• Bulletin of the Korean Space Science Society
• /
• 1993.10a
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• Journal of Korean Society of Forest Science
• /
• v.77 no.4
• /
• pp.429-444
• /
• 1988

Considering the recent trent toward the development of multiple-use of forest trees, investigations for comprehensive information on these young stands of Hinoki cypress are necessary for rational forest management. From this point of view, 83 sample trees were selected and cut down from 23-ear old stands of Hinoki cypress at Changsung-gun, Chonnam-do. Various stem growth factors of felled trees were measured and canonical correlaton analysis, principal component analysis and factor analysis were applied to investigate the stem growth characteristics, relationships among stem growth factors, and to get potential information and comprehensive information. The results are as follows ; Canonical correlation coefficient between stem volume and quality growth factor was 0.9877. Coefficient of canonical variates showed that DBH among diameter growth factors and height among height growth factors had important effects on stem volume. From the analysis of relationship between stem-volume and canonical variates, which were linearly combined DBH with height as one set, DBH had greater influence on volume growth than height. The 1st-2nd principal components here adopted to fit the effective value of 85% from the pincipal component analysis for 12 stem growth factors. The result showed that the 1st-2nd principal component had cumulative contribution rate of 88.10%. The 1st and the 2nd principal components were interpreted as "size factor" and "shape factor", respectively. From summed proportion of the efficient principal component fur each variate, information of variates except crown diameter, clear length and form height explained more than 87%. Two common factors were set by the eigen value obtained from SMC (squared multiple correlation) of diagonal elements of canonical matrix. There were 2 latent factors, $f_1$ and $f_2$. The former way interpreted as nature of diameter growth system. In inherent phenomenon of 12 growth factor, communalities except clear length and crown diameter had great explanatory poorer of 78.62-98.30%. Eighty three sample trees could he classified into 5 stem types as follows ; medium type within a radius of ${\pm}1$ standard deviation of factor scores, uniformity type in diameter and height growth in the 1st quadrant, slim type in the 2nd quadrant, dwarfish type in the 3rd quadrant, and fall-holed type in the 4 th quadrant.

• Investigative Magnetic Resonance Imaging
• /
• v.17 no.2
• /
• pp.133-143
• /
• 2013

Purpose : To evaluate and compare the accuracy of magnetic resonance imaging (MRI) and ultrasound (US) for detection and estimation of invasion depth of colorectal carcinoma (CRC) by correlation with histopathologic findings in vitro, and to find out the best MR pulse sequence for accurate delineation of tumor from surrounding normal tissue. Materials and Methods: Resected specimens of CRC from 45 patients were examined about tumor detectability and invasion depth of US using high frequency (5-17 MHz) linear transducer in a tube filled with normal saline and MRI in a 8-channel quadrate head coil. The institutional review board approved this study and informed consent was waived. MRI with seven pulse sequences of in- and out-of-phases gradient echo T1 weighted images, fast spin echo T2 weighted image and its fat suppression image, fast imaging employing steady-state acquisition (FIESTA) and its fat suppression image, and diffusion weighted image (DWI) were performed. In each case, both imaging findings of MRI and US were evaluated independently for detection and estimation of invasion depth of tumor by consensus of two radiologists and were compared about diagnostic accuracy according to the histopathologic findings as reference standard. Seven MR pulse sequences were evaluated on the point of accurate delineation of tumor from surrounding normal tissue in each specimen. Results: In specimens of CRC, both imaging modalities of MRI (91.1%) and US (86.7%) showed relatively high diagnostic accuracy to detect tumor and evaluate invasion depth of tumor. In early CRC, diagnostic accuracy of US was 87.5% and that of MRI was 75.0%. There was no statistically significant difference between two imaging modalities (p > 0.05). The best pulse sequence among seven MR sequences for accurate delineation of tumor from surrounding normal tissue in each specimen of CRC was fast spin echo T2 weighted image. Conclusion: MRI and US show relatively high diagnostic accuracy to detect tumor and evaluate invasion depth of resected specimen of CRC. The most excellent pulse sequence of MRI for accurate delineation of tumor from surrounding normal tissue in CRC is fast spin echo T2 weighted image.

