• The Journal of the Korea Contents Association
• /
• v.7 no.3
• /
• pp.42-49
• /
• 2007

This paper implements RFID(radio-frequency identification)System to which the system was apply SS(Spread Spectrum) method. The system designed by using the algorithm for microprocessor with PLL of the receiver, PN spread, modulation and demodulation of the transceiver, and transistor amplifier for the output of stabilized BPSK (Binary Phase Shift Keying) signal. furthermore, it reduced the interference of the signal by designing the micro-strip narrow banded patch antenna, which is convenient for printing and producing, and decreased the volume of filter size in the system. It is also designed for the lower powered system with the possible application to UHF band of $860\sim930MHz$ for the international standard frequency band, which is the quota share of RFID distribution system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.8
• /
• pp.1943-1949
• /
• 2010

In this paper, we developed a RFID tag antenna using one-sheet inlay pattern which consist of two different frequencies in one layer. The antenna in one-sheet inlay RFID tag does not use different kind RFID antennas in a card but implement 13.56MHz and 900MHz RFID tag antennas in one sheet. In order to evaluate the usability of proposed method, we configured test equipments and designed 6 different patterns and test the recognition distance of each pattern. Among the one-sheet inlay RFID tag antenna designs, the pattern no.5 has good performance with recognition distance of 5.34m at 900MHz and 3.5m at 13.56MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.541-548
• /
• 2013

This paper presents a vector network analysis system for 2-port scattering parameters of microwave devices using some basic microwave instruments/devices such as signal generators, vector voltmeter, directional couplers and frequency mixers. The analytical model and implementation method for scattering parameter measurements - which can replace the vector network analyzers - are presented. The performance of the implemented system is evaluated through 1- and 2-port scattering parameter measurements, respectively. The vector volt signals which determine the scattering parameters are detected in two distinct methods depending on the frequency band of interests; a direct-detection method with a single signal generator and vector voltmeter for relatively low band and a heterodyne method to frequency down-mix associated with an additional signal source as well as frequency mixers for high band are used, respectively. Using these two methods, scattering parameters of UHF and X bands are evaluated and their performances are verified through a comercial vector network analyzer.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2007.05a
• /
• pp.1306-1309
• /
• 2007

본 논문에서는 indoor 환경에서 CR 네트워크를 이용하기 위한 방안으로 CR-Wi-Fi device 시스템을 제안했으며 IU 을 보호하는 방법으로 CR beaconing 을 제안했다. IU 가 출현하면 UHF, VHF band 와 ISM band 로 동시에 이를 알리고 CR 네트워크가 간섭을 주는 경우 사용 중이던 채널 사용을 중지 혹은 이동하도록 명령해야 한다. 본 논문에서는 CR beaconing 방식을 제안하여 보다 효과적인 IU 보호 및 복구를 수행하도록 하였다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.12
• /
• pp.1321-1328
• /
• 2015

A radio is a half-duplex voice communication method using the PTT(: Push To Talk), occupy a single line calls during transmission. As an interface between the telephone and the radio, UHF and VHF, for voice communication between the different heterogeneous devices, A device automatically switches between the two devices is required. Therefore, in accordance with the performance of the voice switching apparatus for detecting a voice to be transmitted from an input signal, loss of the audio signal to be transmitted is subjected to Significant influence. Conventional method has the problem responding to noise by setting the level through simple means of amplitude of input signal, in other words, the energy level of the input signal. This paper, by using the audio signal processing techniques, this discriminated what the voice is among the input signal and substantiated a device for the automatic voice transmission between heterogeneous devices. With this proposal, I was confirmed of improvement of performance in the automatic voice switching device, could perform loss-less transmission of voice between heterogeneous devices.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.6
• /
• pp.1055-1060
• /
• 2020

This study is a study on the analysis and measurement of the radar cross-sectional area of a miniature aircraft. Radar cross-sectional area for miniature aircraft in advance were analyzed using an electromagnetic analysis tool, and an actual miniature aircraft was manufactured and measured in an anechoic chamber. When measuring, the old model was used as reference data for RCS(radar cross section) characteristics and applied to the test result data of the actual reduced model. The measurement method improved the accuracy of the measurement by applying time gating to remove the influence on the components scattered inside the anechoic chamber. The RCS test results of the reduced model showed relatively high RCS characteristics in the microwave band, as the previous analysis results. In the future, we plan to utilize the method of RCS analysis and measurement for the target of the radar in the VHF(Very High Frequency)/UHF(Ultra High Frequency) band with a relatively large wavelength.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.2
• /
• pp.68-73
• /
• 2002

In compared with air insulated switchgear, GIS has a high efficiency and confidence. Insulation method using $SF_6$ gas has a very excellent insulation characteristic for high voltage equipment but has a characteristic that insulation heredity is changed for internal unequal electric field. So analysis of time varying electromagnetic field in GIS is very important for structure design and trouble diagnosis process. In compared with established method, the SNM(Spatial Network Method) in this Paper can observe variation of electromagnetic field with real time and get result very similar to measurement. In order to Know variation of electromagnetic field distribution in fast moving particle, we make used of SNM.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1805-1807
• /
• 2004

This simulated partial discharge caused by 22.9[kV] power cable using XLPE(Peroxide Crosslinkable Polyethylene) insulation having the outside damage. Asone of the insulation diagnostic method a radiated electromagnetic waves were measured by an UHF method using a BiconiLog antenna(EMCO-3142) and a spectrum analyzer used to measure EMl, EMC. From results of this study, It was confirmed that discharge progress were possible to be estimated by the proposed method.

• International Journal of Contents
• /
• v.7 no.1
• /
• pp.1-7
• /
• 2011

A new power control algorithm for wireless communication which can be applied to various near distance communications and USN/RFID systems is proposed. This technique has been applied and tested to lithium coin battery operated UHF/microwave transceiver systems to show extremely long communication life time without battery exchange. The power control algorithm is based on the dynamic prediction method of arrival time for incoming packet at the receiver. We obtain 16mA current consumption in the TX module and 20mA current consumption in the RX module. The advantage provided by this method compared to others is that both master transceiver and slave transceiver can be low power consumption system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.9
• /
• pp.1281-1287
• /
• 2015

We report the characteristics and differences of two types of attenuation measurement methods for electromagnetic partial discharge signal in GIS. The pulse method is to measure the attenuated waveforms in time domain and coverts them into frequency domain to get the attenuation spectra of given GIS section. This method simulates the real partial discharge signal. The frequency swept continuous wave method can obtain attenuation spectra directly so that it gives attenuation with low noise floor and simplicity. We show that both methods are effective and exchangeable because the attenuation results measured by two methods have similar trends