• The Journal of the Korean dental association
• /
• v.17 no.9 s.124
• /
• pp.701-708
• /
• 1979

A series of combined impressions, alginate impressions and rubber base impression made of the lower left quadrant of one subject having a cast gold crown with six reference marks on lower let 1st molar. the combined impressions of hydrocolloid were removed from the mouth at 2.5min, after the insertion of the tray. The alginate impressions were removed from the mouth at 2min, after the insertion of the tray. The rubber base impressions were removed from the mouth at 10min. The effect on the accuracy of the combined impressions, alginate impressions and rubber base impressions was obtained following results by comparing the distances between the reference marks in indirect stone cast with the standard measurements of the cast gold crown prior to cementation. The findings through this study could be summarized as follows; 1. The accuracy of combined impression was superior to that of alginate impression, but it was inferior to that of rubber base impressions. 2. Combined impressions produced a little distortion of the mesio-distal length, alginate impressions produced the largest distortion, ut rubber base impressions produced the least distortion.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.10a
• /
• pp.263-268
• /
• 2004

In the present study, a Nd;YAG Laser (pulse type) was used to emit ultrasonic signals to a test material. In addition, a total ultrasonic investigation system was designed by adopting a Fabry-Perot interferometer, which receives ultrasonic signals without any contact. For non-destructive test SM45C, which contains some flaws was used as a test material. Because it is easy to align light beam in receiver, and the length of the light beam does not change much even if convex mirror leans towards one side, confocal Fabry-Perot interferometer, which has stable frequency, and PI control are used to correct interfered and unstable signals from temperature, fluctuation and time shift of laser frequency. Stable signals are always obtained by the feedback of PI circuit signals in the confocal Fabry-Perot interferometer. The type, size and position of flaws inside the test material were examined by achieving the stabilization of an interferometer. This study presented a useful method, which could quantitatively investigate the fault of objects by using a Fabry-Perot interferometer.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.199-205
• /
• 2000

The stud female threads for stud bolts tend to degrade faster by high temperature over 450 C. Therefore, inspection for replacement cycle of stud bolts is used to carry out many kinds of method such as ultrasonic test(UT), magnetic test(MT), wobble test, visual test and hardness test. The visual inspection among those has been only applied for stud female threads generally and wobble test is often used to apply stud bolts. In this paper, wobble test is applied for evaluation of stud female threads on the contrary stud bolts especially. It is also applied three types of inspection method included wobble test on the two sites which is used for each other different operation cycle and three kinds of acquisition data are compared with evaluation methods. From the results, we have studied the characteristic exchanging of integrity evaluation data distribution according to using time and proposed managing method for female thread of stud on the power plants.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.3
• /
• pp.29-35
• /
• 2020

This paper studies the main parameters of tube-to-bar dissimilar material and shape friction welding for piping materials. The weldability of joint parts was investigated with respect to tensile tests, micro-Vickers hardness, the bond of area, and optical microstructure. The specimens are tested as-welded. Optimal welding conditions are n = 2000 rpm, HP = 50 MPa, UP = 100 MPa, HT = 5 sec, and UT = 10 sec when the metal loss (Mo) is 11 mm. Moreover, the same two materials for friction welding are strongly mixed with a well-combined structure of micro-particles without any molten material, particle growth, or defects. Therefore, the expected result of dissimilar material friction welding includes a reduction of cost and material in the welding process.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.11 no.2
• /
• pp.20-24
• /
• 2015

During refueling Outage, In-service inspections(ISIs) for the Nuclear Power Plant components are mandatory requirement in accordance with ASME Code Sec. XI. Especially, in current ultrasonic testing is one of the most important NDT techniques that are used for volumetric examination methods for nuclear power plant components, and accurate sizing of flaw indication by UT is essential to assure the integrity of the components. However, ASME code specifies minimum requirement for vessel examination procedure, and so far many different flaw sizing approaches have been tried to apply. Through the Round Robin Test(RRT), the accuracy of ultrasonic flaw sizing using DAC techniques was measured with the mock-ups simulating typical pressure vessel welds. These mock-ups contain artificially introduced flaws of known size and location. This paper shows experimental comparison data on the accuracy of techniques using such as 6dB drop, 50%DAC, 20%DAC and 20%DAC with beam spread correction, and also shows that diverse DAC techniques can be effectively applied to the assessment of the flaw sizing for pressure vessel welds in the stage of welding and fabrication.

