• 한국의류산업학회지
• /
• 제3권5호
• /
• pp.473-478
• /
• 2001

The newly developed cone drum twister is one of the outer surface contacting friction-twisting devices in false-twist texturing. An investigation of the drag angle for the newly developed cone drum twister texturing mechanism is reported. An analysis is given from which equations can be derived that relate to the conical angle of cone drum, wrapping angle, drag angle, and yam helix angle. Theoretical values of drag angle are calculated and discussed. It is shown that, as the helix angle and the projected wrapping angle increases, the drag angle also increases slowly until the helix angle of $40^{\circ}$ but after the helix angle of $40^{\circ}$ the drag angle increases rapidly. Furthermore the higher the projected wrapping angle and conical angle, the higher the drag angle of friction surface.

• Fibers and Polymers
• /
• 제4권4호
• /
• pp.161-168
• /
• 2003

An investigation of the dimensionless torque in the newly developed cone drum twister texturing mechanism is reported. The cone drum twister is one of the outer surface contacting friction-twisting devices in false-twist texturing. In this cone drum twister, a filament yam passes over the surface of the cone drum that rotates by the passing yarn without a special driving device. This research is composed of the theoretical analysis of the false twisting mechanism and the experimental analysis at room temperature. The equations have been derived which shows interrelationship of the conical angle of cone drum, the wrapping angle, the drag angle, and the yam helix angle. Theoretical values of dimensionless torque were calculated and were compared with the experimental results. It is shown that, as the conical angle and the projected wrapping angle increased, the dimensionless torque also increased. But the conical angle was reached to ${30.75}^{\circ}C$, the dimensionless torque decreased.

• 한국의류산업학회지
• /
• 제2권5호
• /
• pp.443-449
• /
• 2000

An investigation of the relative velocity of friction surface for the newly developed cone drum twister texturing mechanism is reported. The cone drum twister is one of the outer surface contacting friction-twisting devices in false-twist texturing. In this cone drum twister, a filament yam passes over the surface of the cone drum that rotates by passing the yarn without a special driving device. This research is theoretically composed of the analysis of the false twisting mechanism. The equations were derived by using the conical angle of the cone drum, projected wrapping angle, and yarn helix angle. Theoretical values of the relative velocity of friction surface were calculated and discussed. It is shown that, as the projected wrapping angle increased, the relative velocity of friction surface decreased. But as the conical angle increased the relative velocity of friction surface also increased.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.115-118
• /
• 1999

The twisting and bending extrusion process is developed by the $DEFORM^TM$-3D. Because the rectangular section of the extruded product has the symmetry line of cross-section area, the twisting and the bending of extruded product has not occurred. The product with the rectangular section is applied to the twisting and bending extrusion process through the twisted die surface and eccentricity die section. It is shown that the twisting of extruded product is caused by the twisted die surfaces and the bending of extruded product is causd by the eccentricity between the die section. The results by the analysis show that the twisting angle and the curvature of extruded products increases by the die twisting angle, the eccentricity, but decreases by the die length, and friction condition

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 춘계학술대회논문집
• /
• pp.254-257
• /
• 1998

The twisting and the bending of extruded product are caused by the shapes of products and by the shapes of die surfaces and by the shapes of die land. Because the elliptical shape and the circular shape of the extruded product have the symmetry line of cross-section area, the twisting and the bending of product has not occurred. But the analysis by the DEFORM-3DTM show that the twisting and the bending of extruded product can be occurred by the twisting of the twisting of the die land and by the curving of the die land. The results by the analysis show that the twisting angle of the extruded procduct increases by the twisting angle of the die land and the curvature of the extruded products increases by the radius of bending of the die land.

