• Korean Journal of Crystallography
• /
• v.14 no.2
• /
• pp.62-66
• /
• 2003

The preparation of n-type thermoelectric material of Bi₂ Te/sub 2.55/Se/sub 0.45/ doped with CuBr₂ was carried out using a vertical gradient freezing method. With this method, unidirectional solidified Bi₂Te/sub 2.55/Se/sub 0.45/ has been obtained. XRD analysis demonstrated that Bi₂/sub 2.55/Se/sub 0.45/ 5 ingot has grown with prefer orientation of (0 1 5) face. Seebeck coefficient and electrical conductivity were measured as functions of temperature in the range of 373 K to 523 K on the sample which prepared via VGF method.

• Advances in Energy Research
• /
• v.4 no.1
• /
• pp.47-68
• /
• 2016

A well designed hybrid power system (HPS) can deliver electrical energy in a cost effective way. In this paper, model for HPS consisting of photo voltaic (PV) module and wind mill as renewable energy sources (RES) and solar lead acid battery as storage device connected to unidirectional grid is developed for peak demand reduction. Life time energy cost of the system is evaluated. One year hourly site condition and load pattern are taken into account for analysing the HPS. The optimal HPS is determined for least life time energy cost subject to the constraints like state of charge of the battery bank, dump load, renewable energy (RE) generation etc. Optimal solutions are also found out individually for PV module and wind mill. These three systems are compared to find out the most feasible combination. The results show that the HPS can deliver energy in an acceptable cost with reduced peak consumption from the grid. The proposed optimization algorithm is suitable for determining optimal HPS for desired location and load with least energy cost.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.175-179
• /
• 2004

Since the electromagnetic properties of fiber reinforced polymeric composites can be tailored effectively by adding small amount of electromagnetic powders to the matrix of composites, they are plausible materials for fabricating the radar absorbing structures (RAS) of desired performance. In order to design the effective electromagnetic wave (EM) absorber with the fiber reinforced polymeric composites, the electromagnetic characteristics with respect to the constituents of the composite should be available in the target frequency band. In order to describe the dielectric behavior of low loss unidirectional fiber reinforced composite, theoretical models and mixture equations for estimating its dielectric constant were proposed with respect to the fiber, matrix volume fractions and fiber orientations, and verified by the experiments. From the investigation, it was found that the suggested binary mixture rules agreed well with the experimental results.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.43-47
• /
• 2002

Weight loss experiments have been performed for unidirectional carbon fiber/epoxy laminates under both isothermal and cyclic thermal conditions. It was found that weight losses were the result of both specimen-geometry dependent oxidative degradation and volumetric geometry dependent thermal degradation. Thermal degradation was found to play a major role in the overall weight loss process, and photomicrographs of cross-sectioned, aged specimens confirmed this fact. A method to predict the effect of isothermal environment on the weight loss was introduced and found to be in good agreement with experimental data at temperatures near Tg (glass transition temperature).

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.283-288
• /
• 2003

The object of this study is to investigate a fracture characteristics of static tensile test as a function of acoustic emission according to the fiber orientation $\theta=0^{\circ}C$ in carbon/epoxy composites, CFRP. On tensile loading, it was recognized that the fracture characteristics of CFRP in a unidirectional composites. Using the results of the AE analysis(a=2mm), it was found that the amplitude distributions of AE signals corresponding the matrix cracking, fiber debonding or delamination, and fiber breaking are 55~70dB(<200sec), 100dB(200~600sec), and 80dB(>600sec).

• Journal of Korea Foundry Society
• /
• v.18 no.3
• /
• pp.234-239
• /
• 1998

Unidirectional solidification of $Al-CuAl_2$ eutectic composites was studied under the condition of forced convection by vibration. It has been shown that thermal gradient for solid is different from that for liquid during solidification under force convection by vibration. With increase of vibration, mobility of liquid increases, but decreases with decreasing vibration. The rate of solidification is very high initially, and decreases suddenly. For further solidification, the rate of solidification decrceases slowly, and shows a L-type behavior. The mechanical vibration during solidification effects efficiently on nucleation, and induces a forced convection in liquid. By the forced convection, great thermal gradient of liquid interface between solid and liquid can be obtained. The amount of solute near the interface also decreases as solute distribution is improved by the forced convection.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.5
• /
• pp.429-436
• /
• 2016

Currently, many studies on green ships are under way. Fuel cell (FC) ships are of interest as future low-emission, fuel-efficient vessels. In this paper, a hybrid power management system for an FC ship was designed. The system consists of an FC, a battery, a unidirectional DC/DC converter, a bidirectional DC/DC converter, a filter, an inverter, and a propulsion component. To design the system, we analyze electric sources and converters, and create PLECS models of hybrid power management system. Then, we check the cold start sequence and perform a simulation to understand the characteristics of the hybrid power management system in an FC ship.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1261-1270
• /
• 2000

This paper is concerned with the development of a general model for predicting material damping in laminates based on the strain energy method. In this model, the effect of interlaminar stress on damping is taken into accounts along with those of in-plane extension/compression and in-plane shear. The model was verified by carrying out the damping measurements on $90^0$ unidirectional composite beams varying length and thickness. The analytical predictions were favorably compared with the experimental data. The transverse shear($$\sigma$_{yz}$) appears to have a considerable influence on the damping behaviors in $90^0$ unidirectional polymer composites. However, the other interlaminar stresses($$\sigma$_{xz}$, $$\sigma$_z$) were shown to have little impact on vibration damping in $90^0$ laminated composite beam.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.101-105
• /
• 1992

Machined graphite/epoxy composite surfaces were studied by using SEM(Scanning Electron Microscopy). surface profilometry and its analysis to determine suitable surface describing parameters for machined unidirectional and laminate composite surface. The surface roughness and profile are found to be highly dependent on the fiber layup direction and the measurement direction. Machined unidirectional and 0.deg. 45 .deg. 90 .deg. plies in laminate composite surface profiles are found to be Gaussian in the direction of machining. Since there exist bare fibers without matrix smearing in 0 .deg. ply, higher surface roughness values were found in this orientation. It was possible to machine 90 .deg. and -45 .deg. plies due to the adjacent plies, which were holding those plies. It was found that the microgeometrical variations in terms of roughness parameters Ra without Dy (maximum Damage Depth) region and Dy are better descriptors of the machined laminate composite surface than commonly used roughness parameters Ra and Ra. The characteristics of surface profiles in laminate composite are well represented in CHD (Cumulative Height Distribution) plot and PPD (Percentage Probability Density) plot. Also, the power spectral density function is shown to be capable of identifying the wavelength distribution of the machining damage.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.5
• /
• pp.415-422
• /
• 2013

In this paper, we present Self-Checking look-up-table (LUT) based on Scalable Error Detection Coding (SEDC) scheme for use in fault-tolerant reconfigurable architectures. SEDC scheme has shorter latency than any other existing coding schemes for all unidirectional error detection and the LUT execution time remains unaffected with self-checking capabilities. SEDC scheme partitions the contents of LUT into combinations of 1-, 2-, 3- and 4-bit segments and generates corresponding check codes in parallel. We show that the proposed LUT with SEDC performs better than LUT with traditional Berger as well as Partitioned Berger Coding schemes. For 32-bit data, LUT with SEDC takes 39% less area and 6.6 times faster for self-checking than LUT with traditional Berger Coding scheme.