• 상하수도학회지
• /
• 제17권4호
• /
• pp.567-573
• /
• 2003

The pretreatment process was carried out to solubilize the sewage sludge for enhancing its biodegradability using alkaline treatment, ultrasonic treatment(15kHz), ozone treatment and different combination of these three methods: alkaline followed by ultrasonic as well as ozone, and ultrasonic followed by alkaline. The solubilization efficiency was evaluated based on the SCOD/TCOD ratio and VSS/TS ratio. In results, the proper condition of alkaline treatment was shown as 30meq/l of NaOH, pH 12 and 3hours of reaction time. Solubilization efficiency increased to 17% from initial 2% based on SCOD/TCOD ratio under this condition. In ultrasonic treatment, the higher ultrasonic power, the longer treatment time and the lower sludge volume resulted in higher solubilization respectively. There was a rapid increase in solubilization efficiency after 20 minute, then it was measured as 32% of SCOD/TCOD ratio in 1 hour at a ultrasonic power of 1,300W with 1/sludge. Solubilization efficiencies in combined treatment using alkaline and ultrasonic were 47-53% higher than single treatment at a sonicated time of 1 hour. Ozone treatment followed by alkaline treatment also represented the enhanced solubilization compared to ozone treatment. Therefore, ultrasonic or ozone treatment assisted by alkaline could achieve the short treatment time as well as high solubilizetion efficiency.

• 한국식품영양과학회지
• /
• 제30권2호
• /
• pp.256-260
• /
• 2001

This study was carried out to investigate effect of ultrasonic treatment on the quality of frying chicken meat. Moisture content of ultrasonic treated leg meat was lowest to 59.7%, moisture content of breast meat was higher than leg meat and protein content of control was higher than ultrasonic treatment. Fat content of ultrasonic treatment was higher than control and leg meat was higher than breast meat. Hunter's L (lightness) and a (redness)-value was not different between frying methods, but L-value of breast meat and a-value of leg meat was higher than leg and breast meat, respectively. Hunter's b (yellowness)-value was not different among frying chicken meats. Frying loss of ultrasonic treatment was significantly lower than control, water holding capacity was higher than control. VBN content of ultrasonic treatment was comparatively higher than control, TBA number of ultrasonic treatment was highest to 0.78mg malonaldehyde/kg. Hardness, springiness and cohesiveness of frying chicken meat was not different between frying methods, but difference of chicken muscle parts were significantly showed. Chewiness was not different among frying chicken meats and shear force value of control breast meat was lowest to 1.9kg. In case of sensory score, aroma and taste of frying chicken meat were out different between frying methods, but texture, juiciness and palatability of ultrasonic treatment were higher than control and that of breast meat were higher than leg meat.

• 한국축산식품학회지
• /
• 제21권2호
• /
• pp.126-132
• /
• 2001

This study was carried out to investigate the effect of ultrasonic treatment on physicochemical and sensory properties of cooked chicken meat. Moisture content of ultrasonic treated breast meat was higher than that of control, fat content of control of breast and leg meat were higher than that of ultrasonic treatment, and protein of control of breast meat was higher than that of ultrasonic treatment. Hunters L(lightness)-and a(redness)-value were not different between cooking methods, L-value of breast meat and a-value of leg meat were higher without regard to cooking method. Hunterb (yellowness)-value was not different among cooking chicken meats. Cooking yield was not different between cooking methods, pH of ultrasonic treated chicken meats were higher than that of control. Water holding capacity and salt soluble protein extractability of ultrasonic treated breast meat were greater than that of control. Water soluble protein extractability of ultrasonic treated leg meat was higher than that of control, and shear force value was not different between cooking methods. Hardness, cohesiveness and gumminess were not different between cooking methods and parts of muscle. Springiness of ultrasonic treated leg meat was greater than that of control and chewiness of breast meat was higher than that of leg meat. Aroma, texture, juiciness and overall acceptability were not different between cooking methods, taste of ultrasonic treated leg meat was higher than that of control. In addition, the sensory scores of parts of muscle were affected greater than that of cooking methods.

• Journal of Biosystems Engineering
• /
• 제37권6호
• /
• pp.429-433
• /
• 2012

Purpose: While rapeseed oil, soy bean oil, palm oil and waste cooking oil are being used for biodiesel, the viscosity of them should be lowered for fuel. The most widely used method of decreasing the viscosity of vegetable oil is to convert the vegetable oil into fatty acid methyl ester but is too expensive. This experiment uses ultrasonic energy, instead of converting the vegetable oil into fatty acid methyl ester, to lower the viscosity of the waste cooking oil. Methods: For irradiation treatment, the sample in a beaker was irradiated with ultrasonic energy and the viscosity and temperature were measured with a viscometer. For heating treatment, the sample in a beaker was heated and the viscosity and temperature were measured with a viscometer. Kinematic viscosity was calculated by dividing absolute viscosity with density. Results: The kinematic viscosity of waste cooking oil and cooking oil are up to ten times as high as that of light oil at room temperature. However, the difference of two types of oil decreased by four times as the temperature increased over $83^{\circ}C$. When the viscosity by the treatment of ultrasonic energy irradiation was compared to one by the heating treatment to the waste cooking oil, the viscosity by the treatment of ultrasonic energy irradiation was lower by maximum of 22% and minimum of 12%, than one by the heating treatment. Conclusions: Ultrasonic energy irradiation lowered the viscosity more than the heating treatment did, and ultrasonic energy irradiation has an enormous effect on fuel reforming.