• Journal of Astronomy and Space Sciences
• /
• v.14 no.2
• /
• pp.320-329
• /
• 1997

A solar radio spectrograph for monitoring solar radio emission was installed at Ichon branch of Radio Research Laboratory in 1995. The spectrograph consists of three different antennas to sweep a wide band of frequencies in the range of 30MHz~2500MHz. We have developed the operating software for the acquisition and the analysis of solar radio data obtained by solar radiospectrograph in order to carry out active solar radio observational studies. It was found that by using our software, we could have very good solar radio data for a sequence of three TYPE III bursts observed on 4 Nov. 1997. In this paper, we show the radio spectrograph and the result of the observation by its operating software.

• Korean Journal Plant Pathology
• /
• v.13 no.2
• /
• pp.90-94
• /
• 1997

Interaction of races of rice blast fungus and cultivars has been evaluated. Dongjinbyeo was infected by four KJ races and two KI races, while other varieties were susceptible to four to six KJ or KI races. Among the single spores reisolated from the leaf blast lesion of Dongjinbyeo after mixed inoculation of 10 races, 63% was race KJ-301 which produced a small number and small size lesions, while 30% was race KI-313 which produced a large number of lesions. However, 93% of single spores reisolated from Palgongbyeo was a highly virulent race KJ-105. On the other hand, all the races were equally reisolated from the susceptible cultivar Jinmibyeo. Frequency of races isolated from the naturally infected leaf blast lesions in the field was similar to that of reisolated races from the cultivars inoculated with 10 mixed races in the greenhouse. However, 30% of single spores isolated from the naturally infected Dongjinbyeo was race KI-329 ut ace KI-313 was not detected. Genetic relationship of the isolates collected from leaf and neck blast fungus of Jinmibyeo and Nakdongbyeo showed specific bands on RFLP-P64, However, their genetic similarity was 80%.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.6
• /
• pp.1013-1017
• /
• 2012

Advanced composite-sintered bushings are widely utilized in the areas of excavators and injection molding machines as a journal bearing. Since the bearings are mainly used under high loads, service life should be long and the stored oil of inner bushings has to be continually fed into the bearing. The composite-sintered bushings are consisted of the two different materials; outer steel materials and inner porous sintered materials respectively. High temperature diffusion bonding has been applied for holding the both materials of the bushing together. Therefore, it is very important that the bonding reliability has to be assured and evaluated in manufacturing process. Finite element method (FEM) is performed in order to evaluate the minimum allowable flaw sizes that are possibly generated in the composite-sintered bushings. Additionally, the composite-sintered bushings were undergone ultrasonic C-scan tests to find out the size of inherent flaws through artificially simulated UT signal analysis.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.3
• /
• pp.256-263
• /
• 2009

After several PWSCCs were found in Bugey(France), Ringhals(Sweden), Tihange(Belgium), Oconee, Arkansas, Crystal Fever, Davis-Basse, VC Summer(U.S.A.), Thuruga(Japan), USNRC and PNNL started the research on PWSCC, that is, the PINC project. USNRC required KINS to participate in the PINC project in May 2005. KINS organized the Korean consortium at March 2006 and Pre-RRT for RVHP were performed for the preparation of PINC RRT. Through these preliminary RRT, Korea NDE teams can learn and develop the detection and sizing technique for RVHP dissimilar metal weld. These techniques are now being prepared in Korea and need to be utilized for the In-service inspection of the RVHP and BMI of Korea Nuclear Power Plants. PINC RRT mock-ups will be helpful to training.

• The Journal of Korean Medicine
• /
• v.21 no.1
• /
• pp.53-61
• /
• 2000

Objectives: This study was camed out to examine the effect of five fractions of aqueous extract from Artemisia capillaris THUNB(ACT), on TGF, 1-induced apoptosis, cell viability, cell cycle progression and mRNA expression of apoptosis-related genes in human hepatocyte cell line HepG2. Methods: This study employed Tryphan blue exclusion assay, DNA fragmentation assay, Cpp32 protease activity assay and Quantitative RT-PCR analysis. Results: In the Tryphan blue exclusion assay, the butanol fraction of ACT with $TGF{\beta}$, l showed magnificent (Nice word, ut is it appropriate in a medical abstract\ulcorner) viability and the H2O fraction of ACT with $TGF{\beta}$, l also showed higher viability than only $TGF{\beta}$, l-treated group. DNA fragmentation assay showed that the butanol fraction and the H2O fraction carried inhibitory effects on apoptosis induction, with the butanol fraction displaying greater effects. The Cpp32 protease activity assay showed that the butanol fraction decreased Cpp32 protease activity. The H2O fraction of ACT had no significant effect on the Cpp32 protease activity. Quantitative RT-PCR showed that the butanol fraction suppressed Bax, p 15/INK4B, p21/Waf1, PAI-1 and increased Bcl-2 gene. Conclusions: The data shows that butanol fraction of ACT increases the hepatocyte viability and has the hepatocellular protective effect by the suppression of $TGF{\beta}$, l induced-apoptosis through gene regulation.