducted to develop a precision automatic irrigation system in a nursery by considering the problems and improvements of manual and the conventional automatic irrigation system. The amount of irrigated water between the conventional automatic irrigation system and manual irrigation was 28.7 ± 4.4 g and 14.2 ± 4.3 g, respectively, and the coefficient of variation was less than 30%. However, the coefficient of variation of the conventional automatic irrigation system of 15%, was higher than that of manual irrigation of 30%. The irrigation test using the developed uniform irrigation system attached with the nozzle of a spray angle 80° and most highest uniformity was at height 600 mm. And coefficient of variation of the irrigation uniformity at the center part was within 20%, but irrigation amount of the edge part was lower 50% and over compared to the center part. As a result of a tomato grafting seedling cultivation test using the developed uniform irrigation system, the average plant height of seedling at the edge part was 28 mm but plant height at the center part was higher as 72 mm. Therefore, it was necessary to apply additional irrigation device at the edge part. The irrigation uniformity of the edge concentrated irrigation system was investigated that the irrigation amount of the edge part was irrigated by more than 50% compared with the center part, and coefficient of variation of the irrigation amount at the center part was less than 30%. As a result of a cucumber grafting seedling cultivation test using the edge concentrated irrigation system, the plant height of seedlings in the edge and central part of cultivation bed were 24% and 26%, respectively, so irrigation uniformity was higher then the uniform irrigation system. In order to improve the uniformity of seedlings, it is necessary to adjust the height of boom according to the growth of the seedling by installing a distance sensor in the overhead watering and boom irrigation system.

• Clean Technology
• /
• v.7 no.3
• /
• pp.169-178
• /
• 2001

Textile printing prints around twenty bilion linear meters of textile each year. Rotary and flat bed screen printing requires pre and post treatments, leading to the loss of dyes and the environmental problems due to effluents. Digital ink jet printing can offer a solution to the existing problems, especially the environmental problems, in addition to its flexibility. Pigments are used as a dispersion inks in the digital inkjet textile printing. Molecular dynamic simulation like Stokesian dynamic simulation was employed to simulate the behavior of pigments and velocity distribution under the pressure driven flow in the printer nozzle. The simulation shows that the particle distribution in the flow are uniform if particle volume fraction is low, the ratio of nozzle and particle diameter is large, and the dimensionless average suspension velocity is low.

• Journal of Korea Water Resources Association
• /
• v.42 no.4
• /
• pp.271-279
• /
• 2009

The objective of this study is to develop the scheme to apply one-dimensional finite volume method (FVM) to natural river with complex geometry. In the previous study, FVM using the Riemann approximate solver was performed successfully in the various cases of dam-break, flood propagation, etc. with simple and rectangular cross-sections. We introduced the transform the natural into equivalent rectangular cross-sections. As a result of this way, the momentum equation was modified. The accuracy and applicability of newly developed scheme are demonstrated by means of a test example with exact solution, which uses triangular cross-sections. Secondly, this model is applied to natural river with irregular cross-sections and non-uniform lengths between cross-sections. The results shows that the aspect of flood propagation, location and height of hydraulic jump, and numerical solutions of maximum water level are in good agreement with the measured data. Using the developed scheme in this study, existing numerical schemes conducted in simple cross-sections can be directly applied to natural river without complicated numerical treatment.

• Journal of Sericultural and Entomological Science
• /
• v.16 no.2
• /
• pp.133-139
• /
• 1974

The objective of this study is to compare the effects of raw materials as method of speeding up mounting of matured silkworm, for reducing concentrated labor during mounting periods. The results obtained from this study are summarized as fellows： (1) Quercus acutissima Carrs showed the most remarkable effect of repellent. Persicaria blumei Gross and Artemisia asiatica Nakai were followed in order. The rest repellents were also expected to be applicable. considering known material (silk-up) with lower mounting percentage. (2) The effective methods of preparation of repellent were to make distillate. Decocted solution type was considered to be the easiest way of preparation. (3) It seemed to be that there was little effect of repellent on the qualities of cocoon and silk. (4) When a repellent was applied to a silkworm bed, immatured silkworms were observed to mount. Thus it suggests that the repellent will give remarkable effects only when the degree of matured of silkworms is uniform.