• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.6
• /
• pp.48-56
• /
• 1989

Contact-type linear image sensors for facsimile have been fabricated by means of rf glow discharge decomposition method of silane. The dependence of their electrical and optical properties on rf power, $SiH_4$ flow rate, ambient gas pressure, $H_2SiH_4$ ratio and substrate temperature are described. The a-Si:H monolayer demonstriated photosensitivity of 0.85 and $I_{ph}/I_d$ ratio of 100 unger 100 lux illumination. However, this monolayer has relatively high dark current due to carrier injection from both electrodes, resulting in low $I_{ph}/I_{dd}$ ratio. To suppress the dark current we have fabricated $SiO_2/i-a-Si:H/p-a-Si:H:B$ multilayer film with blocking structure. The photocurrent of this multilayer sensor with 6 V bias became saturated ar about 20nA under 10 lux illumination, while the dark current was less than 0.2 nA. Moreover, the spectral sensitivity of the multilayer film was enhanced for short wavelength visible region, compared with that of the a-Si:H monolayer. These results show that the fabricated photocon-ductive film can be used as the linear image sensor of the facsimile.

• Journal of Family Resource Management and Policy Review
• /
• v.9 no.1
• /
• pp.131-146
• /
• 2005

The farming type in Korea is predominantly a small farm managed by family members. This study mainly examines the current usage of the website of family farms as a management tool for small farm business and discusses the strategies for effective utilization of the website. A county that currently employs governmental project of information system was purposely selected. Among all the websites operated by small farm businesses in that county, websites of which purpose is introduction of the business, advertisement, or e-business were included for analysis; it yielded total seven websites, The study was conducted with two phases; on-line website analysis and interview with business owners. The websites were analyzed based on four categories; content, interface, design, and site management. With regard to the content of the websites, the lack of connection between domain names and product names was found. Moreover, the problem relevant to site management was shown as low utilization of bulletin boards and delayed upload of new information. However, design and interface were comparatively well presented. Business owners reported that the motivation to initiate the websites was mostly supports from the governmental project for the agricultural information system. The barriers to effective management of websites were found i) business owner's misinterpretation of business website with e-business ii) very limited opportunity for website management education in small farm business, and iii) lack of regional infrastructure for information system. Based on the findings, this study suggests as followed; i) construction of infrastructure should be preceded to make effective management for websites; ii) education for website management should include small business management strategies as well as computer skills, iii) the education should be provided in diverse ways considering subject's characteristics iv) small farm business owners should be informed that their websites could play a role only to provide information about the products and hand over the practical load for e-business to retailing web sites such as portal shopping mall; and v) wives' participation should be encouraged.

• BMB Reports
• /
• v.42 no.6
• /
• pp.331-337
• /
• 2009

We investigate the correlation between the glycosylation modified prion proteins and apoptosis. The wild-type PRNP gene and four PRNP gene glycosylated mutants were transiently expressed in HeLa cells. The effect of apoptosis induced by PrP mutants was confirmed by MTT assay, Hochest staining, Annexin-V staining and PI staining. ROS test detected ROS generation within the cells. The mitochondrial membrane potential was analyzed by the flow cytometry. The expression levels of Bcl-xL, Bax, cleaved Caspase-9 proteins were analyzed by Western Blot. The results indicated that the expressed non-glycosylated PrP in HeLa cells obviously induced apoptosis, inhibited the growth of cells and reduced the mitochondrial membrane potential, and more ROS generation and low levels of the apoptosis-related proteins Bcl-xL, the activated the cleaved Caspase-9 proteins were found. The apoptosis induced by non-glycosylated PrP demonstrates that its underlying mechanism correlates with the mitochondria-mediated signal transduction pathway.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.2
• /
• pp.237-247
• /
• 1993

Carbon fiber reinforced plastics(CFRP) have gained increased application in aerospace structures because of their specific strength and stiffness, but are sensitive to impact-induced damage. An experimental investigation was carried out to evaluate the impact resistance of CFRP according to the ply angle. The specimens of angle ply laminate composites were employed with [0.deg. $_{6}$/ .deg.$_{10}$/0.deg.$_{6}$], in which 6 kinds of ply angle such as .deg.=15.deg., 30.deg., 45.deg., 60.deg., 75.deg. and 90.deg. were selected. The impact tests were conducted using the air gun type impact testing machine by steel balls of diameter of 5 mm and 10 mm, and impact-induced damages were evaluated under same impact speed of V=60m/s. The impact damaged zones were observed through a scanning acoustic microscope (SAM). The obtained results were summarized as follows: (1) Delaminations on the interfacial boundaries showed th directional characteristics to the fiber directions. The delamination area on the impact side (interface A) was considerably smaller compared to that of the opposite side (interface B). (2) Cracks corresponding to other delaminations than those mentioned in SAM photographs were also seen on the impact damaged zone. (3) The delamination patterns were affected by the ply-angle, the dimensions of the specimen, and the boundary conditions. (4) The impact damaged zone showed zone showed the delamination on the interfacial boundaries, transverse shear cracks of the surface layer, and bending cracks of the bottom layer.r.r.r.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.9
• /
• pp.1115-1125
• /
• 1997