• Korean Journal of School Psychology
• /
• v.16 no.3
• /
• pp.433-451
• /
• 2019

This study aimed to develop and validate the Classroom Problem Behavior Scale - Elementary School Version (CPBS-E) measure which is unique to classroom problem behavior exhibited by Korean elementary school students. The focus was on developing a universal screening instrument designed to identify and provide intervention to students who are at-risk for severe social-emotional and behavioral problems. Items were initially drawn from the literature, interviews with elementary school teachers, common office discipline referral measures used in U.S. elementary schools, penalty point systems used in Korean schools, 'Green Mileage', and the Inventory of Emotional and Behavioral Traits. The content validity of the initially developed items was assessed by six classroom and subject teachers, which resulted in the development of a preliminary scale consisting of 63 two-dimensional items (i.e., Within Classroom Problem Behavior and Outside of Classroom Problem Behavior), each of which consisted of 3 to 4 factors. The Within Classroom Problem Behavior dimension consisted of 4 subscales (not being prepared for class, class disruption, aggression, and withdrawn) and the Outside of Classroom Problem Behavior dimension consisted of 3 subscales (rule-violation, aggression, and withdrawn). The CPBS-E was pilot tested on a sample of 154 elementary school students, which resulted in reducing the scale to 23 items. Following the scale revision, the CPBS-E was validated on a sample population of 209 elementary school students. The validation results indicated that the two-dimensional CPBS-E scale of classroom problem behavior was a reliable and valid measure. The test-retest reliability was stable at above .80 in most of the subscales. The CPBS-E measure demonstrated high internal consistency of .76-.94. In examining the criterion validity, the scale's correlation with the Teacher Observation of Classroom Adaptation-Checklist (TOCA-C) was high and the aggression and withdrawn subscales of the CPBS-E demonstrated high correlations with externalization and internalization, respectively, of the Child Behavior Checklist - Teacher Report Form CBCL-TRF). In addition, the factor structure of the CPBS-E scale was examined using the structural equation model and found to be acceptable. The results are discussed in relation to implications, contributions to the field, and limitations.

• Korean Journal of Soil Science and Fertilizer
• /
• v.19 no.4
• /
• pp.283-289
• /
• 1986

To establish a suitability grouping system of paddy soils for multiple cropping of rice with other upland crops, the study was carried out after a few basic experiments. In succession to the results on basic experiment prior, the suitability system proposed and the results of application mentioned in this report were summarized as follows; 1. The factors of soil properties in the system were productivities represented by soil texture and drainage class, as well as salinity of surface and sub-soil pH of chemical properties were considered together with slope, warmth index, ground water table, parent materials etc. of soil physical or environmental conditions. The weights of the factors were combined with multiplicatively and additively so as the total marks of ideal soil to be 100. The system was composed with 5 suitability classes; over 91 mark is class I, under 60 mark class V, and each 10 point interval between classes. The limiting factors "P" (in the case that Physical properties or Productivity marks under 24), "S" (Surface slope less than 15) and "C" (Chemical condition below 15) etc. were appended up to two kinds to the classes except a part of soils in class I. 2. The areas where the warmth index exceed 110 in Yeongnam were 19% for class I, 22.7% for class II, 44.7% for class III, 11.5% for class IV, and 2.1% for class V. The rates in class I and II were slightly more than those of the whole country. 3. The points of each soil gained by the system had a positive correlation ($r=.922^{**}$) with the potential productivities.

