• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.3
• /
• pp.277-280
• /
• 2001

General source location method that use an arrival time differences among sensors is restricted to the composite material and the complex-shaped material. In this study, a bundle-type acoustic sensor composed of 6 pinducers was utilized to determine wave propagation direction and then to estimate source location of the unidirectional GFRP. For the purpose of the study, slowness curve for the material was obtained and made an assumption that the incident waves on pinducers are propagated as a plane wave. According to the results, measured propagation directions of the wave were coincide with theoretical background, however, it was a hassle to determine the source location exactly. But, it is expected that bundle-type sensor gives more accurate results for zone location than generally used acoustic sensors.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.135-140
• /
• 2006

Numerical computations are made to predict wave loads on a vertical cylinder in an extreme wave. To generate the extreme wave, a frequency-focused unidirectional wave is adopted in three-dimensional numerical wave tank. The mathematical formulation is wide in the scope of the potential theory with fully nonlinear free surface conditions. As a numerical method, finite element method based on variational principle is applied. Comparisons between the present numerical results and the previous computation data. show a good agreement.

• Journal of the Korean Ceramic Society
• /
• v.27 no.4
• /
• pp.567-573
• /
• 1990

Solidification condition for preparing transparent ${\gamma}$-6Bi2O3.GeO2 polycrystals by unidirectional solidification of melt, were investigaetd and the properties of the polycrystals prepared were measured. The ${\gamma}$-6Bi2O3.GeO2 polycrystals showing transparency like a single crystal were obtained by the unidirectional solidification of ${\gamma}$-6Bi2O3.GeO2 melt at a solidification rate of 0.5mm/h under a thermal gradient of 12$0^{\circ}C$/cm. The transparent polycrystals obtained showed the same photoconduction and optical activity as the ${\gamma}$-6Bi2O3.GeO2 single crystals grown by Czochralski method. But the electro-optic effect of polycrystals was heterogeneous because the colummar ${\gamma}$-6Bi2O3.GeO2 crystals were not oriented to the particular crystallographic direction.

• 한국기계연구소 소보
• /
• s.18
• /
• pp.163-168
• /
• 1988

Impregnation of molten thermoplastic resin into continuous unidirectional fiber bundles was investigated. The degree of impregnation is defined as the ratio between the number of impregnated fibers and the total number of fibers of a bundle. The degree of impregnation was modeled as a function of time, impregnation pressure, temperature and tow size assuming the radial inward flow through the fiber bundle is governed by the Darcy's law. The permeability was assumed to be constant. Experiments were performed to evaluate the validity of the medel. Today's T300 graphite fiber bundles and Polyetheretherketone(PEEK) resin was used. A fiber bundle and resin powder were put into a mold and pressure and temperature were applied. After a predetermined time, the sample was taken out and microphotographs of the cross-section were taken. From the microphotographs, the number of impregnated fibers was counted and then the degree of impregnation was determined. Experiments were also performed for different tow sizes. Good agreements were found between the model and the experiments rendering a confidence in the model.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.826-840
• /
• 2018

This paper presents a distributed maximum power point tracking (DMPPT) algorithm based on the reference voltage perturbation (RVP) method for the PV modules of a series PV string. The proposed RVP-DMPPT algorithm is developed to accurately track the maximum power point (MPP) for each PV module operating under all atmospheric conditions with a reduced hardware overhead. To study the influence of parameters such as the controller reference voltage ($V_{ref}$) and PV current ($I_{pv}$) on the PV string voltage, a small signal model of a unidirectional differential power processing (DPP) based PV-Bus architecture is developed. The steady state and dynamic performances of the proposed RVP DMPPT algorithm and small signal model of the unidirectional DPP based PV-Bus architecture are demonstrated with simulations and experimental results. The accuracy of the RVP DMPPT algorithm is demonstrated by obtaining a tracking efficiency of 99.4% from the experiment.

• Korean Management Science Review
• /
• v.11 no.1
• /
• pp.39-50
• /
• 1994

Carousel systems can be classified into unidirectional and bidirectional carousel, depending on the hardware structure. Bidirectional carousels again can be classified into reversible and irreversible carousel, depending on whether the reversal of direction is allowed or not during the process of an order. In this study, single carousel served by one operator is considered. Analytical models for the rotation distance to process an order of size are developed for unidirectional and irreversible bidirectional cases. For reversible bidirectional and Nearest Neighbor Heuristic cases, simulation results of the average rotation distance are presented. Since the throughput capacity of carousel systems also depends upon the picking time of the operator; order size; and the rotation speed of carousel, the model considers the above three factors to express the throughput capacity of single carousel systems.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.33 no.4
• /
• pp.346-351
• /
• 1997

The pin bearing strength is one of the most important design parameters for mechanical joints composed of fiber reinforced composites. Thus the effect of the edge distance and the width of specimen on the pin-bearing strength of unidirectional CFRP composites were experimentally investigated in this paper. As results, the failure modes and the pin bearing strength of mechanical joints turned out to depend on the edge distance and also the width of specimen. The failure of specimen with low ratio of width to hole diameter was caused by the net tension from the hole boundary, on the other hand, the failure of specimen with low ratio of edge distance to hole diameter was caused by the shear-out. The bearing strength in case of the failure by shear-out was quite lower than that in case of failure by net tension.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.474-479
• /
• 2008

The purpose of this paper is to estimate the fire safety in tunnels with bi-directional and/or congested unidirectional traffic where there may be people on both sides of the fire. Therefore, the spread and movement of smoke are simulated by Fire Dynamic Simulator code under different ventilation systems, longitudinal, semi-transverse, large port exhaust system. And as quantitative risk index, FED (Fractional Effective Dose) for each ventilation system are calculated and compared by existed code developed previous research.

• Advanced Composite Materials
• /
• v.16 no.2
• /
• pp.167-180
• /
• 2007

The tensile strength of unidirectional carbon fiber reinforced plastics under a high strain rate was experimentally investigated. A high-strain-rate test was performed using the tension-type split Hopkinson bar technique. In order to obtain the tensile stress-strain relations, a special fixture was used for the impact tensile specimen. The experimental results demonstrated that the tensile modulus and strength in the longitudinal direction are independent of the strain rate. In contrast, the tensile properties in the transverse direction and the shear properties increase with the strain rate. Moreover, it was observed that the strain-rate dependence of the shear strength is much stronger than that of the transverse strength. The tensile strength of off-axis specimens was measured using an oblique tab, and the experimental results were compared with the tensile strength predicted based on the Tsai-Hill failure criterion. It was concluded that the tensile strength can be characterized quite well using the above failure criterion under dynamic loading conditions.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.10
• /
• pp.2620-2633
• /
• 1996

In this paper, a new high-speed local area network using a dual mode switching access (DMSA) protocol implemented on a dual unidirectional bus is described. By utilizing the implicit positionalordering of stations on a unidirectional bus, the proposed system switches between random access mode and the token access model withoug unnecessary delay. Therefore, unlike other hybrid systems such as Buzz-net and Z-net, DMSA does not show a rapid degradation in performance as the load increases. We obtain the average channel utilization and the average access delay by using a simplified analytic model. The numerical results obtained via analysis are compared to the simulation resuls for a partial validation of the approximate model. The performance characteristics of DMSA are superior delay-throughput characteristics at light and medium loads, compared to compared to other LAN systems, and the capability of providing a single active station with full capabity of the channel.