• 한국안전학회지
• /
• 제26권1호
• /
• pp.58-64
• /
• 2011

This study evaluated the effects of the handle width(shoulder width, 1.25${\times}$shoulder width, 1.5${\times}$shoulder width), height(3 levels : knee, medium, knuckle) and horizontal angle($0^{\circ}$, $10^{\circ}$) on the pushing, lifting, and twisting strengths which were required for carrying single or two wheel barrows. Twelve healthy college students(male) participated in the experiment. In each experimental condition($3{\times}3{\times}2$=18), the subjects exerted three forces(pushing, lifting, and twisting clockwise). The experimental conditions and three forces were tested in random order, and a minimum 2 minutes of rest was provided between exertions. Results showed that the mean and maximum pushing forces showed greater values when the horizontal angle was $0^{\circ}$ than $10^{\circ}$(p=0.016). However, the three independent variables had no statistically significant effects on the lifting forces(p>0.1). The mean and maximum twisting forces increased as the handle width became larger(p<0.05). Also, there was a marginal effect of the horizontal angle(p=0.065) on the twisting force. From the results of this study, the horizontal angle of $0^{\circ}$ and the wider handle width were suggested for the design of single-wheel barrows.

• 한국기계기술학회지
• /
• 제13권2호
• /
• pp.71-78
• /
• 2011

A kart is a vehicle without the suspension system and the differential gear. The kart frame as an elastic body plays the role of a spring. By the cornering of a kart, rolling, pitching and twisting motions are induced in the kart frame. Also the slip or noncontact of the wheel and a permanent deformation of the kart frame can be induced. In order to examine closely this phenomenon, measurement on height-displacements with various sensors and tracking system and analysis on the kart frame twisting characteristics with the rolling and pitching angle are needed. According to the measurement result, while driving in a curve at high speed the kart frame is quite twisted. Analysis on the measurement results shows that a kart used primarily in high speed requires a frame with low torsional stiffness and a frame material with high tensile strength and large elongation.

• 한국안전학회지
• /
• 제27권2호
• /
• pp.84-91
• /
• 2012

This study evaluated three forces (lifting, pushing and twisting) required to maneuver the single-wheel barrows according to handle height, width, horizontal angle and vertical angle. The four independent variables were varied in two levels. Handle height was varies in two levels : 'knuckle height (KH)' and 'KH + 0.1 ${\times}$ stature'. The two handle widths were '1.5 ${\times}$ shoulder width (SW)' and '1.75 ${\times}$ SW'. Two angles of $0^{\circ}$ and $15^{\circ}$ were used for horizontal and vertical angles. The 24 factorial design was used in the experiment. Twelve healthy male students (undergraduate and graduate) participated in the experiment. Subjects exerted three forces (pushing, lifting, and twisting clockwise) in each experimental condition. The order of 16 treatment conditions was determined randomly. Results showed that the effects of the four factors were different according to three forces. While lifting and twisting forces were higher in 'knuckle height', the pushing force was higher in 'KH + 0.1 ${\times}$ stature' (p < 0.05). Lifting and pushing forces showed higher values in the horizontal angle $0^{\circ}$ than in $15^{\circ}$. Handle width and vertical angle showed no statistically significant main effects on three forces (p > 0.05). Results of this study could be used as basic data for the ergonomic design of handle variables of one- or two-wheel barrows.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.373-375
• /
• 2008

In this paper the arc behavior in spiral type vacuum interrupter was analyzed by observing taken photographs from high-speed digital camera(10000frame/second) and current-voltage waveform from oscilloscope. As a result, the influence of twisting angle between contacts on arc behavior could be analyzed by matching and comparing arc voltage and photographs simultaneously.

• 소성∙가공
• /
• 제10권4호
• /
• pp.302-310
• /
• 2001

The twisting and extrusion process of the product with involute helical fin from the round billet is developed by the upper bound analysis. The twisting of extruded product is caused by the twisted inclined die surface connecting the die enterance section and the die exit section linearly. In the analysis, the internal shear surface is defined as the curved twisted plane from the twisting of die surface and the shear work is calculated by the consumption of shear energy. The increase rate of angular velocity is determined by the minimization of plastic work. The angular velocity of die exit can be controlled by the land length and the length of inclined die. The alular velocity assums to be increased linearly by the axial distance from the die enterance to the die exit. The results of the analysis show that the angular velocity of the extruded product increases with the die twisting angle, the reduction of area, and decreases with the die length, the friction constant.