• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.4
• /
• pp.138-146
• /
• 1997

The optimal drill helix angle, point angle, and cutting conditions are recommended in the study so as to maximize the drilling performance by investigating the experimental reaults concerning with the state of chip formation, roundness of machined holes, and geometry of projected burr at hole exit, which are examined under the conditions of various helix angles, drill point angles of twist drill, cutting speeds, and feeds in operional parameters. In the easiness of chip escape, the helical type of chip is producted when a helix angle is 30$^{\circ}$, drill point angle 118$^{\circ}$, 140$^{\circ}$and feed is st between 0.1 and 0.15mm/rev. Roundness of machined hole is improved when the helix angle is 37$^{\circ}$, drill point angle is 118$^{\circ}$, and feed is 0.15mm/rev. The height of projected burr at the button of machined hole increases when the drill point angle and helix angle becomes large.

• Textile Coloration and Finishing
• /
• v.15 no.6
• /
• pp.33-38
• /
• 2003

This study surveys the effects of POY physical properties and processing conditions of belt texturing machine to the textured yarns. The various textured yarns are made with the variations of 1st heater temperature, draw ratio, velocity ratio, and the physical properties of these specimens such as yam linear density, tenacity, breaking strain, and wet and dry thermal shrinkages are measured and analysed with the various processing conditions of texturing machine. Especially, the thermal characteristics of the textured yarns, which are affected at the fabric hands and the determination of the processing conditions in the dyeing and finishing processes, are investigated through the thermal stress analyser and DSC experiments.

• Structural Engineering and Mechanics
• /
• v.23 no.6
• /
• pp.713-737
• /
• 2006

This paper presents the results of an experimental investigation on the behaviour of 56 reinforced concrete beams subjected to pure torsion. The reported results include the behaviour curves, the failure modes and the values of the pre-cracking torsional stiffness, the cracking and ultimate torsional moments and the corresponding twists. The influence of the volume of stirrups, the height to width ratios and the arrangement of longitudinal bars on the torsional behaviour is discussed. In order to describe the entire torsional behaviour of the tested beams, the combination of two different analytical models is used. The prediction of the elastic till the first cracking part is achieved using a smeared crack analysis for plain concrete in torsion, whereas for the description of the post-cracking response the softened truss model is used. A simple modification to the softened truss model to include the effect of confinement is also attempted. Calculated torsional behaviour of the tested beams and 21 beams available in the literature are compared with the experimental ones and a very good agreement is observed.

• Fibers and Polymers
• /
• v.7 no.1
• /
• pp.70-72
• /
• 2006

This paper discusses the inter fiber cohesion in man made and blended yarns. The fiber parameters such as fiber length and fineness influence the cohesion. Studies have been focused on polyester and viscose spun yarns. Though polyester and viscose yarns show similar trend in cohesion, viscose yarns exhibit better cohesion clue to their serrated cross section. Studies on the effect of blend proportion of polyester cotton and polyester viscose yarns reveal that increase of polyester and viscose in the respective blends improve the inter fiber cohesion.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.5
• /
• pp.73-80
• /
• 2009

A tidal current turbine is designed and analyzed numerically by using blade element momentum theory. The rated power has a limitation because the diameter of the tidal current turbine cannot exceed the depth of sea water. This study investigates a horizontal axis tidal-current turbine with a rated power of 500 kW. NACA-6 series laminar foil shape is used for basic airfoil along the blade span. The distributions of chord length and twist angle along the blade span are obtained from the hydrodynamic optimization procedure. Prandtl's tip loss correction and angle of attack correction considering the three-dimensional effect are applied for this study. The power coefficient curve shows maximum peak at the rated tip speed ratio of 6.0, and the maximum torque coefficient is developed at the tip speed ratio of 4. The drag coefficient reaches about 0.85 at the design tip speed ratio.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2000.02a
• /
• pp.112-114
• /
• 2000

We fabricated BSCCO multifilaments superconductor tape and evaluated the effect of twisting on the microstructural evolution and critical current. Twist pitches of the tapes are in the range of 70 - 8 mm and uniformly deformed. It was observed that grain size and the degree of texture decreased as decreasing pith, probably due to the formation of the irregular interface between Ag and filaments. In addition, critical current of the tapes decreased to 6.5A with decreasing pitch to 8 mm, showing 48% of degradation compared to the untwisted tape(12.5 A). These reduction of critical current may be related to the interface irregularity, smaller grain size, worse texture and the presence of cracks due to the induced strain during twisting processing.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.5
• /
• pp.847-852
• /
• 2004

The wind turbine blade is the equipment converted wind into electric energy. The effect of the blade has influence of the output power and efficiency of wind turbine. The design of blade is considered of lift-to-drag ratio. structure. a condition of process of manufacture and stable maximum lift coefficient, etc. This study is used the simplified method for design of the aerodynamic blade and aerodynamic analysis used blade element method This Process is programed by delphi-language. The Program has any input values such as tip speed ratio blade length. hub length. a section of shape and max lift-to-drag ratio. The Program displays chord length and twist angle by input value and analyzes performance of the blade.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.363-368
• /
• 1995

A general method of solving inverse kinematics of three-joint manipulator composed of revolute joints or prismatic joints or combinations of those joints is presented in this study. In completing real-time control, it is very important to obtain the closed form solutions of inverse kinematics rather than iterative numerical solutions, because iterative numerical solutions are generally much slower than the corresponding closed form solutions. If it is possible to obtain the inverse kinematic solutions for general cases of considering twist anlges and offsets, the manipulator work space can be designed and enlarged more effciently for specific task. Moreover, in idustrial manipulators, the effect of main three joints is larger than that of the other three joints related to orientation in the view of work space. Therfore the solutions of manin three-joint are considered. Even The inverse kinematic equations are complicatedly coupled, the systematical solving process by using symbolic calculation is presented.

• Textile Coloration and Finishing
• /
• v.16 no.1
• /
• pp.1-4
• /
• 2004

This research surveys the twisting and untwisting tensions according to the various processing conditions of belt type texturing such as draw ratio, 1st heater temperature and velocity ratio. The 1st heater temperature was changed from 1606{\circ}C\; to\; 220^{\circ}C$, draw ratio was changed from 1.6 to 1.9 and velocity ratio was changed from 1.4 to 1.8. The twisting and untwisting tensions are measured with the variation of these processing conditions, in addition, the untwisting tension(T2) and tension ratio(T2/Tl) according to the various processing conditions are analysed with the false twist mechanism which is affected to the physical properties of draw textured yams.

• Journal of the Korean Home Economics Association
• /
• v.25 no.1
• /
• pp.11-18
• /
• 1987

The purpose of this study was to investigate the crease recovery and the elastic recovery as a function of the direction of plain woven fabrics. The crease recovery was measured by Mosanto's Method and the elastic recovery was investigated by Autograph for ten kinds of plain woven fabric samples. The results were as follows; 1. Values of crease recovery were in the order of bias>weft>warp. 2. The lengthening of recovery time had a little effect on crease recovery. 3. The directions of crease recovery were affected by that of thread twist. 4. The linearity was shown between total crease recovery and warp-weft crease recovery. 5. The linearity was found between crease recovery and elastic recovery in the fabrics.