• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.5
• /
• pp.116-122
• /
• 2014

In this study, 2 kinds of twist run models as exercise equipments are compared by durability analyses of fatigue and vibration. Maximum equivalent stresses are shown as 3.3 MPa and 16.6 MPa at the parts of stress concentrations at models 1 and 2. As the values becomes much lower than yield stress of this models, these models are shown to be safe designs. Model 1 becomes stronger than model 2 at natural frequency analysis. Fatigue lives become lowest at four axis parts and one axis part respectively in cases of models 1 and 2. Maximum damage probability at fatigue is shown to be 2.4% near the average stress of 0 in case of model 1 but this probability becomes 0.6 % in case of model 2. Model 1 has the maximum damage possibility 4 times more than model 2 at these states. As the result of this study is applied by the design of twist run, the prevention on fatigue damage and the durability are predicted.

• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.857-862
• /
• 2002

The bogie, when run on the twist track develops the wheel off-loading factor. This will be comfirmed by testing under different loading conditions and air springs inflated and deflated in all conditions. Under the most extreme twist track condition, EMU (Electrical Multiple Unit) shall not over the wheel off-loading requirement 60% defined on UIC / ORE report. This paper describes the wheel off-loading test procedure according to UIC / ORE and test result of DMRC EMU of INDIA carried out to find out to meet the requirement defined in UIC / ORE.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.4
• /
• pp.143-151
• /
• 2005

This study was conducted to investigate the technical factors of Cuervo forward straight vaults with single twist, single and half twists, and double twists actually performed by three execellent male gymnasts participated in artistic gymnastics competition of 2003 summer Universiade in Daegu and the 85th National Sports Festival in Cheongju. To accomplish the research goals the Cuervo vaults of three gymnasts were filmed by using three digital camcorders set by 60 Hz, and data were collected through the DLT method of three dimensional cinematography. The kinematic and kinetic variables as each phasic time, CM displacement velocity, release angle inclination angle hip joint angle landing angle, average horse reaction force average moment arm average torque, whoe body's total remote local angular momentum were analyzed, so the following conclusions were reached. Generally to perform the better Cuervo vault, a gymnast should touch down on the board with the great horizontal velocity of the whole body through the fast run-up, and touch down on the horse by decreasing the horizontal displacement of the whole body during the preflight, so raise CM height gradually within a short horse contact time. He should increase the horse reaction force through checking the horizontal velocity of the whole body effectively and the inclination angular displacement of the handstand, if so he can have the large vertical velocity of the whole body. By using the acquired the velocity and the angular momentum of the whole body, he can vault himself higher and twist sufficiently, then he can get better if the body could be tilted by swinging both arms and perform the cat twist with a little flexions at hip joints. According to the above outcomes we can judge that the best athletes is LuBin, the better is YTY, and the next is JSM.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.122-125
• /
• 1993

The various geometry of tap been developed in order to tap special workmaterial at considerably higher cutting speed than that of the conventional HSS tap. In this paper a piezo type tool dynamomerer is constructed and used to measure the torque. The experimental tests are run with various cutting speed. It is clarified that the process of chip formation strongly depends on rake angle, relief angel, angel of twist.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.299-307
• /
• 2005

The 180 km/h Korean Tilting Train(TTX) which is now developing as a part of the Korean National R&D project, was elaborately designed. As the tilting trains run curve track with the $30\%$ higher speed than normal trains, the higher centrifugal and dynamic force are expected. Furthermore the complex tilting system increase the probability of failure. Therefore it is very important for tilting train to ensure safety against derailment under the various kind of failed condition in the middle of running as well as normal operating condition. The TTX train have the relatively high roll stiffness to improve the lateral ride comfort and to limit the roll displacement on the curve. But the higher roll stiffness increase the risk of derailment on the twisted track. This paper describes the study to review the safety against derailment caused by the wheel unloading on the severely twisted track. The worst combination of maximum cant change with maximum twist defect was established by numerical simulation. And also it was assumed that the air bag deflated and still the train run its speed limit. Those kind of assumption might be the worst case from the view point of wheel unloading derailment on the twisted track. The dynamic simulation was done by means of VAMPIRE S/W and non-linear transient analysis. We found that derailment quotients Q/P was only slightly influenced by track twist but the wheel unloading was greatly influenced. And we ascertained that the higher roll stiffness the higher wheel unloading. In case of air bag deflated situation, the wheel unloading reached up to $100\%$ which means the wheel lift or jumped. Therefore it was concluded that the design need to be improved to ensure the safety against derailment on the maximum twisted track in case of air bag deflated and tilting train's speed limit.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.278-282
• /
• 2007

The riding comfort and the durability of train are effected by the rail irregularities such as track gauge, superelevation, alignment, longitudinal level, twist, cant and cross level. Inspection and estimation of irregularities are very important to maintain the rail condition. Generally, the EM120 has been utilized to measure the rail irregularities once a month in Korea. However, the EM120 can be operated at night time only, because the inspection speed of EM120 is much slower than the speed of high-speed trains. Also, the EM120 is too slow to inspect effectively for the whole commercial line. Therefore, we have mounted the track inspection system on the High-Speed Rolling Stock 350 eXperimental (HSR350X) and measured the rail irregularities to confirm the condition of a rail while running 300km/h. In this paper, the track inspection system mounted on HSR350X is mainly considered, and the measured results through test run are introduced.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.4
• /
• pp.98-107
• /
• 1996

In order to predict analytically torque, thrust force, tool life and chip formation in drilling, cutting models for chisel edge with various tool-chip contact length were developed in this type. Also, the experimental tests are run with various pilot holes. The following conclusions were obtained from the analysis. \circled1 It's also found experimentally that thrust force(Fz) decreases as pilot hole diameter increases. \circled2 Surface roughness for material(G) is larger that for material(J). The difference over two materials in roughness value about 0.5$mu extrm{m}$. \circled3 Flank wear of the drill in cutting material of G less than any other kinds of materials(F, G, H, I, J). \circled4 In drilling a deep hole on a workpiece over SM45C either twist drill. The chip was conical helix type at the fist suspensely change the two segment type and than two a long pitch helix style.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.8
• /
• pp.139-145
• /
• 1996

Tapping is one of the most widely used machining operations. There are several methodes of producing external screw threads, e.g. turning, milling with single or multiple cutter, rolling, and grinding, but the methods available for cutting enternal threads are less numerous, and for threads in small holes, tapping is employed almost exclusively. In this study, the tap with the various geometry has been developed in order to tap special workmaterial at considerably higher cutting speed than that of the conventional HSS tap. The experimental tests are run with various cutting speed by using a piezo type tool dynamometer to measure tapping torque. Tapping torque is affected by the design of the tap, which seems to be due to internal friction and shearing of the metal. It is clarified that the process of chip formation strongly depends on rake angle, relief angle, angle of twist.