• Structural Engineering and Mechanics
• /
• 제73권3호
• /
• pp.353-365
• /
• 2020

In the previous studies, the authors proposed the use of laminated veneer lumber - carbon fiber reinforced polymer (LVL-CFRP) composite beams for structural application. Bond strength of the LVL-to-CFRP interface and flexural strengthening schemes to increase the bending capacity subjected to positive and negative moment were discussed in the previous works. In this article, theoretical models are proposed to predict the moment capacity when the LVL-CFRP beams are subjected to negative moment. Two common failure modes - CFRP fracture and debonding of CFRP are considered. The non-linear model proposed for positive moment is modified for negative moment to determine the section moment capacity. For the debonding based failure, previously developed bond strength model for CFRP-to-LVL interface is implemented. The theoretical models are validated against the experimental results and then use to determine the moment-rotation behaviour and rotational rigidity to compare the efficacy of various strengthening techniques. It is found that combined use of bi- and uni-directional CFRP U-wrap at the joint performs well in terms of both moment capacity and rotational rigidity.

• Advances in concrete construction
• /
• 제13권4호
• /
• pp.307-313
• /
• 2022

This paper performs an experimental study on the flexural behavior of preloaded reinforced self-compacted concrete beams strengthened with carbon fiber reinforced polymers CFRP. A group of six preloaded strengthened beams was investigated along with one unstrengthened beam used as a reference beam RB. All beams have the same dimensions and reinforcement details: three beams are strengthened with CFRP laminates against flexural failure and three beams are strengthened with CFRP sheets. For simulating actual conditions, the beams are loaded before strengthening. Then, after strengthening, the beams are tested for flexural strength using 4-point loads where cracked and ultimate load and failure mode, along with load-deflection relation are recorded. To study the different configurations of strengthening, one layer, two layers, and U-wrap formation of laminates and sheets are considered. The results show that strengthing the RC beams using CFRP is an effective method to increase the beam's capacity by 47% up to 153% where deflection is reduced by 5%-80%. So, the beams strengthened with CFRP laminates have higher load capacity and lower ductility in comparison with the beams strengthened with CFRP sheets.

• 설비공학논문집
• /
• 제27권9호
• /
• pp.463-467
• /
• 2015

The air-bubble sheet has been widely used to wrap fragile products for long-distance transportation. The further usage of the air-bubble sheet as a thermal-insulation material for the reduction of the thermal conductivities of window systems has occurred because of its low price, in addition to its thermal-conductivity properties. In this study, the thermal performances of a variety of commercial air-bubble sheets according to various applications were evaluated. The experiments were performed with single-glazed and double-glazed windows and three types of air-bubble sheets of different air volumes. U-values are used and were calculated for the determination of the thermal performances that are based on the KS F 2278. The maximum decrease of the U-value was measured as 1.092 when a sheet was attached onto the frame of single-glazed window. The square-like air-bubble sheet that contains the largest air volume shows the highest thermal-resistance value. Double layers of the air-bubble sheets show better performances than those of the single layers on both sides of the windows.

• Advanced Composite Materials
• /
• 제17권3호
• /
• pp.277-299
• /
• 2008

High quality and expedient processing repair methods are necessary to enhance the service life of bridge structures. Deterioration of concrete can occur as a result of structural cracks, corrosion of reinforcement, and freeze.thaw cycles. Cost effective methods with potential for field implementation are necessary to address the issue of the vulnerability of bridge structures and how to repair them. Most infrastructure related applications of fiber-reinforced plastics (FRPs) use traditional hand lay-up technology. The hand lay-up is tedious, labor-intensive and relies upon personnel skill level. An alternative to traditional hand lay-up of FRP for infrastructure applications is Vacuum Assisted Resin Transfer Molding (VARTM). VARTM uses single sided molding technology to infuse resin over fabrics wrapping large structures, such as bridge girders and columns. There is no work currently available in understanding the interface developed, when VARTM processing is adopted to wrap fibers such as carbon and/or glass over concrete structures. This paper investigates the interface formed by carbon fiber processed on to a concrete surface using the VARTM technique. Various surface treatments, including sandblasting, were performed to study the pull-off tensile test to find a potential prepared surface. A single-lap shear test was used to study the bond strength of CFRP fabric/epoxy composite adhered to concrete. Carbon fiber wraps incorporating Sikadur HEX 103C and low viscosity epoxy resin Sikadur 300 were considered in VARTM processing of concrete specimens.