Experiments have been conducted to obtain local and average heat transfer coefficients associated with impingement of a row of circular, free surface-water jets on a constant heat flux surface. Nozzle arrays are a row of 3 jets (nozzle dia.=4.6 mm) and a row of 5 jets (nozzle dia.=3.6 mm), and the nozzle configuration is Reverse cone type revealed good performance in heat transfer. Nozzle-to-plate spacings ranging from 16 mm to 80 mm were investigated for two jet center to center spacings 25 mm and 37.5 mm in the jet velocity of 3 m/s (R $e_{D}$=27000) to 8 m/s (R $e_{D}$=70000). For a row of 3 jets and a row of 5 jets, the stagnation heat transfer of the central jet is lower than that of adjacent jets. In the wall jet region between jets, for small nozzle-to-plate spacing and large jet velocity, the local maximum in the Nusselt number was observed, however, for small jet velocity or large nozzle-to-plate spacing, the local maximum was not observed. Except for the condition of $V_{O}$=8 m/s and H/D=10, the average Nusselt number reveals the following ranking: a row of 5 jets, a row of 3 jets, single jet. For a row of 3 jet, the maximum average Nusselt number occurs at H/D=8 ~ 10, and for a row of 5 jets, it occurs at H/D=2 ~ 4. Compared with the single jet, enhancement of average heat transfer for a row of 3 jets is approximately 1.52 ~ 2.28 times, and 1.69 ~ 3.75 times for a row of 5 jets.ets.s.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.5
• /
• pp.442-449
• /
• 1984

Turbulent jet flow has been studied in many ways; a plane jet, a rectangular jet, an annular jet, a round jet, a wall jet, a parallel jet, a valve jet, a cross jet, a slit jet and etc. In this report, a 45.deg. cross jet flow was tried by using two same dimensioned nozzels(dia..phi.20)which were set up at the exit of the subsonic wind tunnel. Each jet flows to the direction of 22.5.deg. to the axis of downstream of the mixed flow. The centerline of each jet meets at the distance of 217.3mm and their mixing flow could be imagined to develop beyond that distance, so the measurement was effectuated at X/X$_{0}$=1.2-1.5. The section of the mixed flow a elliptic circle which is formed by the 22.5.deg. inclined flows to the X direction. This experimental study aimed at the investigation of the turbulent mixing process of two jets; the mean velocities, the turbulent shear stresses, the correlation coefficients, and the momentum were respectively measured. The mean velocity distribution profiles of the down-stream component measured in the Y direction coincide well with the empirical equation of Gortler and those measured in the Z direction agree with the equation of H. Schlichting. Other mean velocities V over bar and W over bar components were randomly distributed. The higher values with same order of the intensity of turbulence were largely distributed at the central part of the flow. The momentum was decreased up to 70% by the shock losses and the development of intense turbulences, but it kept its value constantly beyond X/d=14. Two-channel hot-wire anemometer systems (model 1050 series), X-type hot-wire made of tungsten (dia. .phi.e.mu.m, long 3mm, model 0252 T5), a computer(model HP 9845B0, and a plotter (model HP 9872C) were used for the experiments and the analyses.s.

• The Journal of Korean Medicine
• /
• v.27 no.1 s.65
• /
• pp.220-228
• /
• 2006

Objectives : Interleukin-1 (IL-1)${\beta}$ in articular chondrocytes regulates differentiation, apoptosis, and inflammatory responses. It is still controversial, So, we investigated IL- $1{\beta}$ induces chondrocytes dedifferentiation and death. Also, we studied the role of the mitogen-activated protein kinase (MAPK) subtypes on IL-$1{\beta}$-induced dedifferentiation and apoptosis. Methods : To evaluation of dedifferentiation by chemokines of chondrocytes, we assessed such as proteoglycan, collagen, MMP-3 and MMP-13 by RT-PCR analysis. Also, to assess of apoptosis effect by chemokines, we measured annexin V/propidium iodode (PI) and sub G1 cells in chondrocytes by flowcytometric analysis Results : IL-$1{\beta}$ treatment did not affect activation of ERK-1/2, but stimulation of p38 kinase. Inhibition of phospho ERK-1/2 with PD98059 enhanced IL-1b-induced dedifferentiation, and apoptosis up to 13.5%, whereas inhibition of phospho p38 kinase with SB203580 inhibited dedifferentiation, and apoptosis. Conclusions : Our results indicate that SB203580, p38 kinase inhibitor, inhibits IL-$1{\beta}$-induced dedifferentiation, and apoptosis by the inhibition of type II collagen expression and proteoglycan synthesis of rabbit articular chondrocytes.