• Journal of Korean Academy of Nursing
• /
• v.3 no.3
• /
• pp.36-49
• /
• 1973

This study was carried out for the objectives to collect the basic informations on the health behaviors of the elementary school children in an urban area in Korea. Seven hundred students were drawn to fill in the designed questionnaire which carries variety of Questions on health re-lated behaviors in general, eating habits, disease history, mental health, and sex education. Questionnaire were filled in by their parents. Major findings are as follows: ① 55.7% had habits of washing the hands before eating whereas 59.8% trashing their hands after toilet. The others had no idea of washing hands before eating and after toilet. ② 26,5% had habits of brushing the teeth twice a day 54.7% only once in the morning, and 2.6% once only in the evening. Thus, the idea of prevention from decayed teeth seems to be lacking among the school children. ③ Bathing habits were also inquired to get 40.3% of bathing more than once a week, 43.1% once every two weeks, and the rest of 16.6% once every one to three months. ④ 41.7% keep the regular bedding time whereas 58.3% irregular. Physical exercises were con-ducted by 76.6% on the ground while 23.5% did not practice any physical exercises at all. Of those physical exercises, rope skipping occupied 37.5%, and the other 66.9% consisted of 14 different kinds of individual type physical exercises such as gymnastic exercise. The main reasons for not enjoying exercises were different by sex; boys largely complained the inadequacy and lack of gymnastic facilities and girls felt in short of friends who could join the exercises. ⑤ 31.9% of the school children had been taking not much of food while 28.3% had unbalanced diets. Of these unbalanced diets, meat occupied 33.2% to be the priority to have an order of the following items such as vegetables, bread or noodle, and fishes as next to each. For eating habits, 88.5% take simple snack such as bread (38.4%, cookies, fruits, and candies in order. 25.8% of the children were provided such snacks or their parents regularly. Breakfast was sufficiently taken by 45.0% whereas 8.4% had never sufficiently. As to the lunch, 63.6% had sufficiently while 16.8% insufficiently. 70.6% take breakfast with all family members together and 30.4% separately. Correlation of sufficient taking of breakfast and eating together of tile family member's seems to be significant when we compare 72.5% of sufficient takers who enjoy breakfast together with the family members with 55.6% of insufficient takers who enjoy it with the family. This finding allows the investigator to point out the importance of table circumstances for children's eating. ⑥ The most common disease was catching a cold (38.8%), and the second was stomach trouble to be followed by the frequency of car sickness, headache, and skin infection. Doctors are consulted only by 23.9% when they are sick whereas 59.7% resorted to the drug stores. The lower the educational attainment of the parents, the lower the rate of visiting clinics. ⑦ 36.7% of their parents pointed out the problems of personality guidance as the most difficult thing at home 71.3% of their parents worried about and unsatisfied with their children's personality traits. Of these complains of the parents, impatience stood at the top to be tabulated at 24.1%, and 21.1% indicated narrow-mindedness. In line with this primary socialization at home, the most crucial problem seems to be related with the lack or recognition of the parents'own role when we find only 43.1% of the parents understood the importance of their own role for the home education of children; the latter group attributed tile responsibility of personality formation to the children themselves. ⑧ As to the sex educational aspects, 30.9% of children have ever asked about the physiology of reproduction or sexual matters to their parents, of those parents only 17.0% could give the constructive responses to the inquiries of the children. In companies on with these data, 25.6% recognized their own role in sex education for their own children while the large segments of the parents (51.1%) attributed the responsibility of sex education to tile low level of 38.3% who recognized the importance of sex education in the school curriculum and 25.1% of the parents insisted to wait until they get to know naturally about sex. 38.1% of the parents said they had some knowledge on sex from books while 16.9% through mass media. The next groups had common senses of sex from their own parents, school friends and other sources.

• Horticultural Science & Technology
• /
• v.33 no.2
• /
• pp.202-209
• /
• 2015

In this study, we investigated the cumulative effect of low temperature on bud dormancy release and bud break characteristics in 'Campbell Early' grapevine (Vitis labruscana B.) cuttings grown in water culture. Additionally, we observed the development of buds while exposed to low temperatures in an attempt to improve our understanding of dormancy and bud break. The shoots were collected 120 days after full bloom (DAFB; leaf abscission period), and the accumulated chill unit (CU) value was calculated by reducing the temperature to $7.2^{\circ}C$ at 125 DAFB. The rate of bud break was 100% in shoots collected at 150 DAFB, The period until the first bud break was two times longer than in the shoots collected 165 DAFB, and bud break speed was significantly reduced. These results indicate that buds are released from endodormancy after 165 DAFB, because at this point the bud break was complete (bud break rate 100%) and it occurred in a very short time period. During this period, when the low-temperature accumulated value was 321h and 442CU according to the CH and Utah models, respectively. Furthermore, the survival rate of main buds decreased rapidly after 165 DAFB, and survival rate of accessory buds was maintained at more than 90% without seasonal differences. The rate of flower bud formation of main buds was much higher than in accessory buds (1:0.23) before the release from endodormancy at 150 DAFB. The final ratio of accessory buds to main buds was high, 1:1.54, at 255 DAFB. Correlation analysis of each investigated factor revealed that bud survival rate and bud formation rate were related only for the main buds, and there was a close relationship between the survival rate of main bud and time. In addition, the survival rate of main buds was positively correlated to the rate of flower bud formation.

