• International Journal of Automotive Technology
• /
• 제4권4호
• /
• pp.203-211
• /
• 2003

This paper describes a method for a falling weight impact test to estimate the impact energy absorbing characteristics and impact strength of CFRP (Carbon-fiber reinforced plastics) laminate plates based on considerations of stress wave propagation theory, which were converted to measurements of load and displacement verses time. The delamination area of impacted specimens for the different ply orientations was measured with an ultrasonic C-scanner to determine the correlation between impact energy and delamination area. The energy absorbed by a quasi-isotropic specimen having four interfaces was higher than that of orthotropic laminates with two interfaces. The more interfaces, the greater the energy absorbed. The absorbed energy of a hybrid specimen embedding GFRP (Glass-fiber reinforced plastics) layer was higher than that of normal specimens. Also, a falling weight impact tester was built to evaluate the characteristics and impact strength of CFRPs.

• 한국생산제조학회지
• /
• 제23권2호
• /
• pp.173-177
• /
• 2014

In this study, a 20,000Hz ultrasonic horn was designed and fabricated using a finite element analysis. The horn's resonate frequency was 19,991Hz, and the harmonic response frequency was 20,000Hz. In order to observe the developed horn's performance, 4,000 pieces of displacement data were obtained using an optical sensor and were analyzed using a fast Fourier transform. Finally, the developed horn's resonate frequency was found to be 19,992Hz. The effect of the tip area of the developed horn on the weldability of a Cu sheet was experimentally investigated. It was found that the welding strengths of specimens welded using a small tip area were generally higherthan those of specimens welded using a large tip area.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.525-528
• /
• 2000

Piezoelectric ceramics can provide electro-mechanical transduction with high stresses but low displacement. To obtain larger displacements, several mechanical amplifying structures have been used. High alternating displacements can be obtained using resonant structure. In this paper, we designed three kinds of the bolt-tightened Langevin type ultrasonic vibrators whose resonant frequencies are 30[kHz], 40[kHz]. FEM(Finite Element Methode) was employed to calculated the resonant frequencies and maximum displacements of designed vibrators. The designed resonant frequencies and computer calculated frequencies were coincided. When input voltages were increased, maximum displacements were also raised. ANSYS was used to find resonant frequencies and calculate displacements of vibrators.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권10호
• /
• pp.433-437
• /
• 2005

This paper studied Rotary type ultrasonic motor which has cross type stator. The stator consists of hollowed cross type metal which has four piezoelectric ceramics on the ends of cross bars. When two harmonic voltages which have 90$^{\circ}$ phase difference given to ceramics, the elliptical motion was generated in the inside tips. Inside tips are contact with rotor and these elliptical motions are rotate the rotor The finite element analysis was used to optimize the dimension and displacement of the stator. And the analyzed results were compared with the experimental results of the motor. As results, the speed and the torque of motor was increased by increasing width of the cross bar. And the speed and torque o( motor was not influenced to length of cross bar. The speed and torque was linearly increased by increasing voltage. The maximum torque was generated when the motor fabricated length of cross bar and width of ceramics in the ratio of 1:2.

• 동력기계공학회지
• /
• 제12권1호
• /
• pp.58-65
• /
• 2008

A method to test thin-walled tubes by guided ultrasonic wave is reported. The principle is that applicate two types of axially symmetric ultrasonic tube modes and "longitudinal" modes with particle displacement, which is coupled in axial and radial directions for transverse failures and torsional modes, oscillating in the circumferential direction only, for longitudinal failures. Both types of modes propagate along the tube in the axial direction. Therefore, a pulse-echo technique is possible. The pulses are excited and received at one end of the tube without contact electro-dynamic transducers. As soon as the tubes is put into a transducer coil at one end, the test of the whole tube can be accomplished in a few milliseconds. It is not necessary to rotate and transport the tubes during the test.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.601-604
• /
• 2002

In this paper bolt-tightened Langevin type vibrator was designed using longitudinal-torsional vibration. These two vibrations make rotary displacement at the end of the vibrator. ANSYS was used to determine shape and dimension of the vibrator in addition to resonant frequency, displacement and stress distribution. This kind of vibrator can be applied for a brakeless and gearless rotary motor which has high torque at low speed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.681-684
• /
• 2003

Piezoelectric motors have been successfully developed for various applications like autofocus drives in camera lenses and handling equipment for high-accuracy positioning. In this paper, the travelling-wave motor which used in the camera lense, using bending vibration of a ring was studied. The basic structure of the motor is same but we suggested a few parameters for considering their design. The parameter is different from sine and cosine region of the voltage of the ceramic surface, displacement according to the wave number difference, and the phase difference. Same size of ceramics and aluminium ring were used for the stator. As a result, the displacement is dependent on the wave number.

• Structural Engineering and Mechanics
• /
• 제29권1호
• /
• pp.113-116
• /
• 2008

• 비파괴검사학회지
• /
• 제20권1호
• /
• pp.27-32
• /
• 2000

본 논문에서는 고출력 펄스 Nd:YAG 레이저를 이용해서 원반형 시편의 한쪽 면에서 초음파를 발생시키고 반대 면에서 피드백 제어에 의해서 안정화된 마이켈슨 간섭계를 이용하여 열탄성 영역에서의 초음파를 검출하였다. 이론식에 의해서 계산된 열탄성 영역에서의 초음파 변위 파형이 실험에서 얻어진 파형과 유사한 것을 확인하였고, 특히 종파와 횡파의 음속이 접촉식 트랜스듀서를 이용하여 펄스-에코법으로 측정한 음속과 거의 일치하는 것을 확인하였다. 레이저 초음파를 이용한 응용예의 하나로 원반형 시편을 노 안에 넣고 음속을 계측한 결과 온도의 증가에 따라 음속이 감소하는 것을 확인하였다.

• 조명전기설비학회논문지
• /
• 제18권2호
• /
• pp.115-124
• /
• 2004

본 논문은 링형 초음파모터의 진동모드에 의한 진동특성 개선을 제안하였다. 고정자의 압전세락믹과 탄성체에 대한 설계는 공진주파수, 진동모드 및 결합계수 등을 고려한 유한요소법(FEM)에 의해 계산되었다. 6차로부터 8차까지의 진동해석 결과를 통하여, 7차 모드는 결합효율, 최소전력소비 및 굴곡 진동에 있어서 매우 우수한 결과를 얻었다. 또한 7차 모드 이상에서는 입력전압에 대한 출력전류가 매우 크게 증가함을 알 수 있었다. 두께 0.5[mm]∼2[mm]까지의 진동계산 결과 0.5[mm]에서 진동변위가 매우 높은 값을 지님을 알 수 있었다. 이러한 해석결과로부터 본 연구에서는 약 43.86[KHz]의 공진주파수을 갖는 외경 50[mm], 내경 22[mm]의 초음파모터를 제조하였으며 다음의 시뮬레이션 결과 42.2[KHz]와 실험결과43.86(KHz)의 값을 얻었다. 따라서 본 논문의 타당성은 시뮬레이션 결과와 실험결과의 비교 검토를 통하여 거의 일치하는 결과를 입증하였다.