• Fashion & Textile Research Journal
• /
• v.13 no.6
• /
• pp.848-855
• /
• 2011

The purpose of this study is to develop design for daily hanbok with Jacquard textile design developed by using the traditional patterns that suit the needs and lifestyles of the middle and old aged group. This study will also develop Jacquard textile design that has elaborate and luxurious patterns and abundant expression of colors using the traditional patterns that suit the needs and lifestyles of the middle and old aged group. Developing daily hanbok design for woman's casual and formal occasion will contribute to fashion business significantly by popularization of daily hanbok as one of the important fashion genre. The "Texpro Design CAD V8.21" program was used for the textile design. A total of 2 designs were developed as the Jacquard textile design with traditional patterns using flower motifs. One type of fabric was produced for each of the textile design with a color selected from "Pantone Color Chips". And finally, four woman's daily hanbok design for either casual or and formal style were developed and these daily hanboks were consisted of one set of jacket and trouser, durumagi, one set of jacket and skirt and one set of vest and trouser. And the actual garments were constructed and the design procedure and the photos of these works were presented. This study showed the possibility of producing highly sensible daily hanbok that suits the fashion trend of middle aged women and the widening of consumer range and the creation of new market by developing Jacquard textile design.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.246-250
• /
• 2003

In this study, two new types of micro-grippers in which micro-fingers are actuated by piezoelectric multi-layer benders and stacks are introduced for the manipulation of micrometer-sized objects. First, we constructed a 3-chopstick-mechanism tungsten gripper, which is composed of three chopsticks: two are designed to grip micro-objects, and tile third is used to help grasp and release the objects through overcoming especially electrostatic force among some surface effects including electrostatic, van der Waals forces and surface tension. Second, a 2-chopstick-mechanism silicon micro-gripper that uses an integrated force sensor to control the gripping force was developed. The micro-gripper is composed of a piezoelectric multilayer bender for actuating the gripper fingers, silicon fingertips fabricated by use of silicon-based micromachining, and supplementary supports. The micro-gripper is referred to as a hybrid-type micro-gripper because it is composed of two main components; micro-fingertips fabricated using micromachining technology to integrate a very sensitive force sensor for measuring the gripping force, and piezoelectric gripper finger actuators that are capable of large gripping forces and moving strokes. The gripping force signal was found to have a sensitivity of 667 N/V. To the design of each of components of both of the grippers. a systematic design approach was applied, which made it possible to establish the functional requirements and design parameters of the micro-grippers. The micro-grippers were installed on a manual manipulator to assess its performance in tasks such as moving micro-objects from one position to a desired position. The experiment showed that the micro-grippers function effectively.

• ALGAE
• /
• v.33 no.2
• /
• pp.143-156
• /
• 2018

Dolichospermum is a filamentous and heterocytous cyanobacterium that is one of the commonly occurring phytoplanktons in the Han River of Korea. Morphological observations led to the identification of D. planctonicum-like filaments in seasonal water samples. In the present study, we successfully isolated these filaments using culture methods, and examined its morphology using light and scanning electron microscopy. The morphology of the D. planctonicumlike species differed from that of typical D. planctonicum; it had thin cylindrical-shaped akinetes, which were narrower towards the ends than at the center. This morphology is firstly described in the genus Dolichospermum. In addition, the akinetes in the filament developed solitarily and were distant from the heterocytes. Phylogenetic analysis of the 16S rRNA sequences showed that our Dolichospermum clustered with D. planctonicum and D. circinale, which have coiled trichome. However, phylogenetic analysis of the gene encoding rivulose-1,5-bisphosphate carboxylase (rbcLX) clearly separated our species from other Dolichospermum, forming a unique clade. Additionally, structures of D. planctonicum and D. hangangense strains were different type in Box-B and V3 region. These results demonstrated that the new Dolichospermum species was unique in morphology and molecular traits. Therefore, we propose this to be a new species belonging to genus Dolichospermum with the name Dolichospermum hangangense sp. nov.