• Journal of Nutrition and Health
• /
• v.43 no.5
• /
• pp.433-442
• /
• 2010

The study aim was to examine the effect of sensory responses of subjects after 6-month dietary sodium reduction with the aid of nutritional education. Fourteen female college students voluntarily restricted their sodium intake for 6 months, during which time they received nutritional education on the low sodium diet. As a control group, 10 students, whose anthropometric measurement, sodium intake behavior, and blood pressure were not different from those of the experimental group, were maintained on a normal diet. For the sensory responses of subjects, the salt taste perception and pleasantness for graded (0.15-1.3%) NaCl solutions were measured by a 9-point hedonic scale. The optimum sodium concentration, urinary sodium excretion, and blood pressure were measured. All the measurements were done at the beginning and end of the experiment. The sensory evaluation revealed an absence of any difference between the two groups in salt taste perception and pleasantness responses at the beginning. After 6-month adaptation, the experimental group subjects showed higher responses to low NaCl solution (0.15, 0.3, 0.5%) in salt taste perception and pleasantness evaluation while the control group subjects exhibited the opposite response. The optimum sodium concentration was reduced from 105.6 mmol to 80.7 mmol (p = 0.015) and the urinary sodium excretion was also reduced from 1,398 mg to 906 mg (p = 0.041) only in the experimental group. Systolic blood pressure was significantly reduced in the experimental group, although there was no correlation between the urinary sodium excretion and blood pressure. The optimum sodium concentration was negatively correlated with the urinary sodium excretion (r = 0.418, p = 0.053), indicating that adaptation to low sodium diet can reduce sodium intake. Further study on the individual responses of subjects on a low sodium diet by periodical evaluation may provide useful data for setting the duration needed to stabilize a lowered appetite for sodium.

• Cartoon and Animation Studies
• /
• s.50
• /
• pp.275-297
• /
• 2018

Japan's mechanic animation is widely known throughout the world. 1952년, Japan's first mechanic animation and the first TV animation, , has been popular since it's creation in 1952. Atom, a big hit at the time, has influenced many people. Japanese mechanic animations convey their unique traits and world view to the public In this paper, we are going to discuss the change of the Japanese mechanical design through comparison of the mechanical design, which has been booming since the 1990s in Japan; and the . I expect the results of this analysis to depict Japanese culture and thought reflected in animation, which is a good indication of worldwide cultural view of animation. unexpectedly influenced the Japanese animation industry after it screened in 1995, and there are still people constantly reinterpreting and analyzing it. This is the reaction of the audience to anticipate the mystery and endless conclusions of the work itself. The design elements of Evangelion are distinguished from other mechanical objects. Mechanic design based on human biotechnology can overcome limitations of machine and make you feel more human. The pilot 's boarding structure, which can contain human nature, is reinforced in the form of an enterprising plug, and the attitude of excavation makes humanity more prominent than a straight robot. Thus, pursues a mechanic design that can reflect human identity. can be selected as the mechanic animation of the 80's, and the "Neon Genesis Evangelion" of the 90's shows it with a completely different design. By comparing the mechanical design of two works, therefore, we examine the correlation between the message and the design of the work. presents the close relationship between the identity of the mechanical design and the contents. I would like to point out that mechanical design can be a good example and theoretical basis for the future.

