• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2528-2533
• /
• 2007

Thermoforming is one of the most versatile and economical processes available for the manufacturing polymer products. The drawback of thermoforming is difficult to get uniform thickness of final products. For the distribution of thickness strongly depends on the temperature distribution of sheet, the adjustment of heater power is very important In this paper, an optimization study for getting uniform temperature distribution was carried out using dual optimization steps. At first, the steady state optimal distribution of heater power is searched by numerical optimization to get uniform temperature of sheet surface. In the second step, time-dependent optimal heater inputs have been found out to decrease the temperature difference through the direction of thickness using Rseponse Surface Method and D-optimal method. The optimization results show that the time-dependent optimal heater power distribution gives acceptable uniform sheet temperature in the field of forming temperature..

• 소성∙가공
• /
• 제7권4호
• /
• pp.393-399
• /
• 1998

For minimizing wall thickness thinning of circular shells, a new stamping technology, the deep draw-ing process combined with ironing is approached and investigated. The design requirements for the deep drawing shells are to keep the optimum wall thickness with max. 10 percent thickness thinning of the initial blank thickness, to make uniform thickness strain distribution for the wall of circular shell and to improve the shape accuracy for the roundness and concentricity. In order to check the validity and effectiveness of proposed work, a sample process design is applied to a circular shell needed for a 4multi-stepped deep drawing. Through experiments, the variations of the thickness strain distribution in each drawing process are observed. Also a series of experiments are performed to investigate optimum process variables such as the geometry of tooling, radius and drawing rate. In particular, the advantage of current approach with ironing is shown in contrast to the conventional deep drawing process. From the results of proposed method, the optimum value of process variables are obtained, which contribute more uniform thickness strain distribution and better quality in the drawn product.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권4호
• /
• pp.51-56
• /
• 2008

Thermoforming is one of the most versatile and economical processes available for shaping polymer products, but obtaining a uniform thickness of the final product using this method is difficult. Heater power adjustment is very important because the thickness distribution depends strongly on the distribution of the sheet temperature. In this paper, the steady-state optimum distribution of heater power is first ascertained by a numerical optimization to obtain a uniform sheet temperature. The time-dependent optimal heater input is then determined to decrease the temperature difference through the direction of the thickness using the response surface method and the D-optimal method. The optimal results show that the time-dependent optimum heater power distribution gives an acceptable uniform sheet temperature in the forming temperature range by the end of the heating process.

• 소성∙가공
• /
• 제7권6호
• /
• pp.610-619
• /
• 1998

The superplastic blow forming technology has advantages of cost reduction and low material consumption. compared to the conventional sheet metal forming technology due to the capability of precisely forming with high elongation and low flow stress. however it has a disadvantage that its partial thickness distribution is non-uniform. A processing technology like diaphragm forming has been developed even though it is difficult to prepare materials for superplastic blow forming. in this study a hemisphere forming of sheet before superplastic forming. It was found that the rotary forming material was less in quantity of cavitation at pole than that of hemisphere part that was superplastic formed without rotary forming treatment. Also discussed are the critical strain which is closely related to cavity shape and size.

• Design & Manufacturing
• /
• 제12권2호
• /
• pp.5-10
• /
• 2018

Vacuum-assisted thermoforming is one of the critical steps for successful application of film insert molding(FIM) to parts of complex shape. In this study, the simulations and experiments of thermoforming processes were performed to investigate the effects of process conditions on thickness distribution and printed pattern deformation of films in vacuum-assisted thermoforming. The film thickness uniformity increased with decreasing film heating time, whereas it increased with increasing vacuum delay time. After thermoforming of films with uniform pattern space of 5mm, the maximum space was 9.432mm. Based on the simulation, a modified pattern was calculated to obtain uniform spaces after thermoforming. In the experiments for film with the modified pattern, the maximum space appeared 5.837mm. In, addition. the predicted patterns were in good agreement with the experimental results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.866-872
• /
• 2000