• 한국염색가공학회지
• /
• 제16권1호
• /
• pp.40-47
• /
• 2004

Alkaline treatment gives Sea-Island type yam to produce microfiber and silk-like touch. But this treatment have some problems in dyeing and finishing process. To solve some problem occurred in dyeing and finishing of polyester fabric, the ultrasonic treatment technique was used recently. This study was carried out to confirm the effect of the ultrasonic treatment on alkaline weight loss finishing of polyester fiber under general alkaline treatment conditions; NaOH concentration 2, 3, 4, and 5％, treatment time 5, 10, 15, and 20 minutes, treatment temperature 70, 80, 90, and 99'E, respectively. On the other hand, the three way lay out method was used to test of significant obtained data from alkaline treatment. It was found that weight loss increased with increasing the NaOH concentration, temperature, and time. Also, in case of PET/Co-PET fabrics by ultrasonic, weight loss and dissolution of microfiber were superior to PET/Co-PET fabrics without ultrasonic. Tensile strength and modulus decreased with increasing NaOH concentrations and hydrolysis time. Therefore, the effect of alkali hydrolysis by ultrasonic application was better than that of the conventional method.

• Elastomers and Composites
• /
• 제38권2호
• /
• pp.103-121
• /
• 2003

The application of powerful ultrasound to rubber recycling is a very recent field of study. An ultrasonic field creates high frequency extension-contraction stresses by acoustic cavitation. The breakdown of rubber network occurs primarily around pulsating cavities due to the highest level of strain produced by high-power ultrasound. Stronger reductions of cross-link density were observed at a higher pressure, indicating an important role of pressure during ultrasonic recycling. Visible bubbles were observed during ultrasonic treatment as a proof of acoustic cavitation. Shearing effect has a significant influence on improving the efficiency of ultrasonic treatment. After the ultrasonic treatment, the cross-link densities of NR/SBR blends were lower than those of NR and SBR due to the reduced degree of unsaturation and chemical reactions. Carbon black fillers increase the probability of bond scission during ultrasonic treatment, due to the restricted mobility. The mechanical properties of ground tire rubber (GRT)/HDPE blends were improved by ultrasonic treatment and dynamic revulcanization. Ultrasonic treatment of GRT in the presence of HDPE matrix was found to give better mechanical properties due to the chemical reactions between rubber and plastic phases.

• 펄프종이기술
• /
• 제45권5호
• /
• pp.44-48
• /
• 2013

Ultrasonic treatment of KOCC was tried to explore the possibility for improvement of KOCC quality as a raw material for making industrial packaging paper and paperboard. The effect of pH, stock consistencies and treatment times on the ultrasonic response of KOCC were investigated. WRV, apparent density, tensile index and burst index were improved as pH of KOCC slurry is increased. However highest tear index and stiffness were obtained at pH 8. It was also found that the highest WRV and strength properties could be obtained at 0.5% of KOCC consistency during ultrasonic treatment. WRV and most strength properties were improved with ultrasonic treatment time. It was found that ultrasonic treatment can be used as a useful mean for KOCC modificaton.

• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.38-45
• /
• 2010

Welding structures are designed to endure its expected life. The most important factors are life. Especially on welded structure, fatigue strength is critical. So this study performed a research on Box and T shape weldment specimen to examine the influence of welding type. In this experiment, the results indicate Box shape was available in more than T shape. Fatigue tests were performed to evaluate the fatigue strength of the both as-welded and statically pre-loaded specimens by 3 point bending load. Fatigue life can be improved by using Ultrasonic Impact Treatment(UIT) effect. Ultrasonic Impact Treatment(UIT) is excellent for eliminating the tensile residual stresses and generating compressive residual stresses which elevate fatigue strength of welded structures. Also, this shows that welding part has better fatigue life and welding was performed well. In this study, to evaluate the Ultrasonic Impact Treatment(UIT) effect, for welding structure, the experiment was conducted at various levels of stress range between 100MPa and 500MPa. From the test results, it was indicated that fatigue performance was improving by Ultrasonic Impact Treatment(UIT)

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 Proceedings of Pre-symposium of the 10th ISWPC
• /
• pp.149-152
• /
• 1999

A new process for deinking of colored offset newsprint, i.e. enzyme treatment in cooperation with ultrasonic wave was developed in the present study. The physical characteristics such as fiber length, coarseness, crystallinity index of the deinked pulps were investigated and the sugar residues released from the treatment were analyzed. It was found that colored offset newsprint could be deinked effectively by cellulase treatment when ultrasonic wave was applied. The brightness increased by 5% ISO over that of control experiment and the pigment content was reduced markedly. Though the ultrasonic wave had little effect on the strength and crystallinity of the pulp, the treatment of enzyme combined with ultrasonic wave reduced the coarseness and fiber length to some extent. It was also found that ultrasonic wave could accelerate the hydrolysis of cellulose and hemicellulose during the cellulase treatment.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.317-319
• /
• 2007

Recently, there were many researches for efficiency improvement of DSC. Among of these works, research of surface treatment is still a prerequisite for electron diffusion, light-harvesting and surface state of $DSC^{4)}$. Using of the surface treatment, it can be raise up porosity of $TiO_{2}$ nano-crystalline structure on $photo-electrode^{5)}$. There are chemical, physical, electrical and optical methods which raise up its porosity. In this paper, we have designed and manufactured MOPA-type ultrasonic circuit (100W, frequency and duty variable). Manufactured ultrasonic circuit to use to force cavity density and power into $TiO_{2}$ paste. Then, we have optimized forcing time, frequency and duty of ultrasonic irradiation for surface treatment of photo-electrode of DSC. In I-V characteristic test of DSC, ultrasonic and thermal treated DSC shows 19% improved its efficiency against established DSC.