• Korean Journal of Occupational Health Nursing
• /
• v.11 no.1
• /
• pp.13-30
• /
• 2002

Industrial shift workers feels suffer mental stresses which are caused by unfamiliar day sleep, noisy environment, sleeping disorder by bright light, unusual contacts with family, difficulty in meeting with friends or having formal social meetings and other social limitations such as the use of transportation. Such stresses influence health of the workers negatively. Thus the health promotion policy for shift workers should be made considering the workers' ways of living and shift work specially. This study attempted to provide basic information for development of the health promotion program for industrial shift workers by examining predictive factors influencing health promotion behaviors of those workers. In designing the study, three power generation plants located in Pusan and south Kyungsang province were randomly selected and therefrom 280 workers at central control, boiler and turbine rooms and environmental chemistry parts whose processes require shift works were sampled as subjects of the study. Data were collected two times from September 17 to October 8, 1999 using questionnaires with helps of safety and health managers of the plants. The questionnaires were distributed through mails or direct visits. Means for the study included the measurement tool of health promotion behavior provided by Park(1995), the tool of self-efficacy measurement by Suh(1995), the tool of internal locus of control measurement by Oh(1987), the measurement tool of perceived health state by Park(1995) and the tool of social support measurement by Paek(1995). The collected data were analyzed using SPSS program. Controlling factors of the subjects were evaluated in terms of frequency and percentage ratio Perceived factors and health promotion behaviors of the subjects were done so in terms of mean and standard deviation, and average mark and standard deviation, respectively. Relations between controlling and perceived factors were analyzed using t-test and ANOVA and those between perceived factors and the performance of health promotion behaviors, using Pearson's Correlation Coefficient. The performance of health promotion behaviors was tested using t-test, ANOVA and post multi-comparison (Scheffe test). Predictive factors of health promotion behavior were examined through the Stepwise Multiple Regression Analysis. Results of the study are summarized as follows. 1. The performance of health promotion behaviors by the subjects was evaluated as having the value of mean, $161.27{\pm}26.73$ points(min.:60, max.:240) and average mark, $2.68{\pm}0.44$ points(min.:1, max.:4). When the performance was analyzed according to related aspects, it showed the highest level in harmonious relation with average mark, $3.15{\pm}.56$ points, followed by hygienic life($3.03{\pm}.55$), self-realization ($2.84{\pm}.55$), emotional support($2.73{\pm}.61$), regular meals($2.71{\pm}.76$), self-control($2.62{\pm}.63$), health diet($2.62{\pm}.56$), rest and sleep($2.60{\pm}.59$), exercise and activity($2.53{\pm}.57$), diet control($2.52{\pm}.56$) and special health management($2.06{\pm}.65$). 2. In relations between perceived factors of the subjects(self-efficacy, internal locus of control, perceived health state) and the performance of health promotion behaviors, the performance was found having significantly pure relations with self-efficacy (r=.524, P=.000), internal locus of control (r=.225, P=.000) and perceived health state(r=.244, P=.000). The higher each evaluated point of the three factors was, the higher the performance was in level. 3. When relations between the controlling factors(demography-based social, health-related, job-related and human relations characteristics) and the performance of health promotion behaviors were analyzed, the performance showed significant differences according to marital status (t=2.09, P= .03), religion(F=3.93, P= .00) and participation in religious activities (F=8.10, P= .00) out of demography-based characteristics, medical examination results (F=7.20, P= .00) and methods of the collection of health knowledge and information(F=3.41, P= .01) and methods of desired health education(F=3.41, P= .01) out of health-related characteristics, detrimental factors perception(F=4.49, P= .01) and job satisfaction(F=8.41, P= .00) out of job-related characteristics and social support(F=14.69, P= .00) out of human relations characteristics. 4. The factor which is a variable predicting best the performance of health promotion behaviors by the subjects was the self-efficacy accounting for 27.4% of the prediction, followed by participation in religious activities, social support, job satisfaction, received health state and internal locus of control in order all of which totally account for 41.0%. In conclusion, the predictive factor which most influence the performance of health promotion behaviors by shift workers was self-efficacy. To promote the sense, therefore, it is necessary to develop the nursing intervention program considering predictive factors as variables identified in this study. Further industrial nurses should play their roles actively to help shift workers increase their capability of self-management of health.