Superplastic forming processes by characteristic of low flow stress and high elongation have advantages to reducing on production cost and weight because of the product of complex form could be made in one part. However superplastically termed part has a characteristic of non-uniform thickness distribution along forming direction. Especially. since the thickness distribution affects on mechanical properties of product. the uniform thickness is very important. There are two solution procedure of implicit and explicit procedure to analyze the superplastic forming. In this study to analyze the thickness distribution two kinds of commercial programs of DEFORM and PAM-STAMP which implicit and explicit code are used respectly. The results from the two Programs were compared with eath other As a result implicit code were more suitable than explicit code for superplastic forming analysis.

• Steel and Composite Structures
• /
• 제22권4호
• /
• pp.889-913
• /
• 2016

Vibration analysis of embedded functionally graded (FG)-carbon nanotubes (CNT)-reinforced piezoelectric cylindrical shell subjected to uniform and non-uniform temperature distributions are presented. The structure is subjected to an applied voltage in thickness direction which operates in control of vibration behavior of system. The CNT reinforcement is either uniformly distributed or functionally graded (FG) along the thickness direction indicated with FGV, FGO and FGX. Effective properties of nano-composite structure are estimated through Mixture low. The surrounding elastic foundation is simulated with spring and shear constants. The material properties of shell and elastic medium constants are assumed temperature-dependent. The motion equations are derived using Hamilton's principle applying first order shear deformation theory (FSDT). Based on differential cubature (DC) method, the frequency of nano-composite structure is obtained for different boundary conditions. A detailed parametric study is conducted to elucidate the influences of external applied voltage, elastic medium type, temperature distribution type, boundary conditions, volume percent and distribution type of CNT are shown on the frequency of system. In addition, the mode shapes of shell for the first and second modes are presented for different boundary conditions. Numerical results indicate that applying negative voltage yields to higher frequency. In addition, FGX distribution of CNT is better than other considered cases.

• 소성∙가공
• /
• 제8권1호
• /
• pp.92-100
• /
• 1999

A procedure is proposed for determining the initial thickness distribution in oder to produce a specified final thickness distribution for the axisymmetrical superplastic blow forming processes. Weighted parameter is introduced to improve the simple ad $d_traction method and the initial blank thickness distribution is obtained by optimizing the weighted parameter. This method is applied to superplastic free bulging process with the uniform thickness distribution of final shape to confirm its validity. The optimum initial blank thickness distributions is obtained from arbitrary axisymmetrical superplastic blow forming processes such as dome, cone and cylindrical cup forming with die contact. It is concluded that the ad $d_traction method with weighted parameter is an effective method for an optimum blank thickness distribution design.esign.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.96-99
• /
• 2007

The microstructure with fine and uniform AGS(austenite grain size) along thickness direction over no recrystallization temperature is strongly required for production of the high strength steels. The previous AGS prediction only based on the average strain improves to find the rolling conditions for accomplishment of the fine grain, but cannot find those for uniform grain. In this paper, an integrated mathematical model for prediction of the strain distribution along thickness direction is developed by carrying out finite element simulation for a series of rolling conditions. Also, the AGS distribution after rough rolling is predicted by applying the proposed model with AGS prediction model.

• 한국화재소방학회논문지
• /
• 제11권3호
• /
• pp.15-23
• /
• 1997

In this study, the alumina for gas sensor was prepared by anodic oxidation. It was stable thermally and chemically, and pore diameter and pore distribution was uniform. And the shape of pore was cylinderical. The aluminum plate was carried out by the thermal oxidation, chemical polishing and electropolishing pretreatment. The pore diameter, pore size distribution, pore density and thickness of alumina was observed with the change of reaction temperature, electrolyte concentration and current density. As a results, It was able to use for carrier because alumina which was prepared by anodic oxidationhas uniform pore size distribution.