• 패션비즈니스
• /
• 제12권3호
• /
• pp.31-53
• /
• 2008

This study is to suggest a brassiere pattern suitable to the Chinese woman by recognizing the differences among the brassiere patterns of Europe, America and Italy by comparison. Collected data was analyzed by using SPSS 12.0. 1. If seeing the length of the ordinary brassiere's wing in Korea, the mean is 31.02cm to be shorter than these 3 patterns. The length of a wing should be adjusted according to the degree of fabric's elasticity. 2. The ESMOD type shows a high angle of $60^{\circ}$ as the position of a shoulder strip is placed outward a lot compared with other patterns. 3. For the FIT and Marangoni types, the lengths of the inside and the external diameters show similarly to each other but the ESMOD type shows that its inside diameter is 7.5cm and external one is 9.6cm to have the difference of 2.1cm so that it is considered to put the bust together stronger than the others. 4. The cup circumference of the FIT pattern shows to be the biggest and that of the FIT pattern is the smallest. As the FIT pattern has the shape to wrap the side of the bust, it has large circumference but as it has a narrow angle of a dart, it seems to be fit to the woman with a small and flat bust. 5. For 1/2 of the nipple distance of the brassiere for the Korean adult women, it shows to be 6.12cm, much narrower than the patterns studied, and it is noticed that the ESMOD pattern is very similar to the brassier in the Korean market. 6. As the mean keeper height is 6.5cm, it is noticed that it is very similar to the brassier for the Korean adult women if comparing that the brassiere for the Korean adult has the keeper height of 6.5-8.6cm. The Marangoni pattern tends to have a little low and the ESMOD and FIT patterns have a ordinary measure.

• 유통과학연구
• /
• 제16권8호
• /
• pp.63-68
• /
• 2018

Purpose - Lettuce (Lactuca sativ L.) is one of the economically important vegetable crops, which worldwide market value is over 100 billion U.S. dollar. In Korea, about 89.7 kilo ton of lettuce was produced in 3400ha in 2016, recoded as No. 1 vegetable crop in domestic green house production. However, recently, domestic lettuce production and cultivation areas are all getting decreased. Thus, novel approaches are needed to be implemented to revive the production. Research design, data and methodology - In this review paper, we first prioritized the end-user traits which are imperative to positively stimulate the domestic lettuce market and discussed relevant genomics strategies. Especially, we assessed a possibility whether school meal program would be a potential niche market. Results - The genomics technologies, which become widely applied in the crop biotechnology since 2008 when next generation sequencing method was developed, may be a good solution in the crop improvement, efficiently gathering valuable information of agriculturally useful traits. Significantly, in lettuce, the high quality whole genome sequence, based on Lactuca sativa cv. Salinas, is publically available and this genomics platform, thus, would be implemented in lettuce breeding program to innovate relevant end-user traits both for the farmers and customers, including the disease resistance to the Fusarium wilt, productivity under hot weather conditions, various nutritional qualities and so forth. These improvements will boost domestic lettuce industries in the near future. Conclusions - Due to the nutritional distinctions comparing to the western style lettuces, domestic leaf lettuces could be one of the important vegetables in the school meal programs. To make it happen, we would better devise diverse recipes to make a salad with it, instead of only using as a wrap vegetable. Meanwhile, novel lettuce varieties need to be developed, which are favorable to the students and also easy to be handled with while processing. Overall, to achieve international competence in the lettuce industries, we need to create elite lettuce varieties that satisfies domestic farmers as well as customers, suitable to various niche markets, such as school meal program. Thus, efficient breeding programs using genomics approaches should be established in advance and careful monitoring on the preference of the related customers for a niche market be continued persistently.